非規定尺寸 的英文怎麼說

中文拼音 [fēiguīdìngchǐcùn]
非規定尺寸 英文
off size
  • 非 : Ⅰ名詞1 （錯誤） mistake; wrong; errors 2 （指非洲） short for africa 3 （姓氏） a surname Ⅱ動詞1 ...
  • 規 : Ⅰ名詞1 （畫圓形的工具） instrument for drawing circles 2 （規則; 成例） rule; regulation 3 [機械...
  • 定 : Ⅰ形容詞1 （平靜; 穩定） calm; stable 2 （已經確定的; 不改變的） fixed; settled; established Ⅱ動詞...
  • 尺 : 尺名詞[音樂] （中國民族音樂音階上的一級 樂譜上用做記音符號 參看「工尺」） a note of the scale in ...
  • 寸 : Ⅰ量詞（長度單位） cun a unit of length （=1/3 decimetre）Ⅱ形容詞（極短或極小） very little; very ...
  • 規定 : stipulateprovide
  1. In order to investigate the unsteady flow frequency domain performances of an axial flow compressor at different mass flow, rotating speed and blade row spacing, plus inlet flow distortion, and considering aerodynamic characteristics and stability of the compressor, the low speed research compressor ( lsc ) at college of energy and power in nuaa is used to carry out the experiment studies. a large amount of test data has been gained through dynamic pressure transducers embedded in the stator blades at the tip, middle and hub section, then fast fourier transform algorithm ( fft ) is applied to calculate the frequency data

    為探討軸流壓氣機在工作流量、工作轉速及動?靜葉排軸向間距變化時的葉片排流場非定常頻譜特性變化規律，並耦合進氣畸變的影響，同時與壓氣機氣動性能和氣動穩定性相關聯，作者利用南京航空航天大學能源與動力學院的低速大尺寸軸流壓氣機（ lsc ）試驗器，採取在靜子葉片表面埋入動態壓力傳感器的實驗方法，對葉尖、葉中和葉根三個截面的動態壓力進行了測量，獲得了大量的可靠的實驗數據。
  2. In this paper, an optimization design cad system of detached foundation of transmitting electricity iron tower has been studied. the system uses an easy and efficient method named grid search to find out the minimum cost of an detached foundation. at the same time, the depth and width of foundation, the width of column, the thickness of foundation plan have been ascertained

    本論文研究開發的輸電鐵塔獨立基礎優化設計cad系統，以最小費用為目標，採用簡單、有效、易於編程的有約束非線性規劃方法? ?網格搜索法，對輸電鐵塔獨立基礎進行優化設計，確定出基礎埋深、基柱寬度、底板寬度、底板厚度等合理截面尺寸，並開發出計算、出圖一體化的優化設計計算機輔助設計系統。
  3. Along with silicon ulsi technology has seen an exponential improvement in virtually any figure of merit, as described by moore ’ s law ; the miniaturization of circuit elements down to the nanometer scale has resulted in structures which exhibt novel physical effects due to the emerging quantum mechanical nature of the electrons, the new devices take advantage of quantum mechanical phenomena that emerge on the nanometer scale, including the discreteness of electrons. laws of quantum mechanics and the limitations of fabrication may soon prevent further reduction in the size of today ’ s conventional field effect transistors ( fet ’ s )

    隨著超大規模集成電路的的發展，半導體硅技術非常好地遵循moore定理發展，電子器件的特徵尺寸越來越小;數字集成電路的晶元的集成度越來越高，電子器件由微米級進入納米級，量子效應對器件工作的影響變的越來越重要，尺寸小於10nm將出現一些如庫侖阻塞等新特性。量子效應將抑制傳統晶體管fet繼續按照以前的規律繼續減小。在這種情況下，宏觀的器件理論將被替代，可能需要採用新概念的晶體管結構。
  4. Figure 3 ( 2 ) the irregular - size certification marks vary in size, but must be inproportional line to the standard - size

    （二）非標準規格認證標志的規格與表一的規定不同，但必須與標準規格認證標志的尺寸成線性比例。
  5. The length should be added if the cost is n ' t increased and the installation is convenient, the diameter should be chose by the local weather condition and the using requirement ; the gas pressure should be not higher than 5 x 10 - 2pa and the emissivity should be less than 0. 1, the spring should be small and narrow in order to decrease the heat loss, the gas absorbed getter should not be too many as long as it can absorb the residual gas and keep the vacuum degree

    在不影響安裝和增加成本的情況下，應適當增加太陽能真空集熱管的長度;根據當地的氣候條件和使用要求來綜合考慮選擇直徑;國標規定的真空度必須達到5x10 』 zpa ，發射率小於0 . 1是合理的;彈簧卡子不要選用很寬、很大的尺寸，盡量減少接觸熱損;吸氣劑並非越多越好，只要能夠吸收殘余氣體，保證一定的真空度即可。
  6. In this paper, through stress analysis of region about conical and spherical parts during drawing, a calculating formula of maximum tangential compressive stess in unsupported wall region is deduced. and this is condition of causing internal wrinkle. then on the premise to guarantee not breaking workpiece, a critical calculating formula is presented

    通過圓筒形及盒形件拉深前後網格變化分析，並確定變形區和非變形區，由此得到不規則盒形件毛坯展開形狀由不變形區和參與變形拉深線組成，並用此方法計算出汽車制動閥安裝板的毛坯形狀和尺寸，在試模時一次即獲得成功，具有一定的實用價值。
分享友人
分享到 Line

分享到臉書