金屬薄板 的英文怎麼說
中文拼音 [jīnzhǔbóbǎn]
金屬薄板
英文
metal sheet roof covering-
Sheet metal formability and methods - earing test
金屬薄板成形性能與試驗方法凸耳試驗Smoke pipes and bends made of metal sheet
金屬薄板制煙霧導管和彎管頭Lampholder ; push - in lampholder g13 for the mounting on sheet metal with a thickness of 0, 5 to 1, 0 mm
燈座.安裝在壁厚為?至mm金屬薄板上的g推入Lampholder ; push - through lampholder g13 for the mounting on sheet metal with a thickness of 0, 5 to 1, 0 mm
燈座.安裝在壁厚為?至mm金屬薄板上的g型穿N metallic materials - sheet and strip - determination of tensile strain hardening exponent n - values
金屬薄板和薄帶拉伸應變硬化指數Method of determining the tensile strain hardening exponent for metallic sheet and strip
測定金屬薄板材和帶材用拉伸應變硬化試樣的試驗方法Eaves gutters with bead stiffened fronts and rainwater pipes with seamed joints made of metal sheet
帶凸緣加固前端的檐溝和金屬薄板制接縫雨水管Eaves gutters with bead stiffened fronts and rainwater pipes with seamed joints made of metal sheet ; german version en 612 : 2005
金屬薄板制帶凸緣加固前端的檐溝和帶接縫的雨水管Standard test method for adherence of porcelain enamel coatings to sheet metal
金屬薄板搪瓷覆層的粘著性的標準試驗方法In this paper, a sheet metal assembly is as to the study object. msc / patran is used to modeling, calculating, and analyzing. the assembly variation is calculated using finite element method and pseudo random numbers which are produced by number theoretic method
本文以金屬薄板為研究對象,利用有限元軟體msc / patran對其進行建模、計算與分析,利用數論方法產生的偽隨機點與有限元法相結合計算薄壁件的裝配公差。Severe broke breaks may require an abration operation to hold the bone together with metal place plates and screws
嚴重的骨折有可能需要進行手術,用金屬薄板和螺絲把骨頭固定在一起。Standard specification for thermostat metal sheet and strip
恆溫雙金屬薄板和帶材標準規范The door was sheet metal welded on to the frame of iron
門是焊接在一個鐵框上的金屬薄板。Sheet metal anchorage with threads ; manufacturing processes
用螺紋的金屬薄板緊固法.加工方法Test method for ball punch deformation of metallic sheet material
金屬薄板材球擊變形試驗方法Standard test method for plastic strain ratio r for sheet metal
金屬薄板塑性應變率的標準試驗方法The four - probe method to measure the conductivity of metal thin board
金屬薄板電導率的四探針測量法0. 250 preferred thicknesses for uncoated thin flat metals under 0, 250 in
無鍍層金屬薄板的最佳厚度Sheet metal rim holes with screw thread ; prepunch hole diameters
帶螺紋的金屬薄板凸緣孔.預沖孔直徑Roofing products from metal sheet - specifications for fully supported roofing products of zinc sheet
金屬薄板屋面製品.全支承的鋅板屋面製品規范分享友人