閥板 的英文怎麼說
中文拼音 [fábǎn]
閥板
英文
ale deck plate-
When the moment made by material on turning plate is greater than that of heavy hammer and rocker, the disc will open adown to discharge
當作用於翻板上的物料產生的力矩大於重錘搖桿產生的力矩時,閥板打開向下卸灰。Valve deck plate type piston pump
閥板式活塞泵The disc sealing ring is easy to replace and maintain
閥板密封圈易於更換,便於維修。Non - preferred would try to push the disc away from the seat while it is in the closed position
非優先定向則當閥門處于關閉狀態時,試圖將閥板推離閥座。Sweden transheater in sweden afla valve style
換熱器採用瑞典阿法拉閥板式換熱器。Disc is free to rotate to prevent localized wear
閥板旋轉自如,避免定位磨損。A valve shuttered electronic expansion valve
閥板式電子膨脹閥研究One - piece thru shaft : ensures dependability and positive disc positioning
一體化貫穿軸:確保閥門的強度、可靠性合閥板的精確定位。The use of the double eccentric structure in the butterfly plate so as to the horizontal valve shaft is lifted a little distance above the pipe central line, and it makes that the area of lower half part butterfly plate is bigger than upper part
該閥採用雙便心閥板,水平安裝的閥軸在管道中心線上抬高一定距離,使閥板下半部分迎水面積大於上半部。The paper introduced the welding repair process for the sealing surface of high - pressure valve board. it greatly improved the inlet high - pressure valves service life and obtained better economy benefits.
介紹了高壓閥閥板密封面焊接修復的過程,經實際使用證明,該工藝方法行之有效,提高了進口高壓閥的使用壽命,取得了較好的經濟效益。The cylindrical pin prevents a horizontal displacement of disc
筒形銷防止閥板的水平位移。After discharge the moment made by heavy hammer and rocker will drive disc close quickly to realize locking air
一旦積灰卸去后,重錘與搖桿產生的力矩使閥板迅速關閉,實現鎖氣。3 the valve body and disc of valve shall be made of ductile cast iron
閥門的閥體、閥板製造材料應該是球墨鑄鐵。" t " structure of disc sealing ring. the sealing pair is linear sealing
閥板密封圈採用" t "形結構,密封副呈線性密封。Instead, the motor rotate reversely, push rod ( piston rod ) push out, the valve plate closes, stops discharging
反之,電機反轉,推桿(活塞桿)推出,閥板關閉,停止卸料。Valve plate type piston pump
閥板式活塞泵The swing check to stop reverse - flow is moounted in the disc - lever with little axial and radial play and held by screw nuts
用來阻止逆流的旋啟式止回閥是安裝在閥板拉桿上,有微小的軸向和徑向活動間隙,並用調節螺母固定。It specifies the process of the design, simulation and experiment of liquid cooling system. main contents of the thesis are as follows : description of the present usage of liquid cooling system, presentation of a new type of liquid cooling system and description of its work principles ; design of the liquid cooling system, which mainly deals with the design and collating calculating of serpentine condenser and heat exchangers adopted in this system. meanwhile, the model chosen calculating of compressor 、 thermal expansion valve 、 plate evaporator 、 water pump and the like equipment used in the system are also carried out
本文的主要內容如下:對液冷源使用現狀進行了描述,提出了一種新型液冷源系統並對其工作原理進行了闡述;對系統進行了設計,主要對系統中所採用的管帶式冷凝器和水側空/液換熱器進行了設計和校核計算,同時對系統中所用到的壓縮機、熱力膨脹閥、板式蒸發器、水泵等配套設備進行了選型計算;分別對製冷系統和冷卻液循環系統進行了數學建模。After tightening, the screw is secured and presses the disc firmly against the four - parted thrust ring thus protecting against slipping
在上緊后,螺絲可靠地把閥板壓在由四部件組成的止推環上,防止滑。Thermal exchanger has applied afla valve plate type thermal exchanger from sweden
換熱器採用瑞典阿法拉閥板式換熱器。分享友人