電流轉移比例 的英文怎麼說
中文拼音 [diànliúzhuǎnyíbǐlì]
電流轉移比例
英文
current-transfer ratio- 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
- 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
- 轉 : 轉構詞成分。
- 移 : Ⅰ動詞1. （移動） move; remove; shift 2. （改變; 變動） change; alter Ⅱ名詞（姓氏） a surname
- 比 : Ⅰ動詞1 （比較; 較量高下、 長短、距離、好壞等） compare; compete; contrast; match; emulate 2 （比...
- 電流 : current; galvanic current; electric current; electricity; current flow電流保護裝置 current protec...
- 轉移 : 1 （改換位置） shift; transfer; divert 2 （改變） change; transform 3 [醫學] （擴散） metastasis;...
- 比例 : 1. （長度上縮小和放大的倍數） scale; scaling 2. （比率） proportion; ratio; proportionality
-
The bias magnetic field of the bias coil driven by bias current and small signal test current, results in the induced signal of the control coil. the terminal voltage of the control coil is detected by the test circuit. then the signal containing the information of rotor displacement is obtained, from which we can get the dc voltage signal proportional to the rotor displacement through half - wave rectification circuit and low pass circuit. this dc signal is put into a pid controller to get the control signal of the rotor displacement
偏置測試電路向偏置線圈輸入偏置電流和小信號測試電流，兩者產生的偏置磁場在控制線圈產生感應信號，檢測電路檢測控制線圈端電壓並提取含有轉子位移信息的電壓信號，該信號經半波整流電路和低通濾波電路后得到與轉子位移成正比例的直流信號，再由pid控制器轉換為轉子位移的控制信號，最後控制信號輸入功放電路產生控制電流，實現閉環控制。This paper analyses the type, function and characteristics of usual proportional control valves and raises a new modificative version in the light of their drawback. that is, basing on the principle of flow amplification and electrical feedback and throughout calculation and analysis on flow closed loop control and pressure flow combination., determination of the minimum controlled pressure difference as well as flow controlling range and structure of main valve and research of the dynamic and static characteristic, the paper puts forward control principle of " flow - load pressure change - displacement revision " and pressure / flow double closed loop, and further expounds that using a proportional controller and a electric mechanical transducer can separately serve the control function of pressure or flow as well as flow pressure combination
本論文分析了目前常用比例閥的類型、功能、特性，並針對其不足提出新的改進方案，即：以流量放大，電反饋兩個原理為基礎，通過對流量閉環控制及壓力流量復合的計算分析、確定上最小控制壓差及流量控制范圍，確定主閥結構、功能特性研究等，提出了「流量? ?負載壓力變化? ?位移修正」的控制原理和壓力流量雙閉環控制原理，並進一步論述了利用一個比例控制器和一個「電?機械轉換器」就可完成獨立的壓力或流量控制功能以及流量壓力復合控制功能。
分享友人