預熱薄膜 的英文怎麼說
中文拼音 [yùrèbómó]
預熱薄膜
英文
preheated film-
It is composed of evaporator, vapor separator, preheater and a simple separator. the evaporator is climbing film
本薄膜蒸發器機組由蒸發器汽液分離器預熱器三個部件和一隻簡易分離器組成，蒸發器為升膜式列管換熱器。Prepainted hot - dip zinc - coated steel sheets and coils
預塗膜熱浸鍍鋅薄鋼板和卷材( 3 ) according to the study of heat treatment process, heat treatment ambience, airflow and heat treatment temperature were considerd as the important influences on the quality and property of ybco films. through optimizing the process, the ybco films were prepared on sto single crystal, and their room temperature resistance was about 200 ybco films also were fabricated on the sto buffered si substrate, and their room temperature resistance was about 300d
（ 3 ）根據本文熱處理過程的工藝探索，認為熱處理氣氛、氣流量及處理溫度是影響薄膜質量及性能的重要因素，通過優化工藝過程，在鈦酸鍶（ sto ）單晶上制得的ybco薄膜表面質量良好，室溫電阻200左右；而在預制了鈦酸鍶（ sto ）緩沖層的si基板上制備的ybco薄膜的室溫電阻為300左右。5 ) as the deformation strain increases the reverse transformation temperature and thermal hystersis of tini film increase on the first heating, while the martensitic transformation temperature decreases and r phase transition temperature is constant
隨預應變量增大， tint薄膜的第一次逆相變溫度升高，相變熱滯增大，馬氏體相變溫度降低， r相變溫度無明顯變化。Using the microwave selective heating property for materials, by setup equivalent equation, and first time inducing the electromagnetic field perturbation theory to the design of heating materials for substrate in mpcvd, three temperature distribution modes were established, including temperature distribution comprehensive mode of inhomogeneous plasma, temperature distribution composite mode of composite substrate materials, temperature distribution perturbation mode of composite materials, which ii provided an whole new technology route to the design of substrate heating system in mpcvd and guided the preparation of heating materials for substrate. and then the heating materials for substrate were designed and optimized to obtain large area homogeneous temperature distribution even larger than substrate holder ' s diameter. as an important part, this thesis researched the nucleation and growth of diamond films in mpcvd, systematically researched the effects of substrate pretreatment, methane concentration, deposition pressure and substrate temperature etc experimental technologic parameters on diamond films " quality on ( 100 ) single crystal silicon substrate in the process of mpcvd, characterized the films qualities in laser raman spectra ( raman ), x - ray diffraction ( xrd ), scanning electron microscopy ( sem ), infrared transmission spectra ( ir ), atomic force microscopy ( afm ), determined the optimum parameters for mpcvd high quality diamond in the mpcvd - 4 mode system
該系統可通過沉積參數的精確控制，以控制沉積過程，減少金剛石膜生長過程中的缺陷，並採用光纖光譜儀檢測分析等離子體的可見光光譜以監測微波等離體化學氣相沉積過程；利用微波對材料的選擇加熱特性，通過構造等效方程，並首次將電磁場攝動理論引入到mpcvd的基片加熱材料的設計中，建立了非均勻等離子體溫度場綜合模型、復合介質基片材料的復合溫度場模型及復合介質材料溫度場攝動模型，為mpcvd的基片加熱系統設計提供了一條全新的技術路線以指導基片加熱材料的制備，並對基片加熱材料進行了設計和優選，以獲取大面積均勻的溫度場區，甚至獲得大於基片臺尺寸的均勻溫度區；作為研究重點之一，開展了微波等離體化學氣相沉積金剛石的成核與生長研究，系統地研究了在（ 100 ）單晶硅基片上mpcvd沉積金剛石膜的實驗過程中，基片預處理、甲烷濃度、沉積氣壓、基體溫度等不同實驗工藝參數對金剛石薄膜質量的影響，分別用raman光譜、 x射線衍射（ xrd ） 、掃描電鏡（ sem ） 、紅外透射光譜（ ir ） 、原子力顯微鏡（ afm ）對薄膜進行了表徵，確立了該系統上mpcvd金剛石膜的最佳的實驗工藝參數。Since the phase transformation behavior of tini thin film has a great influence on the properties of micro - actuator, both ti - rich and ni - rich tini thin films " phase transformation behavior were studied in this stud ) "
本文從微驅動材料tini薄膜的相變行為對微驅動器性能影響出發，採用電阻法、 dsc 、 xrd 、 tem等手段，研究了tini非晶薄膜晶化過程、熱處理、熱循環以及預變形等對tini薄膜相變行為的影響。The surface of the films was observed for the films heated with many times by laser beam, it was found that pzt films " interfacial crack appeared
重復多次激光作用后，觀察其形貌，發現薄膜出現界面裂紋，這與鄭學軍用激光熱疲勞模型預測的結果一致。The warm - up device can reduce the temperature difference between the cloth and the molten film, so it improve the intensity of antis tripping, reduce the gaffer of the film
預熱裝置縮小了材料和熔融薄膜的溫度差，保證了塗覆后抗剝離強度高，減輕塗覆后的皺褶。Prepainted hot - dip zinc - 5 % aluminium alloy - coated steel sheets and coils
預塗膜熱浸鍍鋅. 5 %鋁合金鍍層薄鋼板和卷材分享友人