霧化顆粒尺寸 的英文怎麼說
中文拼音 [wùhuàkēlìchǐcùn]
霧化顆粒尺寸
英文
atomized particle size- 霧 : 名詞1. （水蒸氣凝結成的小水點） fog 2. （像霧的許多小水點） fine spray
- 粒 : Ⅰ名 （小圓珠形或小碎塊形物） small particles; grain; granule; pellet Ⅱ量詞（用於粒狀物）
- 尺 : 尺名詞[音樂] （中國民族音樂音階上的一級 樂譜上用做記音符號 參看「工尺」） a note of the scale in ...
- 寸 : Ⅰ量詞（長度單位） cun a unit of length （=1/3 decimetre）Ⅱ形容詞（極短或極小） very little; very ...
- 顆粒 : 1 （小而圓的東西） pellet; bead; dust; anything small and roundish （as a bean pearl etc ）2 （一...
-
The conclusions are as follows : ( 1 ) high - pressure water - atomization can be used to produce a pre - alloyed steel powder with high apparent density, high green strength, size - stability after sintering and low hydrogen - loss content ; ( 2 ) the higher smelting temperature and / or water pressure, the finer particle size of steel powders ; ( 3 ) when the atomization angle holds in a reasonable value ' s range the obtained powder will have a better particle size distribution ; ( 4 ) an optimum atomization technological parameters : liquid steel flux, water pressure and water prick angle was obtained ( 5 ) reduction variables ( temperature, holding time, material - bed ' s thickness and reducing gas flux ) have a significant effect on the particle agglomeration and properties of final powder was given ( 6 ) different alloying methods were developed to modify properties of ferrous powder materials and hence to broaden its applications in ferrous powder metallurgy industry
本文系統研究了水霧化預合金鋼粉生產工藝及合金化方法對鐵基粉末冶金材料性能影響，詳細研究了冶煉、霧化、還原工藝參數對預合金鋼粉化學成份和物理性能影響，並得出如下結論： （ 1 ）採用高壓水霧化技術可用於生產高密度、高強度、尺寸穩定性的低氫損含量的水霧化預合金鋼粉。 （ 2 ）冶煉溫度越高，高壓水壓力越大，所得生粉顆粒粒度越細。 （ 3 ）水錐角調整在一個適當角度范圍內可獲得粒度組成較好的生粉。The conclusions are drawn as following : 1. regularity of fabrication in aluminum matrix composite ring - shaped performs with large dimensions and effects of parameters were investigated, based on the novel crucible movable spray deposition technology and equipment. the optimal parameters are that the diameter of the delivery tube is 3. 8mm, spray gas pressure is 0. 8mpa, spray height is 200mm, and transferring pressure of sic is 0. 5mpa
通過系統的實驗研究得到如下結論: 1 .基於新型的移動坩堝自動化控制噴射沉積環坯制備技術及裝置，研究了大尺寸鋁基復合材料環坯的制備規律，討論了噴射沉積工藝參數對沉積坯形成過程的影響，得到了最佳工藝參數:導流管直徑d = 3 . 8mm ，霧化氣體壓力p = 0 . 8mpa ，噴射高度h = 200mm ， sic顆粒輸送壓力p送= 0 . 5mpa 。
分享友人