預熱層 的英文怎麼說

中文拼音 [yùrècéng]
預熱層 英文
preliminary heating zone
  • 預 : Ⅰ副詞（預先; 事先） in advance; beforehand Ⅱ動詞（參與） take part in
  • 層 : i 量詞1 （用於重疊、積累的東西 如樓層、階層、地層） storey; tier; stratum 2 （用於可以分項分步的...
  1. The welding performance of homemade wear - resistant cast steel has been studied base on the weldability tests, the repair welding procedures of wean - resistant cast steel ( abrasion - plates ) have been made up, the results show that satisfying repair welding quality can be attained with such welding conditions as the low hydrogenous alkalescent welding rod, preheating and slow cooling, strictly maintaining the interbedded temperature of 250 ~ 300 and controlling welding technique

    通過對其焊接性能的試驗研究，制定了該類鑄鋼件（磨耗板）的補焊工藝：低氫型堿性焊條，預熱與緩冷相結合的工藝措施，嚴格控制層間溫度（ 250 ~ 300 ）及焊接工藝規范，可獲得滿意的修復質量。
  2. 2. dynamic meteorology : equations of motion ; geostrophic, ageostrophic and gradient winds ; thickness and thermal wind ; continuity equation ; stream function ; vorticity equation ; divergence equation ; omega equation ; rossby wave ; ekman layer ; numerical weather prediction

    2 .動力氣象學：運動方程地轉風非地轉風及梯度風厚度及熱成風連續方程流函數渦度方程輻散方程奧米茄方程羅斯貝波埃克曼層數值天氣預報。
  3. In this paper, thermal evolution history of organic matter of the source rocks and hydrocarbon generation history have been researched by tti method, hydrocarbon migration direction and migration times were probed combining with the area structure development feature ; distribution pattern of the main reservoir intervals on lateral and longitudinal have been predicted by researching on development feature and control factors of the reservoir intervals, the actions of reservoir conditions in hydrocarbon accumulation and bearing also were probed combining with pore evolution feature ; the micro - pore feature of regional cap and direct seal in carboniferous - lower triassic in this area have been determined with micro - capillary pressure curve and intrusive mercury curve ; the prospecting districts have been pointed out combining with the hydro - geologic feature, the potential reservoirs were classified according to trap types in this area, the author attempt to evaluate on the hydrocarbon - bearing condition in the str ata of carboniferous ~ lower triassic from hydrocarbon generation and migration reservoir condition, reserved condition etc, and predict the reservoir types and hydrocarbon - bearing patterns combining with the structure evolution. based on above, the author point out that the central block of chenghu - tuditang synclinorium and the southern block of dangyang synclinorium are the advantageous regions for exploration

    本文用tti方法研究了烴源巖有機質的熱演化史和油氣生成史，並結合區內構造發育特徵，探討油氣在區域上的運移方向和在時間上的運移期次；通過對儲集層段的發育特徵和控制因素的研究，預測了本區主要的儲集層段在橫向上和縱向上的分佈規律，並結合孔隙演化特徵，探討儲集條件在油氣聚集成藏中的作用；利用微毛細管壓力曲線法和壓汞法，對石炭系?下三疊統的區域蓋層和直接蓋層的微孔隙特徵進行了定量評價，並結合水文地質分佈特徵，指出有利於油氣保存的地區；根據區內存在的各種圈閉類型，對可能存在的油氣藏進行了分類，並試圖從油氣的生成與運移、儲集條件、保存條件等方面，動態地綜合評價石炭系?下三疊統油氣成藏條件，並結合構造演化特徵，預測其油氣藏類型和成藏模式。
  4. The limited hydrothermal karst and mixed zone beneath the anticline axis controls the porosity distribution of ordovician system and it is anticipated that surroundings of the axis of fold formed by compressional reverse orverthrusting during indo - chinese epoch and the coordinated area of morphology of anticline in the screen of buried hill and that of top surface morphology is the best position for development of the reservoir

