靜力彎曲 的英文怎麼說

中文拼音 [jìnglìwānqū]
靜力彎曲 英文
static bending
  • 靜 : Ⅰ形容詞1. （安定不動; 平靜） still; calm; motionless 2. （沒有聲響; 清靜） silent; quiet Ⅱ名詞（姓氏） a surname
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 彎 : Ⅰ形容詞（彎曲） curved; bent; crooked; flexuous; tortuous Ⅱ動詞1 （使彎曲） curved; bend; flex 2 ...
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  1. And i recommend to them that while offering up the aions justly due to him for such singular deliverances and blessings, they do also, with humble penitence for our national perverseness and disobedience, commend to his tender care all those who have become widows, orphans, mourners or sufferers in the lamentable civil strife in which we are unavoidably engaged, and fervently implore the interposition of the almighty hand to heal the wounds of the nation and to restore it as soon as may be consistent with the divine purposes to the full enjoyment of peace, harmony, tranquillity and union

    我建議在將神的供應和祝福歸於他的同時，也謙卑地悔改我們國家的彎曲悖逆，溫柔地照顧所有由於不可避免的內戰而造成的寡婦，孤兒，悼念者和痛苦的人，全力制止阻礙神的作為的企圖，讓神以全能的手治療我們國家的傷口，使其與他要我們全然享受和平，諧調，平靜與統一的神聖意旨相一致。
  2. The results indicate that if the value of press stress is over certain figure, press stress and al plate ’ s thickness have little influence on sawtooth distortion for the same kind of sawtooth ; sawtooth distortion is well - regulated under static press, while it is irregular under impact press. bottom coating make great influence on bond strength of samples which can improve the value remarkably ; bonding mechanism of clad steel is mechanism of mechanical effect that sawtooth which is hooked occludes with al plate

    結果表明：同種齒型，當壓應力大於一定的值時，壓應力和覆板的厚度對齒形的變化影響不大；靜壓下齒形變化比較規則，鋸齒頂端向一側彎曲成鉤狀；沖壓下齒形比較凌亂，鋸齒的頂端沒有明顯的變形；后處理對試樣的結合強度影響很大，打底試樣由於粘結層的作用，結合強度較高；機械作用機制是復合鋼板的主要復合機理，鋸齒彎曲成鉤狀和鋁板形成機械咬合。
  3. Glass fibre reinfroced corrugated or ribbed polyester sheets. static deflection tests under distributed load

    玻璃纖維增強聚酯波形板或加肋板.分佈荷載靜力彎曲試驗
  4. Post - tensioned pre - cast concrete simple - supported girder for railway bridge pro - stress

    預應力混凝土鐵路橋簡支梁靜載彎曲試驗方法及評定標準
  5. Since the similarity between plane elasticity and plate bending is a special case of the static - geometric analogy, this paper, therefore, studies the new formulation based on the static - geometric analogy in a broad sense

    平面彈性和板彎曲的相似性是殼體靜力?幾何比擬的特例，所以在總的意義下本文就是研究基於板殼靜力?幾何比擬理論的新型板殼單元列式。
  6. In the first place, with the similarity theory, a bridge is set up between plane elasticity and plate bending to transform those good plane elasticity elements into plate bending elements ; then with the guiding theory of the static - geometric analogy, a new methodology of thin shell element is presented

    研究的目的和解決方案首先是利用相似性理論在平面彈性有限元與板彎曲有限元之間建立一道橋梁，則可以將平面彈性中性能良好的單元轉化為板彎曲單元。之後可以在此基礎上以殼體的靜力?幾何比擬為指導理論構造新型薄殼單元。
  7. Afterward the numerical method was used to decompose the inherited integration, so the matrix form of constitution equations was derived. then through utilizing the lagrange equation directly, the paper gets the finite element formula. to test the model, the paper calculate the osteoblast ' s dynamic response under near static load and sinusoidal load at a simple tension beam and a four point bending beam

    針對單向拉伸和四點彎曲兩種離體培養成骨細胞的裝置，再根據實際情況，將培養基看成是一種多孔材料，而將成骨細胞看成是粘彈性體，利用自編的有限元分析程序分別計算了受擬靜態載荷和受交變載荷下細胞的動力響應，結果很好地反映了細胞的粘彈性性質。
  8. Cross country skis ; determination of breaking load and deflection at break with quasistatic load ; identical with iso 7797, edition 1985

    越野雪橇.準靜態載荷斷裂斷裂力和彎曲值的測定
  9. The initial strain must be the optimum value obtained by multiple - trial method. 5. in the static analysis of the bridge model under live load, assuming a shifting concentrated load on the girder, analyzing the relation map of each section deflection and the location of the concentrated load, finishing the load - on of the worst - case live load, then the moment and deflection envelope diagrams of the girder were obtained

    成橋模型建立后，在後續活載作用下的靜力分析必須首先在主樑上作用移動集中荷載，分析主梁各斷面的活載撓度與集中荷載作用位置關系曲線圖，完成最不利活載的加載，從而最後得到懸索橋主梁的彎矩包絡圖及撓度包絡圖。
  10. 3 、 based on the model, a quasi - static meshing simulation is carried out in a meshing period. the numerical results which indicating the variety of the contact status, the contact stress, the bending stress in the location of teeth root and the torque and rotary speed of gear pair vs. the different meshing position are presented, and the rationality of the model is be verified

    3 、基於所建有限元分析模型，在一個嚙合周期內，對齒輪副進行準靜態嚙合模擬分析，給出了準靜態嚙合時齒輪的接觸狀態、接觸應力、齒根彎曲應力及主從動齒輪的扭矩和轉速隨嚙合位置變化的規律，驗證了所建模型的正確性。
  11. 4 、 on the basis of analyse of a quasi - static meshing simulation in a meshing period, a dynamic meshing simulation in the case of definite torque and rotary speed are carried out in a meshing period. the numerical results which indicating the variety of the contact status, the contact stress, the bending stress in the location of teeth root and the torque and rotary speed of gear pair vs the different meshing position are presented

    4 、在對螺旋錐齒輪準靜態嚙合進行模擬分析的基礎上，進行了螺旋錐齒輪動態瞬態嚙合模擬分析，重點分析帶載啟動時出現的沖擊現象，得出了齒輪的接觸狀態、接觸應力、齒根彎曲應力及主從動齒輪的扭矩、轉速和加速度隨嚙合位置變化的規律。
分享友人
分享到 Line

分享到臉書