預熱燃燒器 的英文怎麼說

中文拼音 [yùrèránshāoqì]
預熱燃燒器 英文
preheat burner
  • 預 : Ⅰ副詞（預先; 事先） in advance; beforehand Ⅱ動詞（參與） take part in
  • 燃 : 動詞1. （燃燒） burn 2. （引火點著） ignite; light
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 燃燒 : （物質劇烈氧化而發光、發熱; 燒） burn; kindle; flame; set on fire; [化學] combustion; inflammation; ignition
  1. The top - firing air and gas self - preheating hot blast stove adopts a patented burner and high blast temperature bypass flue

    摘要頂燃式空氣、煤氣自身雙預熱熱風爐採用了頂燃式燃燒器熱風爐專利的燃燒器技術和高溫旁通煙道技術。
  2. From simulations and data of fire site, most air preheater fire often appear when boiler is started in cool state and standby which fuels of insufficient combustion coagulate and congregate on the parts of air preheater. when the temperature of smoke inpouring air preheater increases, aggregate fuels and sediments will combust in stated temperature conditions. it is called the second combustion of air preheater

    這些起火起因於燃料油的不充分燃燒，其結果是未充分燃燒的燃料油凝結和聚集在空氣預熱器的部件上，當進入空氣預器的煙氣溫度增高時，沉積的燃料油被烘烤，當達到一定溫度條件時，則可點燃這些燃料油污沉積物，造成火災發生，這通常被稱為空氣預熱器的二次燃燒。
  3. Abstract : the in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging

    文摘:針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況，提出了若干技術改造措施包括，增大對流管表面積以增大對流段的熱負荷；增加輻射管的換熱面積；修正煙囪高度；換用新型燃燒器，變自然通風為強制供風，以增大燃燒器的發熱量，減小過剩空氣系數，節省燃料2 % 3 % ；在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度；採用高溫輻射塗料增強輻射換熱效果，從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。
  4. The in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging

    針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況，提出了若干技術改造措施包括，增大對流管表面積以增大對流段的熱負荷；增加輻射管的換熱面積；修正煙囪高度；換用新型燃燒器，變自然通風為強制供風，以增大燃燒器的發熱量，減小過剩空氣系數，節省燃料2 % 3 % ；在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度；採用高溫輻射塗料增強輻射換熱效果，從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。
  5. With the rapid development of computational fluid dynamics and combustion theory, applying the computer to numerically simulate the complicated processes in the plasma ignition is possible. using numerical simulation can estimate the parameters which are not essay to measure and not doing so many experiments can improve its reliability and reduce the cost. so numerical simulation is a new pattern way to study the inner mechanism of the plasma ignition

    隨著計算流體力學和燃燒理論的發展及計算機的廣泛應用，用數值模擬等離子點火器內部燃燒系統流動、傳熱、傳質、化學反應等復雜的過程已成為可能。應用數值模擬的方法可以對實驗難以測量的量進行預估，而不需要大量的試驗，應用數值模擬的方法來解決等離子點火器燃燒性能的分析和工程設計，有利於提高工作的可靠性和經濟性。
  6. In this article, constituting some the equations which reflect the flow law and building and applying many mathematical models of physical and chemical reactions in the the plasma ignition : applying k - two equations turbulence model to calculate the turbulence parameter supplying simplied reaction systerm model and applying eddy break - up model and p - i thermal radiation model. with these reasonable simplied modles, numerically simulating the flow field in the plasma ignition. during the numerical simulation, applying the body - fitted coordinates for the complex geometry of the computional field ; using the mixing format to disperse the equations ; applying simplec algorithm method to solve the equations ; using above models and methods, it can get flow field distribution ; including temperature, pressure, turbulent kinetic energy and its dissipation rate, turbulent viscosity, velocity, density. these results are significant to design and improve the plasma ignition

    本文旨在通過構造反映等離子點火器內部流動規律的基本方程組，建立描述等離子點火器內部的復雜物理化學過程機制數學模型：模擬等離子發生器內部燃燒的-雙方程湍流流動模型；模擬氣體燃料在燃燒時中化學反應的簡單化學反應系統模型；模擬等離子點火器內部湍流預混燃燒的漩渦破碎模型；模擬等離子點火器高溫燃氣及其壁面的p - i輻射換熱的模型等等，對模型進行一定的合理的簡化，然後數值模擬等離子點火器內部流場的流動。
  7. Prevention and disposal of rotary air pre - heater secondary combustion

    回轉式空氣預熱器二次燃燒的預防與處理
  8. Ensures cleaner tanks, lines, strainers, preheaters and burners

    清潔油罐（箱） 、管路、過濾器、預熱器以及燃燒器。
分享友人
分享到 Line

分享到臉書