電源供給基礎 的英文怎麼說

中文拼音 [diànyuángōnggěijīchǔ]
電源供給基礎 英文
power-supply basics
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 源 : 名詞1. （水流起頭的地方） source （of a river）; fountainhead 2. （來源） source; cause 3. （姓氏） a surname
  • 供 : 供Ⅰ名詞1 （供品） offerings 2 （口供; 供詞） confession; deposition Ⅱ動詞1 （供奉） lay （offerin...
  • 給 : 給Ⅰ動詞1 （送對方某物; 使對方得到） give; grant 2 （用在動詞后 表示交與 付出） pass; pay 3 （叫; ...
  • 礎 : 名詞（墊在房屋柱子底下的石頭） plinth
  • 電源 : source; current source; electric source; power pack; power supply; power source; source of power ...
  1. The e - commerce is based on internet network and pushing the economic globalization corresponding by the continuous development of computer, network and communication technique. the e - commerce influence on the tax theory and tax system that established on the traditional business deeply, involving vat, business tax, income tax for both enterprise and individual, tariff, stamp tax, etc because of the dummy, digital and confusable characteristic contrasting to the traditional business. and it also contributes to our economy development and tax base enlargement

    電子商務會給商家帶來巨大的發展機遇和豐厚利潤，但電子商務不同於傳統的貿易方式，由於其的虛擬化、數字化、隱匿化等特點，對建立在傳統的生產、貿易方式基礎之上的現行稅收理論、稅收制度和稅收征管影響廣泛，涉及到增值稅、營業稅、關稅、所得稅、印花稅等多個稅種，給我國稅收提出新的而且相當嚴峻的挑戰，同時也為我國促進經濟發展，擴大稅收來源提供新的機遇。
  2. In order to describe the actual working processes of dielectric barrier discharge ( dbd ) circuit, an analysis model of differential - difference equations was presented, based on the working modes of full bridge serial load resonant dbd circuit, which was adopted with phase shifting control

    摘要為描述介質阻擋放電型臭氧發生器電路的實際工作過程，在分析一種移相全橋脈寬調制下串聯負載諧振電源供電的臭氧發生器電路的基礎上，提出了採用微分差分方程來描述電路的工作過程，並給出了電路可能的工作軌跡。
  3. In the second chapter, equivalent circuit of the eddy current sensor is firstly analyzed. based on that, the carrier signal generating circuit that is realized by the lc periodic circuit is introduced, thus, the carrier signal of standard frequency is obtained through the trimming capacity. subsequently, the disc type rotational armature generator and the rotational coupling transformer are separately leaded in to realize the power supplies of the carrier signal generating circuit and output of the measuring signal

    在傳感器設計一章中，首先對渦流傳感器進行等效電路分析，在此基礎上分析了由電感、電容諧振電路構成的載波信號發生電路，並通過微調電容獲得了標準頻率的載波信號；接下來提出了採用盤式旋轉電樞發電機解決載波信號發生電路電源供給問題的方案，同時通過旋轉耦合變壓器的引入，使得測量信號輸出問題很好地解決；本章最後給出的一組實驗曲線充分說明了這一方案的可實現性。
  4. The thesis has done the widespread investigation and study to the domestic and foreign ’ s technologies of analogy low voltage and low power, and analyzes the principles of work, merts and shortcomings of these technologies, based on the absorption of these technologies, it designs a 1. 5v low power rail - to - rail cmos operational amplifier. when designing input stage, in order to enable the input common mode voltage range to achieve rail - to - rail, it does not use the traditional differential input pair, but use the nmos tube and the pmos tube parallel supplementary differential input pair to the structure, and uses the proportional current mirror technology to realize the constant transconductance of input stage. in the middle gain stage design, the current mirror load does not use the traditional standard cascode structure, but uses the low voltage, wide - swing casecode structure which is suitable to work in low voltage. when designing output stage, in order to enhance the efficiency, it uses the push - pull common source stage amplifier as the output stage, the output voltage swing basically reached rail - to - rail. the thesis changes the design of the traditional normal source based on the operational amplifier, uses the differential amplifier with current mirror load to design a normal current source. the normal current source provides the stable bias current and the bias voltage to the operational amplifier, so the stability of operational amplifier is guaranteed. the thesis uses the miller compensate technology with a adjusting zero resistance to compensate the operational amplifier

    本論文對國內外的模擬低電壓低功耗技術做了廣泛的調查研究，分析了這些技術的工作原理和優缺點，在吸收這些技術成果基礎上設計了一個1 . 5v低功耗軌至軌cmos運算放大器。在設計輸入級時，為了使輸入共模電壓范圍達到軌至軌，不是採用傳統的差動輸入結構，而是採用了nmos管和pmos管並聯的互補差動輸入對結構，並採用成比例的電流鏡技術實現了輸入級跨導的恆定;在中間增益級設計中，電流鏡負載並不是採用傳統的標準共源共柵結構，而是採用了適合在低壓工作的低壓寬擺幅共源共柵結構;在輸出級設計時，為了提高效率，採用了推挽共源級放大器作為輸出級，輸出電壓擺幅基本上達到了軌至軌;本論文改變傳統基準源基於運放的設計，採用了帶電流鏡負載的差分放大器設計了一個基準電流源，給運放提供穩定的偏置電流和偏置電壓，保證了運放的穩定性;並採用了帶調零電阻的密勒補償技術對運放進行頻率補償。
  5. Power - supply basics

    電源供給基礎
分享友人
分享到 Line

分享到臉書