預軟化劑 的英文怎麼說
中文拼音 [yùruǎnhuàjì]
預軟化劑
英文
pre softener- 預 : Ⅰ副詞（預先; 事先） in advance; beforehand Ⅱ動詞（參與） take part in
- 軟 : Ⅰ形容詞1 （質地不硬） soft; flexible; supple; pliable 2 （柔和） soft; mild; gentle 3 （軟弱） we...
- 劑 : Ⅰ名詞1 （藥劑; 制劑） a pharmaceutical or other chemical preparation 2 （某些有化學作用的物品） a...
- 軟化 : 1 （由硬變軟） soften; [皮革] bate; bating 2 （由堅定變為動搖） win over by soft tactics 3 （由倔...
-
In this paper, a high performance sma system applied to steel bridge deck is put forth in allusion to the pavement project of the wuhan junshan yangtze river highway bridge. it comprises steel slab, zn coating layer, closing layer, adhesive, pre - mixed asphalt stone and dual layer sma from bottom to top. it is based on the fea results of the forces and deformation of the pavement layer by means of the algor feas, according to this bridge ' s traffic and the ambient temperature varying range of the pavement layer
本文針對武漢軍山長江公路大橋鋼箱梁橋面鋪裝工程，從鋪裝層環境溫度變化范圍、交通量等使用條件出發，在用algorfeas有限元分析軟體分析鋪裝層受力變形基礎上，提出了（即鋼板+金屬鋅塗層+封閉層+粘接劑+預拌瀝青碎石+雙層sma ）的高性能鋼橋面sma鋪裝體系，並對這種sma的組成材料，包括改性瀝青、集料、礦粉、纖維進行了比較研究，設計了這種sma的配合比，對sma混合料的性能進行了對比試驗，對這種sma方案進行了疲勞性能研究，驗證了所選擇sma方案的可行性。In my paper i used the " triangle " method, which is brought forward by glajch, to design 5 turn experiments, then optimizing. i have also developed the procedure with tool of vb and flash, realized the automotive optimization of simplex
本文以glajcn 『 』三角形法為基礎，設計5次預試驗，採用可變「步長」的單純形法，用vb語享和fiash動畫製作工具，進行軟體開發，實現了使用單純形治優化hplc溶劑系統的自動化。Performance for a piezoresistive transducer pressure sensor to thermal and pressure environments can be predicted by finite element method. a simplified 1 / 8 model, considering silicon dioxide and nitride process as well as stack anodic bonding and adhesive bonding processes, was developed. the fem results were found to be comparable to experimental data. case studies suggested that pyrex stack induces certain amount of non - linearity, while it isolates hard epoxy nonlinear effect. flexible epoxy bonding or soft adhesive bonding is preferred to the packaging process. the viscoelasticity and viscoplasticity of bonding material will result in hysteresis and drift errors to sensor output. however, soft adhesive s influence on sensor can be ignored under relative stable environments. more over, detailed design and process information will help to improve modeling application
熱、壓環境下壓阻變換壓力傳感器的性能可以通過有限元方法預測.這里研究了簡化的1 / 8模型，模型考慮了二氧化硅和氮化硅生成過程及堆陽極鍵合和膠粘結合過程.結果發現有限元預測結果和實驗數據具有可比性.範例研究表明，硼硅堆導致產生一定的非線性，但它隔離了硬環氧樹脂的非線性.在包裝過程中最好使用柔性環氧黏合或軟黏膠性結合.黏合材料的黏彈性和黏塑性將會導致傳感器輸出的滯后和漂移誤差.然而，在相對穩定的環境下，軟黏合劑對傳感器的影響可以忽略.此外，詳細的設計和過程信息有助於提高模型的適用性
分享友人