鋪板結構 的英文怎麼說

中文拼音 [pūbǎnjiēgòu]
鋪板結構 英文
flat deck structure
  • 鋪 : 鋪名詞1. （鋪子; 商店） shop; store 2. （用板子搭的床） plank bed3. （舊時的驛站, 現多用於地名） post （often used in place names）
  • 板 : Ⅰ名詞1 （片狀硬物體） board; plank; plate 2 （專指店鋪的門板） shutter 3 [音樂] （打拍子的樂器） ...
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 構 : Ⅰ動詞1 （構造; 組合） construct; form; compose 2 （結成） fabricate; make up 3 （建造; 架屋） bui...
  • 結構 : 1 （各組成部分的搭配形式） structure; composition; construction; formation; constitution; fabric;...
  1. Metal toolbox is widely used to store all kinds of tools at the factorys and the repairing car or autocycle shop

    鐵制工具箱，有各種規格，結構合理，質量上乘，主要適合工廠、各種修理店鋪存放工具，也可與各種手工具組套使用，主要原料為冷軋板。
  2. Steel tool cart is widely used to store all kinds of tools at the factorys and the repairing car or autocycle shop

    鐵制工具箱，有各種規格，結構合理，質量上乘，主要適合工廠、各種修理店鋪存放工具，也可與各種手工具組套使用，主要原料為冷軋板。
  3. Steel decks, in other words, orthodox isomerism structures, are welded with various transverse and longitudinal reinforcing ribs. this results in the complexity of forces and deformatiort of the pavement layer above the deck

    鋼橋面板焊接在各種橫向、縱向加勁肋上，橋面板為正交異性板結構，決定了其上的鋪裝層受力變形的復雜性。
  4. Before studying the concrete composite deck pavement, we introduce the basic theory of touching analysis, and come up with the realization of touching analysis in the fem analysis considering the touch of concrete bridge cover plates, asphaltum concrete overlay with bridge cover etc. connect with the experiment on the spot of bridge, the software ansys is used to solidity modeling and analyzing an assembly simply supported bridge before adding overlap, after adding overlap etc., and study the influence of adding overlap on the underside bridge structures

    在進行裝配式混凝土簡支板橋復合鋪裝結構的探討性研究前，先介紹了接觸分析基本理論，並提出了考慮混凝土橋面板板間接觸、瀝青混凝土加鋪層與橋面接觸等接觸分析在有限元分析中的實現思路。結合一座裝配式簡支板橋現場試驗數據，採用ansys對該橋在加鋪前後進行了實體建模與計算分析，討論了瀝青混凝土加鋪層對下部結構物的影響。
  5. Abstract : this paper presents a new - type floating breakwater with the structure of “ duckweed ”. some circular wooden blocks were flexibly tied together and flat located on water surface. a series of experimental investigation were carried out. the experimental results show that 1 ) there are wave attenuation characteristics of the new - type floating breakwater ; 2 ) by comparing the two installation styles, the wave attenuation effectiveness anchored on the sea bed is better than that of anchored on the sea shore

    文摘:模仿水生植物「浮漂」的結構形式，設計一種新形式的防波堤.將多塊圓形木板柔性連接成一體，平鋪於水面，對其進行了一系列的消浪效果的初步試驗研究.試驗結果表明，該結構具有消浪性能，並且其固定方式採用系泊於水下的消浪效果優于系泊于岸邊的
  6. The test obsvervation include air temperature, ground temperature, foundation moisture, freeze depth, freeze capicity, freeze residual capicity, groundwater table and shape transform of canal lining, etc. throught systemic observation, analysis of impact about each factor on fundation freeze capicity, evaluate effect on anti freeze of various canal lining, comparison on technology and ecnomic of different method, a kind of main canal lining format is been recommended to engineering practice with siutable to ningxia local feature, fufilling the need of main canal safey i application, economic and practical, that is using polystyrene plate laying under concrete slate and grit taking replace of filling layer and optimizing design

