鑄件分析 的英文怎麼說

中文拼音 [zhùjiànfēnxī]
鑄件分析 英文
cast analysis
  • 鑄 : Ⅰ動詞（鑄造） cast; coin; make Ⅱ名詞1. （古國名） zhu, a state in the zhou dynasty2. （姓氏） a surname
  • 件 : Ⅰ量詞（用於個體事物） piece; article; item Ⅱ名詞1. （指可以一一計算的事物） 2. （文件） letter; correspondence; paper; document
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 析 : Ⅰ動詞1. （分開; 散開） divide; separate 2. （分析） analyse; dissect; resolve Ⅱ名詞（姓氏） a surname
  1. The operation principle and device to produce acetin and hydroxyethyl acetate for foundry firming agent were analyzed in the paper, and the choice of esterification catalyst and dehydrated agent in the esterifying process also were analyzed theoretically, and finally, the better producing operation device, catalyst and dehydrated agent were obtained

    摘要分析了鑄造用有機酯固化劑酯酸甘油酯和乙二醇醋酸酯合成工藝原理及裝置，同時對有機酯合成工藝條件中脫水劑和催化劑的選擇的理論依據進行了分析，得出鑄造用有機酯固化劑的最佳合成工藝裝置和脫水劑、催化劑。
  2. A detailed introduction was made to the properties of the wet coated sand suitable for multi - station shell mould shooting machine ; the development of a sort of high strength coated sand with low resin content : the shaping index and wetness adjusting process : analysis and prevention of peel back defect of shells made with overturning hopper process ; test method of peel back resistance of coated sand : pinhole defect analysis of high ni ductile iron shell mould castings and application of anti - pinhole coated sand

    詳細介紹適用於吹砂式多工位殼型機的濕態覆膜砂性能；高強度低樹脂量覆膜砂的研製；濕態殼型覆膜砂的成形性指數與調濕工藝；翻鬥法制殼時的脫殼問題分析和解決辦法；覆膜砂脫殼性檢測方法；高鎳球鐵件殼型鑄造表面針孔原因分析與抗針孔覆膜砂的應用。
  3. Third, on the base of expatiating on experimental research method and theoretical research method of joints, the paper points out two kinds of valid methods, which are used to analyze the tube joints stress of dendriform structure by making use of semi - analytical method and inelastic large deflection finite element analysis method, confirms to apply the evaporative pattern casting process as the facture method of dendriform structure cast joints, and detailed dissertates the casting theory, casting process, generation cause and prevention measure of casting flaws, heat treatment method and inspection standard about cast steel joints

    然後在闡述樹狀結構節點實驗研究方法和理論研究方法的基礎上，提出了利用半解析法和彈塑性大撓度有限元法兩種有效分析樹狀結構管節點應力的方法，並給出兩種方法的詳細表達式及它們各自的優缺點。通過對鑄鋼件常見製作方法的介紹，確定了採用消失模法作為樹狀結構鑄鋼節點的製作方法，並詳細論述了用消失模法製作鑄鋼節點的鑄造原理、鑄造工藝、鑄造缺陷產生的原因及防治措施、鑄鋼節點的熱處理方法以及檢驗標準。
  4. Based on the analysis of eutectoid transformation of sg ( spheroidal graphite ) iron, the numerical model of formation of ferrite and pearlite during the eutectoid transformation was improved

    摘要通過對球墨鑄鐵件共析轉變的分析，改進了球鐵件中鐵素體與珠光體形成的數學模型。
  5. In this paper, the reason and process of hot tear forming for the investment steel castings are analysed, the technological method of preventing hot tear is discussed, and the designing method of the self - cut - gate for shifting hot tear is introduced

    分析了熔模鑄鋼件熱裂產生的原因和過程，論述了防止熱裂的工藝措施，並介紹了自割內澆口轉移熱裂及其設計方法。
  6. The quality assurance system of foundry manufacturing process has been analyzed from the viewpoint of total quality control ( tqc ) in the paper

