鋼軌接頭焊接 的英文怎麼說

中文拼音 [gāngguǐjiētóuhànjiē]
鋼軌接頭焊接 英文
bond weld
  • 鋼 : 鋼名詞（鐵和碳的合金） steel
  • 軌 : Ⅰ名詞1. （路軌;軌道） rail; track 2. （比喻辦法、規矩、秩序等） rut; path; course Ⅱ動詞[書面語] （遵循; 依循） follow
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 鋼軌 : rail; metals; steel rail; railroad rail鋼軌間隙 dilatation joint; 鋼軌聯接板 joint bar; splice ba...
  • 接頭 : 1 （連接起來） connect; join; joint 2 （找人聯系） contact; get in touch with; meet 3 （了解情況...
  • 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
  1. With an introduction of the influences of the final quality of rail aluminothermic welding, such as : the quality of welding kits ( esp. the portion ), the result of pre - heating, the welding operation and the level of operators etc., this paper analyzes some problems when rail welding under special conditions

    摘要介紹了焊接材料質量、預熱效果、操作人員水平等因素對鋼軌鋁熱焊接接頭質量的影響，以及幾何誤差不同、軌頭寬度不等、寒冷氣候等特殊條件下進行鋁熱焊接應注意的問題。
  2. This paper analyzes the cause of small concaves around the welding seam in the long rail of guangzhou metro line 2, and presents preventive measures, such as increasing the under layer of the rail, limiting the weld seam, lowering the welding temperature etc

    摘要結合廣州地鐵2號線接觸焊焊接長鋼軌的實踐，分析了產生焊頭表面小凹痕的原因，提出改變墊高鋼軌的方式、縮小正火范圍、降低正火溫度、限制接頭錯牙量等預防措施。
  3. Based on the construction of guangzhou metro line 3 welding process and quality control, this paper introduces the mobile contact welding, analyzes some key points during the process of welding, such as welding of rails in curved sections, environmental protection, the measurement of straightness on the welding junctions located in curved sections, the maintenances of equipment etc., holds that more attention shall be given to these points

    摘要介紹了移動式接觸焊在廣州地鐵3號線中的施工工藝及施工過程；分析施工過程中應該注意的曲線鋼軌焊接、環境保護、曲線鋼軌焊接接頭平直度的測量、設備維修保養等技術要點。
  4. There are some technical requirements on grinding to at welding joints, the author proposes some solutions, aiming at improving the efficiency of at welding and the quality of the finished at welds

    對鋼軌鋁熱焊接接頭打磨預留量，以及打磨中出現「鞍形」磨耗、打磨發藍、燒傷的原因進行分析，並提出解決措施，以提高鋁熱焊接方法的效率及焊頭質量。
  5. Cast welded rail joint

    鑄焊鋼軌接頭
  6. The result shows that the new control system has convenient parameter modification, perfect controlling flexibility, rapid dynamic response speed, stable welding procedure ; the das of welding parameters has strong ability of anti - disturbance and the data is reliable. the control effect and practicability of the diagnosis system judging the welding quality are both good by using the characteristic values of welding process such as the percentage of the flashing time. gray - spots flaw in flash welding joints of rail is the least when the pole moves to and fro at the same velocity and the speed is slow

    結果表明：新型控制系統參數設置修改方便，控制柔性好，動態響應速度快，焊接過程穩定；焊接參數採集系統抗干擾能力強、數據可靠；以閃光時間百分比等焊接過程特徵量為判據診斷焊接質量效果好，實用性強；當動立柱的前進、後退速度相同且為低速時，鋼軌接頭中灰斑缺陷數量最少。
分享友人
分享到 Line

分享到臉書