鑄造成的 的英文怎麼說

中文拼音 [zhùzàochéngde]
鑄造成的 英文
fluid origin
  • 鑄 : Ⅰ動詞（鑄造） cast; coin; make Ⅱ名詞1. （古國名） zhu, a state in the zhou dynasty2. （姓氏） a surname
  • 造 : Ⅰ動詞1 （做; 製作） make; build; create; produce 2 （假編） cook up; fabricate; concoct 3 [書面語...
  • 成 : Ⅰ動詞1 （完成; 成功） accomplish; succeed 2 （成為; 變為） become; turn into 3 （成全） help comp...
  • 的 : 4次方是 The fourth power of 2 is direction
  • 鑄造 : [冶金學] cast-on outwell; foundry; cast; casting; found; founding
  1. The operation principle and device to produce acetin and hydroxyethyl acetate for foundry firming agent were analyzed in the paper, and the choice of esterification catalyst and dehydrated agent in the esterifying process also were analyzed theoretically, and finally, the better producing operation device, catalyst and dehydrated agent were obtained

    摘要分析了鑄造用有機酯固化劑酯酸甘油酯和乙二醇醋酸酯合成工藝原理及裝置，同時對有機酯合成工藝條件中脫水劑和催化劑的選擇的理論依據進行了分析，得出鑄造用有機酯固化劑的最佳合成工藝裝置和脫水劑、催化劑。
  2. Some other defects in castings are well - defined cracks and hot tears that develop during solidification, under combination of stress concentration from uneven contraction and the metal ' s low strength at near - melting temperatures

    鑄件內部的其它一些缺點是，凝固過程中，在不均勻收縮造成的應力集中和接近熔點溫度下金屬的低強度的綜合作用下，出現的清晰裂縫和熱撕裂。
  3. Henrik ibsen says, " it ' s your supreme duty to cast yourself into a useful implement.

    易卜生說： "你的最大責任是把你這塊材料鑄造成器。
  4. As a matter of fact, the early seigniorage was the balance that the coin minter got after the mintage cost was subtracted from the expense that coin buyers paid

    早期的鑄幣稅實際上是鑄幣者向購買鑄幣的人收取的費用在扣除加工鑄造成本后的余額。
  5. Rapid prototyping technology changed the traditional pattern of product design, which could offer product sample for the designer, reduced design cycle and quicken the schedule of new product design, and it gave the decision - makers visual feeling. ; rp technology provided kinds of molds including resin - boncled mold laminate mold, investment mold and lost foam casting mold and so on for sand casting investment casting and cavityless casting, it could also use direct shell production casting to make pattern dies metal dies die - casting dies injection dies directly, and it could even produce casting products in small scales. the applications of fdm technology in plaster precision casting and the rapid casting technology based on sls technology were introduced, the organic combination between rapid prototyping tecnnology and foundry process, which initiated a new period of rapid manufacturing metal parts, by using advanced new technology alternated traditional foundry industry to make it looked brand - new, thus, the competition of foundry industry would be improved ; rapid prototyping technology offered a rapid economical feasible technical method, common processes of using rapid prototyping technology to produce dies were discussed, in the paper it explored that. the problem of combining rapid prototyping technology with electric arc metal - spraying technology to make metal dies and technics in dies manufacturing of combining rapid prototyping technology with precision casting, rapid tooling based on rapid prototyping, integrated advanced new technology and tradition technology of rapid prototyping manufacture, each superiority were exerted, rapid prototyping technology had been an efficiency measure to rapid update products and develop new product, and to middle -

    快速成型技術改變了傳統的產品開發模式，可以為設計者提供產品樣件，縮短設計周期，加快新產品的開發進度，為決策者提供直觀性；快速成型技術迅速提供砂型鑄造、熔模鑄造、實型鑄造用的各種模樣，包括樹脂模、層壓模、熔模和消失模等，還可採用直接制殼鑄造法直接製造熔模鑄造用的壓型、金屬型、壓鑄型、注塑模，甚至直接製造小批量鑄件，介紹了熔積成型技術在石膏型精密鑄造上的應用和基於選擇性激光燒結技術的快速鑄造技術，快速成型技術與鑄造工藝的有機結合，開創了快速製造金屬零件的新階段，對用高新技術改造傳統的鑄造工業，使其面貌煥然一新，增強鑄造行業的競爭能力；快速成型技術為母模的製造提供了一條快速、經濟、可行的技術途徑，討論了利用快速成型技術製造模具的一般工藝方法，探討了將快速成型技術與金屬電弧噴鍍技術結合起來快速製造金屬模具問題，以及快速成型技術與精密鑄造技術相結合的模具製造工藝，基於快速成型製造的快速模具技術，集成了快速成型製造高新技術和傳統技術，發揮各自優勢，已成為產品快速更新換代和新產品開發及中、小批量生產的有效手段之一。
  6. Colleagues from foundry industry are welcome to visit our company to improve our understanding with each other, and we are looking forward to having you as our long - term cooperating partner

