間隙公差 的英文怎麼說
中文拼音 [jiānxìgōngchā]
間隙公差
英文
clearance allowance- 間 : 間Ⅰ名詞1 (中間) between; among 2 (一定的空間或時間里) with a definite time or space 3 (一間...
- 隙 : 名詞1 (縫隙; 裂縫) crack; chink; crevice 2 (空閑) gap; interval 3 (漏洞; 機會) loophole; op...
- 公 : Ⅰ形容詞1 (屬于國家或集體的) state owned; collective; public 2 (共同的;大家承認的) common; gen...
- 差 : 差Ⅰ名詞1 (不相同; 不相合) difference; dissimilarity 2 (差錯) mistake 3 [數學] (差數) differ...
- 間隙 : (空隙) interval; gap; freedom; space; [機械工程] clearance; separation; stricture; clear; inter...
-
Based on the fact of driven gear moving prior to normal locality when driving gear pair moving from upper dead center to lower dead center, considering all influential elements, the maximum backlash of gear pair can be controlled to satisfy the special driving requirement through controlling the length and deviation of its common normal without increasing its manufacture precision
摘要根據換向傳動齒輪副從上止點向下止點運動時被動齒輪運動超前的實際,從影響齒輪副側隙的各種因素出發,在不提高齒輪副製造精度的前提下,通過拉制齒輪副公法線長度及其偏差從而有效地控制齒輪副的最大齒側間隙,以滿足傳動的特殊要求。Analyze item by item the position of unintact cycle, the running clearance of unintact cycle, locking - deform, datum dimension regulating, repeatly install, power voltage wave and marking running etc. at the same time, we give the calculating formula to calculating the running marking random error, and use it to calculate the system error of big diameter measure instrument - - datum dimension frame error, gyro - wheel diameter error, error caused by circumstance temperature, error caused by backing distance, angle error, delay error of data collecting circuit, lathe main shaft running error, workpiece install partial error
對不完整圓的位置、不完整圓的轉動間隙、鎖緊變形、基準尺調整、重復安裝、電源電壓波動、標記轉動等隨機誤差進行了逐項分析,並給出轉動標記隨機誤差的計算公式。對大直徑測量儀的系統誤差?基準尺尺架誤差、滾輪直徑誤差、環境溫度引起的誤差、後退距離引起的誤差、角度誤差、數據採集電路延時誤差、車床主軸回轉誤差、工件安裝偏心誤差分別進行了計算,最後對誤差進行合成。Ball bearings, conrad type, for electrical machines ; tolerances and radial clearance
電氣機械用的連桿式球軸承.公差和徑向間隙Iso - fits for the hole basic system ; tolerances of fit clearances and interferences
基孔制配合.配合公差間隙和過盈Iso - fits for the shaft basis system ; tolerances of fit clearances and interferences
基軸制配合.配合公差.間隙和過盈Circular metal slitting saw blades ; tooth forms, side clearance, manufacturing tolerances
金屬用開槽圓盤鋸片.齒形側面間隙製造公差Railway material in general. recommended tolerances and fittings - general case. fittings with clearances
鐵路通用器材.推薦公差和配合.一般情況.間隙配合Rolling bearings : tolerances - specifications for radial internal clearance
滾動軸承.公差.第3部分:徑向內部間隙規范Rolling bearings - rolling bearing tolerances - part 4 : radial internal clearance
滾動軸承.滾動軸承公差.第4部分:徑向內間隙Railway material in general. tolerances and fittings used, particularly, for articulations. fittings with clearances
通用鐵路設備.鉸接用特殊公差與配合.間隙配合分享友人