    本課題從全面質量管理（ tqc ）的角度分析了鑄件生產過程質量保證體系。
  7. Abstract : based on problems occurred during the service of the ls spiral conveyer, such as, jam of uncharging orifice, short usefull life of the drop - hanger bearings, easy rupture of connecting parts ; quick wear of spiral vane, etc. and according to the practice of casting process, analysis of break downs, the author put forward the improvement ideas in order to promote the level of the design and manufacture for spiral conveyers

    文摘:針對ls型輸送機使用中存在的一些問題，如卸料口積料堵塞、吊軸承使用壽命短、連接件易斷裂、螺旋葉片磨損快等問題，依據在鑄造生產中的使用實踐，進行故障分析，提出了改進思路，以利提高螺旋輸送機整體設計和製造水平。
  8. The research showed that basin is the more important feeding resource than runner in runner type gating system in lost wax casting. therefore, on the basis of the basin as feeding resource, runner and ingate as feeding channel, a new design method for runner type pouring and feeding system in investment casting was developed. the corresponding feeding mathematical pattern and allowable total weight listed for casting cluster with different basin were established after analyzing the practical feeding of basin and the calculating process for design was described in detail

    在熔模鑄造橫澆道型澆注系統中，澆口杯是比橫澆道更為重要的補縮源，因此在立足於澆口杯為補縮源、橫澆道和內澆道為澆注補縮通道的基礎上，開發了適用於熔模鑄造橫澆道型澆注補縮系統設計的新設計方法，在詳細分析了澆口杯的實際補縮情況后，建立了相應的數學補縮模式和不同澆口杯的鑄件組許用鑄件總質量表，並具體介紹了設計計算過程。
  9. With theoretical analysis and production practice, the omens of cupola melt oxidation, the mechanism and reasons of iron melt oxidation, its influence on castings quality were described, and measures to prevent melt oxidation were proposed

    摘要通過理論分析和生產實踐，敘述沖天爐鐵液氧化的特徵、鐵液氧化的發生機理和原因、鐵液氧化對鑄件質量的影響，以及在生產中預防鐵液氧化的措施。
  10. Based on the mechanism of hot cracking formation of castings, the cracking defects of furnace door frame castings was analyzed, and found that the main reasons causing cracking are as follows : construction of the casting was not reasonable, gating system was not proper, and pouring temperature was too high

    摘要根據鑄件產生熱裂紋的機理，對爐門框裂紋缺陷進行分析，找到了裂紋產生的主要原因是鑄件結構和澆注系統不合理，以及澆注溫度過高。
  11. The composite material, which is used to make muller plow of sand mill, is prepared by the method of cast - infiltration and the technology parameters for making composite material is optimized. then the effects of the matrix component on composite layer also are disccused

    通過試驗對利用鑄滲法在鑄件表面獲得一定厚度復合材料層的形成機理進行了理論分析，優選了利用鑄滲法在鑄件表面制備復合材料的工藝參數（澆注溫度、合金膏塊的厚度、澆注位置等） 。
  12. On the basic of the detailed analysis on main causes and main prediction methods of casting shrinkage / porosity, we put forward two methods to describe the solid phase rate of materials solidification. one is liner - distributing method, and the other is parabola - distributing method. and then, we apply the former to the system

    本文在充分分析鑄件縮孔縮松產生機理與主要預測方法的基礎上，提出了材料凝固固相率的線性分佈法和拋物線分佈法，並將前者應用於系統中；同時提出了溫度梯度法和新山判據法的實現演算法，此演算法具有一定的靈活性。
  13. Analysis results of histogram statistics and section electron microscopic scan technique, are that fracture feature of the cracks of the hbbb is similar and the crack is multi - source strain fatigue one. internal defects of the cast, such as impurities, gas holes, etc, are the main causes for early cracks. the contrast analysis of static strength, model and transient respond on three structures with fem proves that geometrical stress concentration in partial area has influence on early crack, also

    利用直方圖等統計方法和電鏡掃描技術對該抱軸箱體裂紋分析的結果是：抱軸箱體的裂紋斷口特徵相近，裂紋性質屬于多源性低周疲勞裂紋，鑄件中的夾雜、氣孔等內部缺陷是導致過早裂損的主要原因；利用有限元法對該抱軸箱體三種結構的靜強度、模態和動態響應對比分析，證實了局部幾何性應力集中對過早裂損也有一定影響。
  14. Abstract : some kinds of defects in plate castings of gray cast iron are discussed, and varies kinds of gating systems and their advantages or disadvantages are analysed in this articles

