錐形心軸 的英文怎麼說
中文拼音 [zhuīxíngxīnzhóu]
錐形心軸
英文
conical mandrel-
In view of bearing capacity of the elastoplastic theory analysis, the author made a comparison between the achieved bearing capacity limit load pi / 4 of round base ( space problem ) and the limit load pi / 4 of bar groundwork foundation design ( plane problem ) from soil mechanics at home and abroad as well as foundation criterion, and explained why the value of formula in present design criterion from soil mechanics is inclined to be conservative. in the light of the author ' s many years experience of vibration test on the spot and the research work of relevant projects, the author worked over the dynamic pile testing of the bearing capacity of foundation and batholith, and gathered the parameter of dynamic analysis and testing. the author also talked over the difficult point of pile foundation design criteria in present batholith engineering world, i. e. the confirmation of batholith bearing capacity of pile end, from the following aspects : a ) confirmation of single axis counter - pressure strength of rock in house ; b ) f. e. m calculation of elastoplastic model ; c ) calculation of soil mechanics ; d ) deep well load test
然後，對巖土工程領域至今尚未解決，甚至不為人注意的考慮地基變形的地基承載力問題進行了實用化的探討，提出了考慮地基變形的地基承載力上程計算方法；對基於彈塑性理論分析的地基承載力國內尚未見報道的空間問題得到了圓形基礎（空間問題）的承載力界限荷載p _ （ 1 / 4 ） ，並與國內外土力學專著及地基基礎設計規范中的條形基礎（平面問題）的界限荷載p _ （ 1 / 4 ） ，進行了對比，從而定量上解釋了目前設計規范引用土力學承載力公式值偏於保守的這一情況；根據本文作者多年從事現場地基工程振動試驗及相關課題的研究工作，本文以截頭錐模型模擬地基，對地基（巖基）承載力的動測法進行了研究，為各類地基（包括巖基） ，匯總了動力分析和檢測川的參數：針對日前巖土工程界應用樁基設計規范中的難點? ?樁端巖基承載力的確定問題，從巖石室內單軸抗壓強度確定、基於彈塑性模型的有限單元法計算、土力學計算及深斤載荷試驗四方面進行了深入討論；本文作者根據多年現場載荷試驗的工程實踐，對深井荷試驗裝置的核心部分? ?反力裝置，設計了側壁支撐反力加載系統，該加載系統具有實用、簡便、穩定及安個等優點。Abstract : approximate methods for calculating aerodynamic heating rates on space shuttles are discussed. various methods are given for predicting the heating rate at axisymmetric stagnation points, general three dimensional stagnationpoints and the leading edge stagnation point of wings. numerous laminar and turbulent heating techniques for flat plates and cones are analyzed and compared. a brief review of some methods is presented to predict heating rate for winward centerline and lateral direction off the symmetry plane. the results show that the methods are simpler and can guarantee enought precision for predicting aerodynamic heating environment of space shuttles
文摘:介紹了國內外預測航天飛機氣動加熱的工程計算方法.給出了軸對稱、非軸對稱和機翼前緣等各種外形駐點熱流密度的計算，分析和比較了平板、錐體的層流和湍流熱流密度計算的各種方法，概述了航天飛機迎風面中心線和離開中心線橫向熱流密度的計算.計算結果表明，本文方法用在航天飛機氣動熱環境初步設計中比較簡單並且有足夠精度Cylindrical and 1 10 conical shaft ends. internal threads. center holes
園柱軸和1 10錐度的錐形軸端.內螺紋.中心孔Drill chuck mounting arrangements - taper arbors
鉆頭夾盤.錐形心軸Tool shanks with 7 24 taper for automatic tool changers - specification for functional dimensions of front faces of spindle holders for machine centres
帶7 24錐形自動刀具變換器的刀具柄.加工中心主軸托架的正面功能尺寸的規范Rolling bearings ; self aligning ball bearing ; double row with cylindrical and tapered bore
滾動軸承.向心滾珠軸承.帶圓柱形和錐形孔的雙列軸承With two structures of bore cylindrical or tapered and retainers made of steel sheet or synthetic resins, the bearings are characteristic of their spherically formed outer ring raceways allowing for misalignment within 3 degree deflection between inner ring and outer ring, so as to compensate concentricity and deflection errors
詳細信息:調心球軸承由圓柱孔和圓錐孔兩種結構，保持架的材質有鋼板、合成樹脂等，其特點是外圈滾道成球面形，具有自動調心性，可以補償不同心度和軸撓度造成的誤差，但其內、外圈相對傾斜度不得超過3度。分享友人