    局限的熱液巖溶和裸露的背斜軸部之下的混合帶對千米橋潛山奧陶系孔隙分佈具有重要控製作用，預期在印支期擠壓逆沖作用形成的背斜軸部，特別是潛山內幕背斜形態與潛山頂面形態相互協調的區域，應是儲層發育最好的部位。
  5. Finally, it also discusses the sign ifi cance of thermal fluid flow to pool - forming dynamics ： ( 1 ) provides a new ex planation way to abnormal vitrinite reflectance, which can enlarge the fields of hydrocarbon exploration and development ; ( 2 ) provides some important evidences to research of hydrocarbon migration, which support to choose exploration targ e ts ; and ( 3 ) provides means to study diagnesis and porosity evolution of reservo ir rocks, which can be used to predict the development units of deep reservoir s

    最後，探討了熱流體活動對成藏動力學研究的重要意義，認為其可為有機質演化異常提供新的成因解釋途徑，擴大油氣勘探領域；為油氣運移的研究提供線索，優化勘探目標選擇；為成巖-孔隙演化的動態研究提供依據，預測深部儲層發育層段。
  6. Through summarization for complicated geohydrology and engineering geology condition of research area, the non - stability 3 - dimension flow model of ground water and land subsidence model were established in this thesis. the coupled models of ground water and land subsidence were combined with a large series of water level observation and land subsidence information to debug the parameters and ascertain the models

    兩者通過含水層的水位內在聯系耦合在一起，並根據研究區水文地質條件及抽水試驗資料，結合大量的水位觀測序列資料及地面沉降觀測資料對模型進行調參，標定地下熱水運移的三維有限元數值模型，所建模型可以對地下水水位及地面沉降同時進行模擬預測。
  7. The nature conservancy of cement tile blank. after the surface coating production line in preheated purge bottom spray drying intermediate layer spray drying launched drying table a total of three cooling heating and drying surface, the second spraying process, weatherability cement tiles surface coating to achieve the best performance

    自然養護后的水泥瓦坯，在塗裝生產線上經過表面吹掃預熱乾燥底層噴塗中間乾燥面層噴塗面塗乾燥表面冷卻共三次加熱乾燥二次噴塗的工藝過程，使水泥彩瓦表面耐候性塗層達到最佳性能。
  8. The analysis of the large - scale synoptic situation shows that strong precipitation is closely related to the explosion of monsoon and the intensification of cross - equatorial flow which bring a lot of vapor and meet with cold masses at the eastern of northwest district on 8th, june causing extremely heavy rainfall ; that subtropical high - level jet at 200hpa, subtropical high at 500hpa and low - level jet at 850hpa are the weather backgrounds favorable to strong precipitation ; that the pattern of eastern highs and western lows and the establishment of a low - level jet and the coupling between upper - and low - level patterns that determine that the rain occurred in the east of the northwest china ( on average, this is the rainy season for the south of china, but not for the northwest china ) ; that water vapor comes from southerly and easterly flow which converge at the eastern of northwest district with convergence mainly in lower levels and pbl ; that the high value of the whole - level apparent heat source < q1 > is near the area of large rainfall in the direction of northeasterly - southwesterly agreeable to shear line very well and the condensation latent heat releasing is main heat source with vertical advection item playing key role in q1 and q2 ; that there is a vertical secondary circulation crossing low - lever jet whose ascending branch is at the area of large rainfall ; that the construction of convection instability and conditional symmetry instability results that there is not only deep thermal instability, but also moisture influx and triggering mechanism of thermal instability causing strong torrential rain