    歡迎鑄造業的同行來我公司參觀指導，加深彼此間的了解，並期待著成為您長期的合作夥伴。
  7. The heat expansion coefficient of casting nylon materials is about 10 times larger than steel, so the internal dia shrinks caused by the expansion. it will influence the connection gap of the abrasive surface

    鑄型尼材料的熱膨脹系數約比鋼材大10倍左右，所以軸套在運行時由於摩擦熱所造成的膨脹變形使內徑縮小，影響摩擦面的配合間隙。
  8. Abstract : this paper states a method of substituting forge welding the blank of shelf for casting it. it is on the individual spare parts and small batch production in order to reach low cost and high efficiency

    文摘:主要闡述在單件、小批量生產情況下，對採煤機機殼毛坯用鍛焊結合的方法成形代替傳統的鑄造成形方法，以達到生產的低成本、高效率的目的。
  9. With high strength, low density, good castability and machineability, al - si series cast alloy has become one of the most important structural materials in manufacturing industry, and zl101a is the most widely used

    鑄造鋁硅合金具有容重小、比強度高、鑄造成形性和加工性能好等優點，已成為製造行業中最受重視的結構材料之一，該類合金中的zl101a應用最為廣泛。
  10. Could you break down casting cost on material cost and the rest of cost and present calculation for material cost

    請你將鑄造成本按照材料成本和其他成本進行分項記錄並提供材料成本是如何計算的。
  11. Restoration revealed that the sculptor had finished his creation carefully, patching small defects created by air bubbles trapped in the original casting

    修復物揭示雕像家在完成他的創作時極其認真。他把第一次鑄造時產生的氣泡造成的瑕疵?一修補完好。
  12. Because cast steel can be made to suit almost any geometry, it makes for a gradual and elegant architectural transition between individual structural members

    因為鑄鐵可以鑄造成幾乎任何的幾何形狀這使得獨立構件間的建築上的過渡變得緩和、優美。
  13. Believed to be the first use of cast steel for railway bridge structures in germany ? and perhaps the world ? the viaduct ' s cast steel connections underwent substantial testing to determine their static and dynamic behavior

    因為鑄鐵可以鑄造成幾乎任何的幾何形狀這使得獨立構件間的建築上的過渡變得緩和、優美。
  14. When the data of logistics in current process are used for input of simulating logistics in future 100 % continuous casting process, supply of hot metal from iron - making process may not satisfy the needs of 100 % continuous casting on raw materials. because planning scheme in continuous casting process depends greatly on smelting scheme in convertor vessel, it is important for operator to balance raw materials supply, smelting and casting in order to realize the scheme of 100 % continuous casting. when some equipment are work abnormally, mixer of hot metal and lf furnace can be used for logistics buffer

    用攀鋼煉鋼生產數據對模擬軟體系統進行的測試和模擬研究結果表明：模擬系統的隨機數發生演算法可以實現對作業時間的依分佈隨機抽取；在相似的輸入條件下，模擬結果與實際生產物流的時間分佈規律基本吻合，達到了模擬軟體設計的預期目標；若以攀鋼提釩煉鋼廠現工藝的鐵水輸入作為全連鑄后的輸入條件，則現工藝的物料供應能力可能難以滿足全連鑄生產的要求；連鑄機的連澆計劃對轉爐爐次計劃的編制有很高的要求，合理安排來料、煉鋼與澆鑄三者間的物流平衡關系將是保證全連鑄作業的重要條件；當出現設備異常情況時，可以利用混鐵爐與lf爐站前等待作為物流緩沖池，通過延長系統的平均物流時間來緩解因設備檢修和故障等擾動所造成的影響，確保生產的順利進行。
  15. Any can apply for to all gold casting cause gold coin or become its metallic piece gold coin dissolve to national mint

    任何都可以向國家造幣廠申請將其所有的黃金鑄造成金幣或將金幣溶成金屬塊。
  16. Dimensional uniformity of closed - die forgings results in positive control of critical wall thickness, eliminating deficiencies caused by shifted cores in castings

    閉模鍛造的尺寸一致性造成關鍵壁厚的完全控制，避免了鑄造工藝中鐵心移位造成的缺陷。
  17. The specimens showing profuse branching of vessels and ducts in colour were prepared by a corrosion casting method

    這些標本展示了色彩豐富的血管和導管分支，是通過腐蝕鑄型技術造成的。
  18. By means of mechanical properties determination, optic and electronic microscope examination and practical application it is verified that the usage of cap type filter could improve steel casting properties and effectively reduce inclusive cast defects in investment casting

    通過測定鑄鋼試樣的力學性能、進行金相分析、電子顯微分析和生產應用，驗證了採用熔模鑄造帽式過濾器能改善鑄鋼性能、有效減少精鑄件由於夾雜所造成的廢品。
  19. And, we will bring the same determination and commitment to making yec a preferred supplier to all of our global customers

    同時，我們將以同樣的決心和承諾將合資公司鑄造成為我們全球客戶的優選供應商。
  20. Next, the virtual model is cast into a new foam model, using the dimensions of the cad model

    其次，虛擬模型是鑄造成一個新的泡沫模型，用尺寸的cad模型。
分享友人
分享到 Line

分享到臉書