鑄態組織 的英文怎麼說

中文拼音 [zhùtàizǔzhī]
鑄態組織 英文
as cast structure
  • 鑄 : Ⅰ動詞（鑄造） cast; coin; make Ⅱ名詞1. （古國名） zhu, a state in the zhou dynasty2. （姓氏） a surname
  • 態 : 名詞1. （形狀; 狀態） form; condition; appearance 2. [物理學] （物質結構的狀態或階段） state 3. [語言學] （一種語法范疇） voice
  • 組 : Ⅰ名詞1 （由不多的人員組成的單位） group 2 （姓氏） a surname Ⅱ動詞（組織） organize; form Ⅲ量詞（...
  • 織 : 動詞（編織） knit; weave
  • 組織 : 1 （組織系統） organization; organized system 2 （組成） organize; form 3 [紡織] weave 4 [醫學] [...
  1. In fact in the die casting process, when the liquid metal have not solidified completely, in order to break arborescent structures which have already solidified and then proceed fine - crystal intensification, we apply a deforming force, so the mechanical properties of parts produced by liquid combination process of die casting and forging will be improved significantly

    其實質就是在壓鑄基礎上，待型腔中的液態金屬還沒有完全凝固時，立即施加一個變形力，打碎已經凝固的枝晶組織。鑄鍛雙控成形工藝主要適合生產形狀復雜和強度要求高的汽車零部件和其它結構件。
  2. By analyzing the microstructure of as - cast alloys with different surplus of samarium added, the optimum surplus of samarium is decided. by comparing the microstructure of the alloys annealed for different time, the ideal and economical annealing time is confirmed. the microstructure and phase composition of alloys during the whole preparation of sm2fe17nx are analyzed using the scanning electron micrograph with energy - dispersive x - ray analysis and x - ray diffraction patterns

    本論文首先就熔煉工藝參數對鑄態組織微結構的影響進行了探討，並制定出一套較為合適的熔煉工藝；通過對不同釤加入量的鑄態組織微觀結構的觀察分析，確定了原料配置過程中釤的最佳補償量；通過對採用不同退火時間的合金組織進行比較，確定了理想、經濟的退火時間；同時還利用掃描電子顯微圖像和x射線衍射圖譜，比較了整個制備過程中，試樣微結構和相組成的變化情況。
  3. When the atomic ratio of nb is one, the structure is homogeneous and almost composed of the single sm2fe17 phase. it ' s nearly the same structure as that after annealing. so it can reduce the production cost and increase the stability of magnetic properties

    當nb的原子比為1時的鑄態組織基本為均勻的接近單相的sm _ 2fe _ （ 17 ）組織，已接近於退火后的組織，從而可以避免冗長的均勻化退火化過程而直接用於製造永磁體，極大的降低了生產成本，並能有效的提高磁性能的穩定性。
  4. The results indicate that the fracture toughness is influenced markedly by the different base structure of vermicular east iron and by the form of graphite ; unlike steel, the fracture toughness of vermicular cast iron increases with the yielding strength, while drops drastically with the increase of ratio of graphite grain length to thickness

    試驗結果表明，蠕墨鑄鐵的斷裂韌度受不同基體組織的影響比較明顯；受不同石墨形態的影響顯著，與結構鋼不同，蠕墨鑄鐵的斷裂韌度隨材料的屈服強度增大而增大，隨石墨顆粒的長厚比增加會急劇下降。
  5. Production and control of internal stress in grinding balls of high chromium white cast iron

    淺析低鉻白口鑄鐵磨球的鑄態組織設計
  6. Abstract : in this study, 2618 aluminum alloy manufactured by spray process was heated in a heating furnace, and the microstructures were investigated. by the process of heating in a heating furnace and then squeeze - forming, one component of the motorcycle was produced successfully with the semi - solid aluminum alloy

    文摘:採用電阻爐加熱的方法對噴射沉積法制備的2618鋁合金進行了二次加熱實驗，觀察了顯微組織的變化；並通過電阻爐加熱、半固態擠壓鑄造的方法成功地試制了摩托車零件。
  7. Primary analyses of cast microstructure design of high chrome white cast iron grinding ball

    淺析高鉻白口鑄鐵磨球的鑄態組織設計
  8. The effect of the melting - current and melting - time on the microstructure of the as - cast sm - fe alloy is investigated and the phase composition of the as - cast sm - fe alloy with different sm content is analyzed. the parameters of the melting process and the proportion between different chemical elements are decided, which are based on the above - mentioned investigation and analysis

    實驗中研究了不同熔煉電流和熔煉時間對鑄態組織的影響，並對不同含量的sm - fe合金退火前後的相組成進行了分析，在此基礎上確定了熔煉參數和成分配比。
  9. In the research case of 11 tapping during night shift on december 31, 2000, optimized schedule strategy can cut down 65 minutes at most used for processing from charging into converter to slab out of caster for each tapping. with the model, it is possible to dynamically adjust schedule and reorder or reorganize production process

    以煉鋼廠2000年12月31日中班11爐連鑄鋼的生產調度計劃為例，利用模擬模型制定和優化的調度計劃使鋼水從煉鋼到連鑄的作業時間最大可以節約65分鐘；利用煉鋼連鑄生產調度時間petri網模型，還可以根據實際生產條件的變化（譬如設備故障）對生產進行動態調整，以方便組織生產。
  10. The phase composition and microstructure of sm - fe - zr alloy with different amount of zr are analyzed and the effect of zr content on the microstructure of as - cast sm - fe - zr alloy is studied. the results indicate that microstructure of as - cast sm - fe - zr alloy is improved obviously with 1. 0at % zr added, and that the long - time high temperature homogenization is unnecessary for the alloys with this microstructure. by this way, the purpose of the research to decrease the cost of preparation and optimize process is achieved

