韌化玻璃 的英文怎麼說
中文拼音 [rènhuàbōlí]
韌化玻璃
英文
tcughened glass-
The methods - three dimension fabric - enforced laminates, and sparse fabric - enforced laminates, layer - enforced laminates ? to enhance the interlaminar toughness of fabric - reinforced laminates were discussed in this paper. the stitching method to enhance interlaminar toughness of stitched - laminates was mainly discussed in this paper based on our research and experiment. the middle - alkali glass fabric used as enforced - material with thickness of 0. 2mm, 3 section 600 deniner kevlar yarn is used as stitching thread in this research, which improved lock stitching way and different kinds of stitching mode were adopted
以提高層合板復合材料的層間斷裂韌性（能量釋放率）為目標，採用中堿玻璃布為增強材料，對疊層后的玻璃布，採用凱芙拉縫合線、改進的鎖型縫合方法、不同的縫合工藝進行了縫合；基體採用的是不飽和樹脂，固化劑為過氧化甲乙酮，促進劑為環烷酸鈷液；在室溫下採用真空輔助rtm （ resigntransfermolding ）成型固化方法，製作了不同縫合工藝的玻璃布增強復合材料層合板。They can also be used for fiber sizing, textile finishing, the reinforcing agent for cement and ceramics, and the preparation of various kinds of latex paints, and all kinds of special adhesion agents. the products of vinyl acetate - acrylic ester copolymer emulsion, which have overcome some defect of homopolymerized products, are newly developed. the modified emulsion has stronger water resistance, better flexibility, and lower glass state temperature
醋-丙共聚系列乳液產品是針對均聚產品的某些缺陷而發展起來的新膠種，它通過醋酸乙烯與丙烯酸脂類共聚改性，提高膠粘劑的耐水性和柔韌性，降低共聚物的玻璃化溫度，使產品對一些均聚乳液難以粘接的材料具有良好的粘接性能，主要產品有：寶麗板膠鋁箔紙膠塑板膠等。Specification for thermally toughened glass panels for use in domestic appliances
家用電器用熱韌化玻璃板規范Phaco emulsification cataract extraction or phaco emulsification cataract extraction combined with anterior vitrectomy as well as posterior chamber lenses implanted into the capsular bag or transsclerally sutured were performed in all cases according to the different instances of zonular fiber
治療採用晶狀體超聲乳化術，部分患者聯合前部玻璃體切除術，根據晶狀體懸韌帶鬆弛及斷裂程度實施人工晶體囊袋內植入術或人工晶體懸吊術。In this paper, the properties of fluid - modified epoxy resin containing different thinners, ethylamine anti plasticizer were tested and the effect of fluid - modified epoxy resin in repairing concrete crack through embedded pipe was compared with that of conventional grouting
測試了不同稀釋劑、固化劑及增韌劑綜合改性的環氧樹脂多組配方灌漿液的性能，對通過預埋玻璃管模擬灌漿修補混凝土裂縫的效果與通過縫面灌漿修補混凝土裂縫的效果進行了比較。The multi - purpose tester developed here is aim at testing the mechanics performance of the brittle material, which bases on modular design thought, it contains several modules as the machinery load component, platform of supporting, the function modules and the software system, they can be combined in different function modules to satisfies the need of different application situation. the tester can be used to measure not only general material properties such as elastic modulus, ultimate strain, strength, hardness and toughness, fatigue properties but also various special properties such as the local strength, and surface residual stress at the different location of the brittle component with non - destructive methods. thus the security and reliability of the brittle component can be evaluated and predicted
本文基於模塊化設計思想，研製了一臺專門針對脆性材料力學性能測試的多功能脆性材料試驗儀，其主要包括機械加載模塊、支撐平臺、功能模塊、測控系統、軟體系統等模塊，通過對這些模塊的不同組合可實現不同的功能及滿足不同應用場合要求;系統除了具有測試脆性材料的彈性模量、極限應變、強度、硬度、韌性等常規性能外，還具有無損測試玻璃構件不同位置的局部強度和表面預應力，進而對玻璃構件的安全可靠性和壽命進行預測等功能。When change the component of adhesive its shear strength increased from 39. 3 mpa to 53. 5 mpa at room temperature and it have long - term usage at 180 with 25 mpa and can be served at 230 in short period. the addition of liquid rubber resulted in a 300 % increase in the peeling strength. the addition of polymer ether imide led to a 260 % increase in the peeling strength, a 15 % increase in shear strength and a 10 increase in tg ( tg = 195. 54 )
研究結果表明： bmi dds e ? 51 tde ? 85組成的膠粘劑體系的室溫剪切強度為39 . 3mpa ，當改變環氧樹脂的含量時，剪切強度提高到53 . 5mpa ；用無規羧基液體丁腈橡膠改性環氧樹脂膠粘劑時室溫剝離強度提高3 . 0倍；用聚醚酰亞胺改性環氧樹脂膠粘劑，室溫剪切強度最高可達45 . 2mpa ，剝離強度提高2 . 6倍，玻璃化轉變溫度tg = 195 . 54 ，比未增韌體系提高10以上；碳纖維耐磨材料與同步器圓錐環的粘接實驗結果表明，膠粘劑的使用工藝性能良好，滿足室溫剪切強度30mpa和180剪切強度12 . 5mpa的技術要求。分享友人