鍵盤傳送 的英文怎麼說

中文拼音 [jiànpánzhuànsòng]
鍵盤傳送 英文
keyboard send
  • 鍵 : 名詞1 [機械工程] （使軸與齒輪、皮帶輪等連接並固定在一起的零件） key 2 [書面語] （插門的金屬棍子）...
  • 盤 : Ⅰ名詞1 （盤子） tray; plate; dish 2 （形狀或功用像盤的東西） sth shaped like or used as a tray pl...
  • 傳 : 傳名詞1 （解釋經文的著作） commentaries on classics 2 （傳記） biography 3 （敘述歷史故事的作品）...
  • 送 : 動詞1 （運送; 傳送） deliver; carry 2 （贈送） give as a present; give 3 （伴送; 送別） see sb of...
  • 鍵盤 : fingerboard; keyboard; clavier; key panel; manual; keyshelf鍵盤編碼器 key encoder; key coder; 鍵...
  1. In the hardware design, the paper completes modules ’ design like outside memory, patulous a / d, patulous d / a, rs232 communication, ecan communication, led control, keyboard control, distant control, emulation, reset, logic voltage switch, dsp supply power regulate and ac - dc power circuit, as well as room layout design like anterior panel, back panel etc. and dsp transfers data with peripheral equipments except outside memory using serial ports. besides, the whole circuit is configured in interrupt response. thus, it can meet system demand as well as take full advantage of tms320f2812 ’ s hardware resource. in the software design, the paper finishs programs like the interface programms intercommunicates with people, the distant control program, ad and da modules ’ control program, in addition, the paper select the velocity and acceleration state - feedback algorithm and is written in the program. the software design uses dsp integrate exploiting environment named ccs2. 2 of ti inc. as software instrument, and programs with the combination of c language and assembly language. moreover, in order to maintenance or modify the software expediently and shorten software ’ s exploitation time, the design adopt software modularization technique. finally, some air cylinder experiments are carried out to proved that the pneumatic controller is very practical

    在硬體設計中，本文完成了片外存儲器擴展、 a / d擴展、 d / a擴展、 rs232通信介面、 ecan通信總線介面、液晶顯示控制、鍵盤控制、遠程控制、模擬、復位、邏輯電平轉換、 dsp工作電源校正電路和ac - dc電源等模塊設計以及控制器前面板、後面板等的空間布局設計。其中dsp與除外部存儲器的外圍設備之間的數據傳送全部採用串口通信，同時系統電路配置成中斷響應方式，這樣既滿足了系統要求，又充分利用了tms320f2812的硬體資源。在軟體設計中，本文完成了人機界面功能模塊、遠程控制模塊、 ad擴展模塊、 da擴展模塊、速度和加速度狀態反饋的控制演算法的程序設計。
  2. The keyboard sends a message to the bank's computer.

    鍵盤把信息傳送到銀行的計算機里。
  3. Provides keyboard routing for the child controls, thus ensuring that child controls can receive focus

    為子控制項提供鍵盤傳送，這確保子控制項可以接收焦點。
  4. It realizes the functions of storing and transferring the information of fire alarm, displaying time, scanning keyboards, the safe maintenance of system and so on. the part of wireless communication is controlled by at89c2051 mcu, mainly realizing transmitting and receiving data between controller and other detectors. the external signals received by a wireless module are transmitted to mcu through shaping circuit, and the signals of mcu are transmitted by a wireless module through tone modulation circuit

    人機交互部分以單片機c8051f020為核心，為用戶提供一個良好的操作環境，實現了火災報警信息的存儲及調用、時間的顯示、鍵盤的掃描、系統的安全維護等功能;無線通信部分由單片機at89c2051來控制，主要實現控制器與其它探測裝置之間信號的無線發射和接收，無線通訊模塊接收到的外部信號經過整形電路送入單片機，單片機發出的信號經過音頻調制再由無線通訊模塊發送出去，這樣實現了數據的無線傳輸;本文還從節能的角度出發，兼顧性能的可靠性，提出了一種合理的無線火災報警的信息傳輸模式。
  5. All the keyboard events will be propagated to the xim, which determines the appropriate action for the events based on the current state of the xic, and passes back the resulting characters

    所有鍵盤時間都被傳遞到xim ，它根據xic的當前狀態決定事件對應的正確動作，然後傳送回相應的字元。
  6. This system is developed based on high performance, low cost and many controllers inside of the embedded processor, and enlarged gpio for the plat of the hardware and software. this system is applied to the high - speed numerical control carving machine. show the operate interface by lcd, input the control code from the keyboard, the data is readed from the usb interface and store that in sdram

    本系統應用於高速數控雕刻機，以lcd為人機可視化操作界面，以編碼鍵盤為操作控制部分，以嵌入式處理器s3c44b0x晶元為核心，文件數據經usb口讀取u盤中的雕刻數據文件暫存於sdram中，經嵌入式處理器進行相關演算法處理，得出相應參數傳送到fpga ，由fpga控制輸出脈沖和脈沖間延時，通過高速光耦隔離（ 2mbit / s ）后輸出，控制步進電機的運轉。
  7. The module of user agent need accomplish these tasks of making the message, analyzing the information, user agent, negotiating about the media. the module of real - time transport need complete these tasks of converting the data, coding and decoding the data and receiving and sending the packet. the module of management of the system ' s source need manage the keyboard and display and so on

    用戶代理模塊需要完成消息的接收和發送、消息的生成、消息的分析、用戶代理的事務狀態機管理、呼叫雙方媒體流協商的功能；實時傳輸模塊需要完成數據轉換、數據的編解碼、數據包的生成和分解及數據包的發送和接收；系統資源管理模塊需要管理系統的鍵盤、用戶界面等。
分享友人
分享到 Line

分享到臉書