限度極限 的英文怎麼說

中文拼音 [xiàndùjíxiàn]
限度極限 英文
limit
  • 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 極 : i 名詞1 （頂點; 盡頭） the utmost point; extreme 2 （地球的南北兩端; 磁體的兩端; 電源或電器上電流...
  • 限度 : limit; limitation; measure; tether
  • 極限 : 1 （最高的限度） the limit; the maximum; the ultimate limit; limitation; extremity; tipping point...
  1. Have you ever felt like you are at your breaking point

    是否有過已經處在強度極限的感覺？
  2. The consequence is, when the majority of structure does n ' t enter yield habitus, but the position of belly - board has been reached the ultimate habitus, it lead to material waste of the other positions, we should pay attention to the disastrous result it will bright to us

    它帶來的後果就是當結構的大部分處于彈性狀態時，箱梁腹板處由於剪力滯效應一般最先達到強度極限狀態，導致腹板間材料的抗力沒有得到充分的使用，如不引起重視會帶來災難性後果。
  3. Accuracy limit factor of a protective current transformer

    保護用電流互感器的精確度極限因數
  4. Plasma ignition for engine is a new pattern portfire, it firstly lights up the start - up oil and form ignition torch to ignite the main oli in the combustor. lt is a new technolygy, at the present only ukraine have used this technique in marine gas turbine and the ground gas turbine to increase the reliability of retro fires and extend the concentration limit of retro fires

    等離子點火技術是一門新興技術，目前只有烏克蘭將該技術應用到了艦船燃氣輪機和地面燃氣輪機上，由於該項技術主要點火設備具有獨特的放電特性和較大的放電能量，並且能量集中，使發動機的點火可靠性和點火的濃度極限得到了極大的提高。
  5. Taking the contact stress, bend stress stiffness and temperature stress as the condition, taking the weight of the kiln tyre as optimization aim function, the redia and the width of the tyre are optimized general optimize methods just consider the affecting of the parameters to aim function, but in fact, structural parameters ( such as structure dimension, interval and so on ), physics and dynamics ( damp factor, conduct factor, friction factor material ' s elastic module strength limits and so on ), which would be changed after used. the difference are called discrepancy robust design ' s basic concept is : all design parameters " discrepancy will affect the aim funct ion and arouse the quality target discrepancy

    一般的優化方法，僅僅考慮了參數對其目標函數的影響，而實際情況下有些參數是變化的，產品的結構參數（如幾何尺寸、間隙等） 、物理和力學參數如阻尼系數、傳導系數、磨擦系數、材料的彈性模量和強度極限等的設計值與製造后和使用中的實際值會有差異，這種差異稱為設計變量和噪聲因素的變差。
  6. The speed of light turns out to be nature's speed limit.

    光速原來是自然界的速度極限。
  7. Safety of machinery. temperatures of touchable surfaces. ergonomics data to establish temperatur limit values for hot surfaces

    機械的安全性.可觸摸表面的溫度.確定熱表面溫度極限值的人機工效學數據
  8. Relations between the fractal dimensions of tensile fractures and the tensile ultimate stresses for the grain composite material caco3 abs

    拉伸斷口表面分形維數與其拉伸強度極限的關系
  9. Critical height analysis for bedding rock slopes using the upper - bound method of limit analysis

    層狀巖質邊坡臨界高度極限分析上限解
  10. Because most people live in the oasis, the oasis population density gets the 169. 47, higher than the chinese average standard ( 129. 4 ). under the condition of bad exist environment and limited exist resources, more population means it is difficult to get rid of poverty. population number becomes one of most importane factors to deteriorate the arid poverty

    而和田人口密度（ 10 . 27人/平方公里）遠大於乾旱區人口密度極限（ 7人/平方公里） ，由於人口都集中在綠洲，綠洲的人口密度（ 169 . 47人/平方公里）超過全國平均水平（ 129 . 4人/平方公里） ，由此，在生態環境惡劣、生存資料有限的情況下，和田人口數量過多使其更難以擺脫貧困，人口數量成為加劇乾旱區貧困的基本因子之一。
  11. Determination of time - temperature limits for plasties after prolonged exposure to heat

    塑料長期熱暴露后時間-溫度極限的測定
  12. Plastics - determination of time - temperature limits after prolonged exposure to heat

    塑料製品.熱力長期幅照后時間溫度極限的測定
  13. Plastics. determination of time - temperature limits after prolonged exposure to heat

    塑料製品.長時間受熱后時間-溫度極限值的測定
  14. Plastics - determination of the time - temperature limits after prolonged exposure to heat

    塑料.長期暴露于熱作用后時間和溫度極限值的測定
  15. General principles for temperature limits in the rating of electric equipment and for the evaluation of electrical insulation

    電子設備額定值中溫度極限和電絕緣評定的一般原則
  16. General principles for temperature limits in the rating of electrical equipment and for the evaluation of electrical insulation

    電子設備額定值中溫度極限和電絕緣評定的一般原則
  17. The limit using temperature of mc nylon is 120, the gear can t work correctly if the temperature exceeds 120

    Mc尼的使用溫度極限約120 ，當摩擦熱引起的溫度上升超過此極限時，輪將無
  18. Temperature and pressure limitations for piping systems manufactured from 20 % nickel 2 % chromium spheroidal graphite austenitic cast iron '

    鎳和鉻奧氏體球墨合金鑄鐵制管道系統的壓力和溫度極限
  19. The stress of slag rests with the structure, physical characteristic, and heat transfer status of slag. taking no. 1 boiler of beilun thermal power plant as example, the walltube thermal stress and the destroying impact on slag are researched

    得出鍋爐大范圍變負荷運行時熱應力能夠超過渣的強度極限引起渣結構破壞的結論，渣層的熱應力主要取決于渣的結構、物理特性和傳熱狀態。
  20. Integrated circuits require less power and lower voltages than the equivalent macroscopic circuits, consequently they operate at lower temperatures, and individual components may be closed together without exceeding the operating temperature limit

    參考譯文：集成電路比等效的分離元件電路功率小，工作電壓低，因而可以在較低的溫度下工作，電路中包含的單個元件可以緊靠在一起而不超過工作溫度極限。
分享友人
分享到 Line

分享到臉書