    作為對比，本文還對2002年6月24 - 25日發生在北京地區的強地形雨進行了分析，並討論陜南、北京地區兩地暴雨的異同點以及地形作用的共性和個性，為兩地暴雨預報提供有益的參考，得出了一些很有意義的結果： 1大尺度環流背景分析表明： （ 1 ） 「 02 . 6 」強降水與6月上旬越赤道氣流和季風爆發密切相關，攜帶大量水汽的偏南氣流與冷空氣於6月8日交匯在西北地區東部，導致了這次強降水的發生； （ 2 ） 200hpa的副熱帶西風急流、 500hpa副高以及850hpa的低空急流的配置非常有利於本文分析之陜西強降水的發展與維持。大尺度形勢分析表明，東高西低形勢場、低空急流的建立和高低空形勢的配置決定了這場降雨出現在西北地區東部。與暴雨區相聯系，存在一支橫越低空急流的經向垂直環流，暴雨區處于該垂直環流的上升支； （ 3 ）偏南和偏東氣流水汽通道在西北地區東部交匯，水汽的輻合積聚主要在對流層低層和行星邊界層內完成； （ 4 ）整層的視熱源< q _ 1 >高值區在暴雨區附近呈東北-西南向分佈，與切變線走向非常一致，降水產生的凝結潛熱釋放是強降水區大氣的主要熱源。
  9. Wear resistant layer of cylinder and double - layer liner in catalyst creaking apparatus ( without or with tortoiseshell net can be used ), inner liner of carbon monoxide exhaust - heat boiler, pouring at site for furnace roof with high temperature of heating furnace of steel rolling, different forging furnace, resistance furnace, the prefabricated parts can also be made

    催化裂化裝置中的筒體耐磨層及雙層襯里， （無龜甲網和有龜甲網均可採用）及一氧化碳余熱鍋爐的內襯，也適用於軋鋼加熱爐、各種煅造爐、電阻爐的爐頂、爐墻、爐底高溫部位的現場澆注，可製成預制構件。
  10. District heating pipes - preinsulated bonded pipe systems for directly buried hot water networks - pipe assembly of steel service pipe, polyurethane thermal insulation and outer casing of polyethylene

    區域供暖管道.直埋式熱水供暖網的預絕熱連接的管道系統.聚氨酯絕熱層和聚乙烯外覆層的鋼管組件
  11. The group expects the 5 - stand cold mill to be erected in first half of 2006 while the hot mill will be completed by the end of 2006

    管理層預期五連軋冷軋機將可於二零零六年上半年落成，熱軋機則預計於二零零六底竣工。
  12. Numerical prediction to heat - treatment - induced surface deformation of titanium alloy thin wall workpiece coated with nitride layer

    含氮表層對鈦合金薄壁件熱處理變形影響的數值預報
  13. Design and installation of preinsulated bonded pipe systems for direct heating

    直接採暖用的粘結預隔熱層管道系統的設計和安裝
  14. Welding. guidance on the measurement of preheating temperature, interpass temperature and preheat maintenance temperature

    焊接.預熱溫度層間溫度和預加熱的維持溫度的測量導則
  15. Welding - guidance on the measurement of preheating temperature, interpass temperature and preheat maintenance temperature iso 13916 : 1996 ; german version en iso 13916 : 1996

    焊接.預熱溫度層間溫度和預加熱維持溫度測量導則
  16. 5. in response to heat conduction test, air heat - insulation course is proved to work well, it reduces temperature difference of tank walls greatly and prevents cracks effectively

    進行了罐體熱傳導試驗，證明了空氣隔熱層具有令人滿意的效果，大大降低了罐壁溫差，有效預防了溫度裂縫的發生。
  17. Bake in a preheated 190c / 375f oven for about 30 minutes. take out the muffins and brush the tops with a thin layer of oil. continue baking for another 10 minutes

    入預熱190c / 375烤箱烘焙30分鐘左右，打開烤箱，在表面上刷上一層葵花籽油，繼續烘焙10分鐘即可。
  18. Preheat oven to 170 c. combine all ingredients together and set aside overnight. spread a very thin layer on a silicone baking mat

    烤箱預熱至170 。混合以上所有材料並放置一晚后將材料薄薄的一層鋪再烤盤紙上入烤箱烘培。
  19. Lightly grease the muffin tin or line with paper cups. place all - purpose flour, corn flour, salt and baking powder in a bowl. preheat the oven to 190c / 375f

    麥芬盤抹上一層薄油或是鋪上麥芬紙杯。把中粉，玉米粉，鹽和烤粉混合備用。烤箱預熱到190c / 375f 。
  20. Preheat oven to 180c / 350f. brush the loaf with the egg wash again and sprinkle the top with oatmeal bran. place it into the oven, bake about 35 minutes

    烤箱預熱至180c / 350f 。發好的麵包再刷上一層蛋白液，灑上燕麥麩后入烤箱烘焙35分鐘左右。
分享友人
分享到 Line

分享到臉書