閉鎖位置 的英文怎麼說

中文拼音 [suǒwèizhì]
閉鎖位置 英文
locked position of coupler
  • : Ⅰ動詞1. (關; 合) close; shut 2. (堵塞不通) block up; obstruct; stop up Ⅱ名詞(姓氏) a surname
  • : Ⅰ名詞1 (安在開合處使人不能隨便打開的器具) lock 2 (姓氏) a surname Ⅱ動詞1 (上鎖) lock up 2 ...
  • : Ⅰ名詞1 (所在或所佔的地方) place; location 2 (職位; 地位) position; post; status 3 (特指皇帝...
  • : 動詞1. (擱; 放) place; put; lay 2. (設立; 布置) set up; establish; arrange; fix up 3. (購置) buy; purchase
  • 閉鎖 : shutting; bottoming; interlock; rejection; latching; paralysis; clausura
  1. In this paper, a safe, reliable, and intellectual control plan is provided aiming at the heat charge for dwelling district, which contains epigynous machine responsible for data processing and hypogynous mahcine responsible for unlocking the valve, by means of serial communication between them, combining homemade three - channel valve, to adminstrate the charge data and the valve efficiently. the main idea is based on the homemade three - channel valve. the vavle is locked at peacetime, while it is opened with the help of open tool and a water flow in the caliduct. as soon as the flow stops, the valve locks automatically. the open tool has data in its memory, and implement function by lcd and keyborad. so it can identify data and drive motor, to open the valve intellectually. the epigynous machine database manage system administrator the dweller information, standard heat charge and payment infomation etc, including store, configure, query, print etc, then store in the memory of open tool. as a result, the plan can do well in the experiment

    此閥平時是的,只有用開啟器配以暖氣片中的水流才可打開,一旦水流斷開,則此閥會自會。而開啟器則是根據其存儲器中的數據配以液晶顯示及小鍵盤,完成數據確認及電機驅動,自動對相應用戶的三通閥打開特定角度,完成開啟任務。上機數據庫管理系統完成對用戶信息、熱費標準、繳費信息等原始數據的常規管理,包括存儲、設、查詢、列印等,最後將處理后的數據傳到開啟器中存儲。
  2. In this paper, firstly the macro parameter of the series connection app was comprehensively analyzed, among which the trajectory location of the bullet emission and the terminal velocity of the bullet were mainly analyzed, and the feasibility of the series connection app to cope with explosive reactive armor was demonstrated. and then the macro design about the head of the series connection app was made, among which a particular analyse about the bullet " s launching process was made, from which we concluded the relation between the thickness of the airproof loop and the velocity of the bullet detached from the carrier and the relation between the length of the bullet and the velocity of the bullet detached from the carrier and the relation between the length of the bullet and the burning rate of the powder and the relation between the length of the bullet and the maximum pressure of the emission hole and the relation between the length of the bullet and the emitting time of the bullet, and the reasonable str ucture of the head of the carrier and bullet were designed, then the intensity of the head of the carrier was checked out using of the software of ansys

    本文首先對子母式穿甲彈總體參量作了全面的計算分析,其中主要分析了子彈射出的彈道和必要的子彈著靶速度,論證了子母式穿甲彈對付爆炸式反應裝甲的可行性,然後對子母式穿甲彈彈頭部進行了總體設計,其中主要對子彈的發射過程進行了詳細的分析,得出了母彈彈頭部發射孔內環厚度與子彈飛離母彈速度的關系、子彈長度與子彈飛離母彈速度的關系、子彈長度與火藥燃燒率的關系、子彈長度與母彈彈頭部發射孔內最大壓力的關系以及子彈的長度與子彈發射所需時間的關系,設計出了合理的母彈彈頭部結構和子彈的結構,並利用ansys有限元分析軟體對母彈彈頭部的強度進行了校核。
  3. Position the two halves of the flange adapter onto the groove in the valve body end ( s ), making sure that the tab on each flange adapter half is located between the two locking lugs on the valve body ( fig. 3a )

    將法蘭適配器的兩半放在閥體連接埠的溝槽上,確保每個半邊法蘭適配器上的孔於閥體上兩個凸榫上(圖3a ) 。
  4. Since latching relays do not require current flow to maintain position, they are used in applications with limited power

    由於繼電器不需要電流來維持其,因此被用於功率有限的應用中。
  5. Close the back cover so that the back cover latch snaps shut and returns t the original position

    關上后蓋,使后蓋迅速關,回到原來
  6. Rotate the valve to [ close ] position, put in the valve and install screw, nut and washer, then, tighten them up with hand

    將閥門轉到關,將閥門放入,安裝螺絲,螺母及華司,然後用手緊。
  7. This all - plastic kit, permanently mounted on a valve, may be locked in the on or off valve position

    這種全塑料組件永久性安裝在閥門上,可能被定在閥門開啟或關上。
分享友人