錐形口 的英文怎麼說

中文拼音 [zhuīxíngkǒu]
錐形口 英文
bell
  • : Ⅰ名詞1. (錐子) awl2. (似錐物) awl-shaped things 3. (錐體) cone Ⅱ動詞(鉆) drill; bore
  • : Ⅰ名詞1 (人或動物進飲食的器官; 嘴) mouth 2 (容器通外面的地方) mouth; rim 3 (出入通過的地方) ...
  • 錐形 : [機械工程] taper; cone; cone-shape
  1. Railway transport equipment. tapered cotter pin

    鐵路運輸設備.
  2. Laboratory glassware. conical flasks. conical flasks with conical ground glass joint

    實驗室用玻璃器皿.燒瓶.帶有玻璃磨燒瓶
  3. Laboratory glassware. round bottom flasks. flat bottom flasks. flasks with conical ground glass joint

    實驗室用玻璃器皿.圓底燒瓶.平底燒瓶.燒瓶
  4. Tapered end mills for trapeziform runner with parallel shanks

    直柄梯型端銑刀
  5. The cheeks should be relatively flat and not bulge ( cheekiness ), maintaining the clean lines of the skull and should taper into the muzzle in a slight, graceful curve

    面頰相對平坦,不能凸出(厚臉皮) ,維持腦袋簡潔的輪廓線,向吻方向略略變窄,呈優美的
  6. Specification for open bottomed taper plug valves for 1st, 2nd and 3rd family gases up to 200 mbar

    壓力可達200毫巴家庭用一類二類和三類燃氣敞底部旋塞閥規范
  7. Rules for the inspection of electrodynamic cone loudspeakerof direct radiate type for export

    直接輻射式電動揚聲器檢驗規程
  8. The construction of the control ring seal for the coal gas wash pump was improved, the seal function and capacity efficiency of pump was increased adopting the stainless steel cone control ring, the industry stability and economy energy was obtained

    摘要對煤氣洗滌泵環密封結構和材料進行改進,採用圓不銹鋼環,提高了密封性能和泵容積效率,工業運行穩定,節省了電源。
  9. Clk - proliferation cyclone applicable to the collection of non - fiber drying of granular dust is the main characteristics of a conical dongshen, thus reducing the dust since the dongshen gas exports to the centre to short - circuit the possibility and install a conical reflector screen to prevent the two air separation will have to roll up the dust down, brought out by the increased flow, thereby enhancing the efficiency of dust

    Clk擴散式旋風除塵器,適用於捕集乾燥的非纖維性的顆粒狀粉塵,主要特點是筒身呈圓,因而減少了含塵氣體自筒身中心短路到出去的可能性,並裝有圓的反射屏,防止兩次氣流將已經分離下來的粉塵重新捲起,被上升氣流帶出,因而提高了除塵效率。
  10. The flask stand holds the flask to rotate or to make it incline in order to assist the end - effector taking positions and transplanting

    實驗結果顯示,此一機器人系統能適用於條狀與團狀苗在窄與廣培養瓶內扦?移植。
  11. General rules were validated and a new rule was discovered : i. e. the shape 0f these two stress fields are same, the equivalent stress of the round corner in the bottom reached its maximum at the first phase, the equivalent stress of the edge of hole reached its maximum at the third phase, the equivalent stress of flanging with cone - shaped punch descend more than that with column - shaped punch at the fourth phase i. e. the phase of deformation completed

    驗證了一般規律,也發現了新規律,即兩者的應力場狀相同,底部圓角處等效應力在變第1階段最大,孔邊緣處等效應力最大出現在變第3階段,第4階段(變終了時)沖頭翻邊的等效應力比柱沖頭翻邊時下降更大。
  12. A slender woodwind instrument with a conical bore and a double reed mouthpiece, having a range of three octaves and a penetrating, poignant sound

    帶有一個圓孔和雙簧管吹的細小的木管樂器,具有三個八度音域和穿透力強而尖利的聲音。
  13. Interchangeable conical glass ground joints

    可互換式玻璃磨接頭
  14. Due to its advantages of having no end - facet reflection, easy extension to a multi - port configuration, high tolerance for fabrication errors, and compact size, the tapered mmi is a good candidate for a coherent lightwave combiner to be used in large - scale photonic integrated circuits

    鑒于無後向反射,容易擴展為多配置,對實驗誤差有大的允許度和尺寸緊湊等優點,這種多模干涉的合波器是大型光子集成中所用的相干光波合波器的理想選擇。
  15. Keys and keyways and taper pins - specification for solid and split taper pins for general engineering purposes

    鍵和鍵槽及銷.第3部分:一般工程用整體的和開銷規范
  16. My mouth is full of sharp, cone - shaped teeth

    我的中滿是尖尖的牙齒。
  17. The paper analyses and compares the " factor effect on the flow in the pond by the numerical simulating software. the analysis shows the flow structures in the pond are not only related with the velocity of flow, angle of jet and the size of the entrance and so on, but also are related with the size of the pond

    根據計算,論文對閥消力池流態的影響因素進行了分析和對,比,分析認為,閥消力池內的水流流態與入射水流的流速、入流t角度和進尺寸以及水墊尺寸等反映淹沒撞擊射流的基本參數有關,也受消力池長度、寬度影響。
  18. Conical entrance orifice plate

    孔板
  19. Laboratory glassware ; interchangeable conical ground joints, dimensions, tolerances

    實驗室玻璃器皿.可互換的尺寸和公差
  20. Wrenches, box, angled, open end, combination, flare nut and tappet metric series ; errata

    螺母和螺桿組合成的開斜角開扳手.勘誤
分享友人