    文摘:本文介紹了平板類灰鑄鐵件易產生的各類鑄造缺陷及其在生產中常用的各種澆注系統，並分析了各類澆注系統的優缺點。
  15. The defect of crack in the engine block of 8170 diesel engine has beem researched and analyzed, which can be solved and avoided through the following measures : optimizing the structure of engine block casting, improving alloying technology, perfecting pouring process and adopting normal inoculation before furnace and metal - stream inoculation during the period of pouring

    摘要對8170缸體裂紋缺陷進行了探討分析，通過優化鑄件結構，改進合金化工藝，完善澆注工藝以及隨流孕育與爐前孕育工藝相結合等措施，使裂紋缺陷解決。
  16. A new electroforming technique, numerical control jet electroforming, was proposed, it not only can solve some problem of tradition electroforming but also can make nano metal block and metal accessory, and the elemental research on the new technique was carried out

    本文提出了一種新的電鑄工藝方案? ?數控噴射電鑄，不但能解決傳統電鑄的一些缺陷，而且可以制備納米金屬塊體和金屬零件，並通過理論分析和試驗對該工藝進行了基礎性研究。
  17. The company has the advanced precision casting, the machine - finishing equipment and the check - out facility, including : disk wax mould machine, moistening slurry machine, intermediate frequency melting furnaces, cnc tooling machine, spectrometer, metallurgical microscope, hardness testing machine, computer material test machine. and so on

    公司擁有先進的精密鑄造、機械加工設備及檢測設備，其中包括：雙工位射蠟機、圓盤射蠟機、沾漿機、中頻熔化電爐，光譜分析儀、金相顯微鏡、硬度試驗機、電腦萬能材料試驗機， cnc數控車床、普通鉆銑床及閥門管件殼體、密封試驗機等。
  18. The subsystem of the casting foresee and analysis established the mathematical model of the quantitative linear regression analysis for the compacted graphite cast iron defects. it provided guarantee for predication and control of casting defective index within permissive ranges

    鑄件質量分析及預測子系統建立了蠕墨鑄鐵件缺陷定量分析的線性回歸分析數學模型，為預測及控制缺陷廢品率在規定范圍內提供保證。
  19. Based on the compacted graphite iron castings, the " compacted graphite iron casting quality analysis system " has been developed. it includes three subsystem : the casting defects knowledge consultation, the casting quality data control and analysis, the casting defects qualitative analysis and predication

    以蠕墨鑄鐵件為基礎，開發了「蠕墨鑄鐵件質量分析系統」 （ fqas ） ，包括鑄件知識咨詢、鑄件質量數據管理與分析和鑄件質量分析及預測三個子系統。
  20. To increase the rate of hitting the grade of liquid steel based on match between converter and continuos caster in capacity is considered as a promising way to improve process control and make production cost - efficient at steel making division. based on lgmis and the model of process - control of converters, the factors, which impact to the hit ratio of grade of liquid steel, have been investigated in details. the influence of quality and availability of primary raw materials, such as hot metal, semi - steel and mixture hot metal and semi - steel, on quality of liquid steel has investigated

    本文結合攀鋼轉爐煉鋼工藝現狀及全連鑄對鋼水質量的要求，從改進煉鋼過程質量控制的角度，以轉爐連鑄機爐機匹配條件下提高鋼種煉成率為目標，在現有lgmis系統和轉爐煉鋼過程靜態控制模型的基礎上，詳細分析了攀鋼轉爐煉鋼的鋼種煉成率以及影響攀鋼轉爐煉鋼的鋼種煉成率的因素，分析了轉爐煉鋼主原料（鐵水、半鋼、混合鐵水）的質量和物流條件對攀鋼煉鋼過程質量的影響，提出了通過控制轉爐煉鋼主原料質量和物流條件改進煉鋼過程質量控制的策略。
分享友人
分享到 Line

分享到臉書