    試驗觀測內容包括氣溫、地溫、基土含水量、凍深、凍脹量、凍脹剩餘量、地下水位和砌體外觀變化等項目。通過系統的觀測，分析各因素對基土凍脹量的影響，評價各種襯砌型式的防凍西安理工大學工程碩士專業學位論文脹效果，並進行技術和經濟綜合分析比較，推薦出了適合我區特點、滿足乾渠安全運行、經濟實用、防凍脹效果好的乾渠防滲襯砌型式，即混凝土板下鋪設聚苯乙烯板和砂礫石換填層結構型式，加以優化設計，用於工程實踐。
  7. It has streets paved with cobblestones and most of the houses are timber or brick - and - timber structures

    ：距成都47公里，鎮上街道全用石板鋪成，民居建築都屬于木材結構或磚木結構。
  8. The influence factors of fracture life are composites boards lay structure, wood - lacuna, and bamboo structure

    影響疲勞蠕變斷裂壽命分散性的因素主要有層合板的鋪設結構、木材缺陷和竹材結構等的影響。
  9. Given the thermal physical parameters of the envelops and the weather data, the above two parameters are determined by the following system design parameters : radiant panel dimension, radiant panel location and radiant panel layout style ( center or peripheral ). based on the thermal net model, digital analysis of the energy consumption and thermal environment are carried out to the several representative spaces under different design parameters, through which the relations of the heating load to the design parameters are obtained and can be a reference in the practical system design

    對于給定圍護結構熱物性參數和室外氣候參數的條件下，室內平均輻射溫度和室內空氣溫度的大小取決于系統的設計參數：輻射板的布置方式（周邊布置和中心布置） 、輻射板尺寸和輻射板鋪設位置。基於熱網模型，利用matlab軟體編程對採暖空間在不同設計參數下室內的熱環境和能耗進行數值分析，得出了低溫熱水地板輻射採暖系統的性能和能耗指標隨這些參數變化的規律，從而為低溫熱水地板輻射採暖系統的優化設計提供了參考。
  10. For laminate containing penetrated crack, " two planes " model is introduced to analyze the influence of repair parameters on the strength of repaired laminate, including such as patch size, patch thickness, patch layout, the location of rivets

    摘要針對含穿透性裂紋的損傷層壓板，採用「兩板」模型建立起機械連接修補結構有限元分析模型，分別計算補片大小、厚度、鋪排方式以及連接件位置等修補參數對修補效果的影響。
  11. At the same time, this paper point out it is a development direction making use of macromolecule material to develop flexible and inflexible mixed canal lining frame or flexible frame with credible technology, simple configuration and rational price

    同時，提出了增加混凝土板下鋪設聚苯乙烯板厚度並進行優化設計的方案，需進一步試驗研究;指出了利用高分子材料研製技術可靠、結構簡單、經濟合理的剛柔混合結構或純柔性結構作為渠道的襯砌結構，是今後渠道襯砌發展的方向。
  12. Abstract : fatigue cracks in ship hull structures are most likely to occur in the highly stressed structural details. the conventional fatigue analysis is largely dependent on the determination of stress concentration factors ( scfs ) at the locations considered. this paper is concerned with the stress concentration of cutout in transverse web for longitudinal stiffener. a series of finite element models is carried out for the stress analysis of predefined structural details. the tabulated scfs of typical cutouts ( abs tanker rules ) in transverse web for longitudinal stiffeners are presented based on the finite element analysis ( fea ) results

    文摘:疲勞裂紋往往發生在船舶結構的局部高應力區，而疲勞分析結果通常取決于任何準確確定結構的應力集中系數.本文研究為鋪設縱骨而在艙壁板上開孔的應力集中，採用有限元方法對預先給定的結構進行應力分析，基於有限元計算結果給出了艙壁板典型開孔（參見abs油船規范）的應力集中系數表
  13. We suggested one kind of planar metamaterials with periodic patterns tiled by two resonant components, which consist of triangular and pentagonal patch arrays and a metallic ground plate interconnected by via arrays together

