鋼絲滾道軸承 的英文怎麼說

中文拼音 [gāngsīgǔndàozhóuchéng]
鋼絲滾道軸承 英文
wire raceway bearing
  • 鋼 : 鋼名詞（鐵和碳的合金） steel
  • 滾 : Ⅰ動詞1 （翻轉; 滾動） roll; turn round; trundle 2 （走開; 離開） get away; beat it 3 （液體沸騰）...
  • 道 : Ⅰ名詞（道路） road; way; route; path 2 （水流通過的途徑） channel; course 3 （方向; 方法; 道理） ...
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 承 : Ⅰ動詞1 （托著; 接著） bear; hold; carry 2 （承擔） undertake; contract （to do a job） 3 （客套話...
  • 鋼絲 : steel wire; wire; wire-steel
  • 軸承 : [機械工程] bearing; axle bearing; bearing of shafts; gudgeon block; mechanical bearing; pillow; s...
  1. In the interest of adapting big size in radial direction, higher precision, higher angular rigidity, less moment of inertia, higher dynamic capability in the three - anxis simulation test turntable. researching the angular rigidity of the wire race ball bearings in axes direction, the adjustment mode and adjustment quantity to shafting, and analysing the contact stress of bearings in work is very necessity

    為了適應某些模擬轉臺研製中關于剛度高，轉動慣量盡量小，動態特性要求高等特殊要求，研究鋼絲滾道球軸承的軸向支撐剛度，軸系調整方式及調整量，以及該軸承在工作中的受力及應力狀況十分必要。
  2. Foundation in to the steel wire race ball bearing contact theoretical analysis computation, and the steel wire race ball bearing main friction form analysis, gave the bearing several kind of main friction to have the form in the work process, and gave the corresponding theoretical calculation formula

    在對鋼絲滾道球軸承點接觸理論分析計算的基礎上，進行了對鋼絲滾道球軸承的主要摩擦形式分析，給出了軸承在工作過程中幾種主要的摩擦產生形式，並給出相應的理論計算公式。
  3. This paper first conducts the research to the steel wire roller conveyer ball bearing rolling body and the steel wire roller conveyer spot contact question, gives the main geometry parameter of the zone of contact by the hertz contact theory, stress extreme value as well as contact body elasticity approach quantity formula, and acts according to the practical application to carry on the simplification, calculates the main parameter of the bearing zone

    本論文首先對鋼絲滾道球軸承滾動體與鋼絲滾道的點接觸問題進行研究，由hertz接觸理論給出接觸區的主要幾何參數，應力極值以及接觸體彈性趨近量的計算公式，並根據實際應用進行簡化，計算出課題所研究軸承接觸區的主要參數。
  4. The bearing spot contact and the friction carries on after the analysis, has carried on the simulation to the bearing work process, from simply established sigin ball two race model to the complex distinction the roller conveyer, the single ball four roller conveyers and the circular roller conveyer single ball four roller conveyer steel wire roller conveyer ball bearing finite element models, introduced the modelling method in detail, the restraint and the load infliction method

    在點接觸和摩擦分析的基礎上，對軸承的工作過程進行了模擬，按由簡單到復雜的研究步驟，分別建立起了單球雙滾道，單球四滾道和圓環形滾道單球四滾道的鋼絲滾道球軸承有限元模型，解決了建模模擬過程中實體模型的建立，約束和載荷的施加等一系列問題。
  5. Possessed more light mass, much less inertia, small size in axes direction, big size in radial direction, higher angular rigidity, frequently been of use in shafting of big radius

    鋼絲滾道球軸承具有重量輕，轉動慣量低，軸向尺寸小，徑向尺寸大，支撐剛度高等特點，常用於支撐大口徑中空軸系。
分享友人
分享到 Line

分享到臉書