    分析了不同zr含量的sm - fe - zr合金的相組成和微結構，研究了zr含量對鑄態組織的影響，結果表明，添加1 . 0at的zr可以明顯改善合金的鑄態組織，從而可以避免昂長的高溫均勻化退火過程，取得了降低製造成本和優化工藝的效果。
  11. The amount of nb3si / nb5si3 increases, their morphology tends to be more regular, their distribution becomes more homogeneously with the increasing of withdrawing rate. the microstructure is better oriented along the longitudinal axis of the samples when the withdrawing rate is between 0. 6 and 6. 0mm / min. at the same withdrawing rate, the microstructure changes from the beginning part to the ending part of the samples

    鈮?硅基rmics材料原始鑄態組織由初生nb基固溶體和在其間分佈的nb基固溶體+硅化鈮共晶團組成；隨著抽拉速率的增大，定向凝固共晶組織中硅化鈮強化相細化、數量增多、分佈趨于規則和均勻，定向效果顯著；在相同抽拉速率條件下，區熔試樣的組織從起始段到終止段發生了改變。
  12. The results showed that the in - situ formed tibi particles which had a size of about 50nm, exhibited a homogenous dispersion in the copper matrix. moreover, the interface between the nanoscale particles and the copper matrix was clean, and there was no certain location relationship. due to their reinforcement, the tensile strength and hardness of the in - situ cu - tib _ 2 nanocomposite significantly improved

    通過光學顯微鏡、 tem 、 xrd等對cu - tib2原位復合材料進行了金相組織、微結構分析，原位復合材料的鑄態金相組織中彌散分佈著團簇狀的tib2顆粒；形變態金相組織中tib2顆粒呈纖維狀排列； tem觀察表明：在基體內存在著尺寸約為50nm 、彌散分佈的tib2顆粒，且tib2顆粒與基體之間界面清晰，但由於tib2結構與銅晶體結構的差別較大， tib2顆粒與基體之間無固定的位向關系；納米tib對銅基體有良好的增強作用。
  13. Effect of co on as - cast microstructure of al - 5 fe alloy

    合金鑄態組織的影響
  14. Casting - state structure

    鑄態組織
  15. Pure rare earth elements, lanthanum and cerium, are added to pure copper, then the inner mechanism and influence of rare earth addition on its absorptivity in copper casting microstructure specific resistance and mechanical properties are studied in this paper

    在純銅中加入純稀土元素la 、 ce ，研究稀土元素在純銅中的作用機理、吸收率的影響因素以及稀土元素對鑄態組織、導電性、力學性能的影響。
  16. Through analyzing the phase composition and microstructure of sm2fe17 - xnbx alloys ( x = 0. 5, 1, 2, 3 ), we study the influence of the addition of element nb on the microstructure of sm2fe17 alloys. the results show that the as - cast structure of sm2fe17 - xnbx alloys can be improved effectively

    本文重點研究了添加過渡族nb元素對sm - fe合金相組成和微結構的影響，實驗研究發現：添加微量的nb元素可以有效的改善sm - fe合金鑄態組織的顯微結構。
  17. The welding line microstructure of ticp / fe in situ composites gained by different welding technologies and welding methods was different. however the microstructure was diffused on the welding line and there were no welding defects, the welding quality was better. the tic reinforced particles on the welding line still kept the same shape as that of the casting microstructure

    原位tic _ p fe復合材料採用不同焊接工藝和焊接方法所得的焊縫組織有所差別，但焊縫處的組織均勻，沒有裂紋等焊接缺陷產生，可焊性較好；焊縫處的tic增強顆粒仍保持鑄態組織中tic增強顆粒的形態。
  18. The microstructure, the hardness and the wear resistance properties of the composites fabricated by semi - solid casting has been studied and analyzed metallographic analysis indicated that sic particles dispersed uniformly in the composites

    本文採用半固態復合鑄造法制備了sic顆粒增強鋁基復合材料，並對這一系列材料的微觀組織、硬度及耐磨性能進行了研究與分析。
  19. A series of nickel - chromium - copper cast - irons with varied rare earth were designed and theirs microstructures were observed by optical election microscope ， the corrosion rates of re - ni - cr - cu alloy cast irons in static 、 room ? temperature and strong alkali liquor were measured by the hydrometer method

    設計了含不同量的稀土鎳-鉻-銅合金鑄鐵，採用光學顯微鏡觀察組織，用失重法測定合金鑄鐵在靜態、室溫、高濃度堿液中的腐蝕速率。
  20. Abstract : this paper summarized the present study status of the semi - solid casting technology in the following aspects : basic theory study ( the rheological behavior and the microstructural characteristics of semi - solid alloys ), modeling of the semi - solid forming process, raw material production, property and industrial applications

    文摘:論述了半固態鑄造技術的基礎理論研究（半固態合金流變行為及其微觀組織特徵） 、半固態鑄造合金成形過程的數值模擬、半固態鑄造原材料的制備工藝、性能及工業應用現狀。
分享友人
分享到 Line

分享到臉書