    摘要設計了一種由兩種不同諧振單元套構而成並按周期排列組成的平面型異向性材料，該平面結構由三角形和五邊型的金屬貼片周期平鋪構成上表面，並通過金屬化導孔與下底板的金屬底板連接。
  14. Based on the simplified fundament and effective method, reference to the arrangement of the actuator placement and the control voltage can be offered to the composite adaptive structure

    該方法原理簡明、計算效率高，可為板殼型自適應結構的作動器鋪層位置設計和控制電壓分佈設計提供依據。
  15. In this research, fatigue life of laminate composite is predicted phenomenologically, dealing mainly with in - plane stresses without accounting for out - of - plane failures such as delamination. fatigue modulus is used as a physical parameter which helps to describe the basic fatigue behaviour of unidirectional laminates and obtain expressions for cumulative damages defined by strains. based on some typical fatigue test data for unidirectional composite laminates, a cumulative fatigue damage model is presented for predicting the fatigue life of multidirectional laminates with arbitrary stacking sequence under complicated fatigue loadings

    本文以碳纖維/樹脂基t300 / qy8911層壓結構為研究對象，從唯象的觀點出發，以疲勞模量為參量構造損傷函數，基於幾組最典型的單向板疲勞試驗數據，建立單向板在多軸循環應力作用下的疲勞壽命模型，並以此為基礎，發展同種材料體系的任意鋪層形式的多向層壓板在復雜循環載荷作用下的疲勞壽命預測方法。
  16. With the typical on - axis fatigue tests to get the relative s - n curves of unidirectional laminates, executed at certain stress ratio, it is possible to predict the fatigue life of multidirectional laminates subjected to cyclic stresses of different stress ratios. this would tremendously reduce test costs for laminate structures

    考慮了層壓板中單向層面內多軸應力和平均應力的影響，在已知單向板在確定應力比下受典型單軸循環應力的s - n曲線的基礎上，預測任意鋪疊次序層壓結構在不同應力比的循環載荷下的疲勞壽命。
  17. The results show that, for flexural - tensile fatigue test and shear fatigue test, the two kinds of structure of common asphalt concrete with strata stress absorbed layer and glass fiber grating had good ability to resist reflection cracking, while the effect of paving asphalt concrete directly on cement concrete slab was worse

    結果表明，對于彎拉型疲勞試驗和剪切型疲勞試驗，普通瀝青混凝土下面鋪設strata應力吸收層、玻璃纖維格柵2種結構都具有良好的抗反射裂縫的能力，而在水泥混凝土面板上直接加鋪瀝青混凝土類結構的效果最差。
  18. In addition, the strengthening principle for slab reinforced by random short steel fiber is illumined, which can be as a basic for sfrc ' s applying in engineering

    從理論上闡明混凝土板中摻入亂向短纖維的增強機理，分析分層鋪撒鑰纖維的施工方法的有效性和可行性，為其在結構工程中的應用提供理論依據； 3
  19. The selection of material, typical the structural designs, the mechanical property and the forming pressure of unmanned aircraft sandwich composite material have been studied in this paper. it has analysed and discussed the flexural properties of honeycomb sandwich plate delamination under bending loads in detail. and then the mechanical properties of the laminate panel are studied which are compared with honeycomb sandwich panel

    在圍繞某無人機蒙皮選用材料的基礎上，重點對蜂窩夾層結構的結構設計、力學性能、成型壓力對力學性能的影響，以及缺陷對蜂窩夾層結構復合材料的彎曲性能影響進行了較深入的實驗研究和理論分析，同時比較了蜂窩夾層結構中面板與同樣材料鋪層的疊層板力學性能的差異。
  20. In sso, the thickness of each stack of the laminate must be integer times as thick as that of single ply, the angle of each stack of the laminate is selected from a set of standard angles, and the stacking sequence can change arbitrarily. when material and ply angles of the laminate are selected, ga is used to giye the optimal laminate that meets the given requirements of thickness and geometry factors

    在550中，層合板各分層的厚度必須是單層材料厚度的整數倍，鋪層角取作一些標準的角度，各分層在層合板厚度方向上的相對位置可任意變化，利用ga求出滿足給定厚度和幾何因子要求的層合板最優鋪層結構。
分享友人
分享到 Line

分享到臉書