額定水頭 的英文怎麼說

中文拼音 [édìngshuǐtóu]
額定水頭 英文
normal head
  • 額 : 名詞1 （額頭） forehead:寬額 a broad forehead2 （牌匾） a horizontal tablet 3 （規定的數目） a sp...
  • 定 : Ⅰ形容詞1 （平靜; 穩定） calm; stable 2 （已經確定的; 不改變的） fixed; settled; established Ⅱ動詞...
  • 水 : 名詞1 （由兩個氫原子和一個氧原子結合而成的液體） water 2 （河流） river 3 （指江、河、湖、海、洋...
  • 水頭 : waterhead; head; flood peak水頭落差 head fall; 水頭坡降 water table gradient
  1. Do processing of preliminary emergency treatment to want to notice : eye ministry is bumped by stupid thing, local generation strut reachs ache, without the cut that the skin opens, can use cold towel cold compress, reach with subsidence of a swelling reduce ache ; if eye ministry is traumatic, bleed, the gauze of usable cleanness wraps up ; if the eyewinker flies inside pleasant to see, must not rub rubs an eye, should close double key point gently or blink a bit, let express light foreign body to be poured out of along with tear ; if the eyewinker has entered eyeball deep, eyeball already break - through, cannot oppress absolutely right now eyeball, lest emergence is organized inside the eye ; if forehead and eyebrow bend ministry are contused to want to note the eyesight case of seasonable self - check eye, preliminary judgement has injure secondhand without optic nerve

    做初步急救處理要注重：眼部被鈍物撞擊，局部產生腫脹及疼痛，無皮膚開放的傷口，可用冷毛巾冷敷，以消腫及減輕疼痛；若眼部外傷引起眼瞼裂傷或出血，可用清潔的紗布包紮；若有異物飛入眼內，千萬不要搓揉眼睛，要輕閉雙眼或稍眨眼，讓表淺的異物隨淚水流出；假如異物已經進入眼球深部，眼球已經穿通，此時絕不可壓迫眼球，以免眼內組織脫出；若額頭和眉弓部被撞傷要注重及時自我檢查眼睛的視力情況，初步判定有無視神經間接損傷。
  2. The open angle, head loss and hydrodynamic pressure under the rated flow and several kinds of proportion are carefully observed in the model test, and these results are given for reference in engineering design

    階段模型試驗中詳細觀測了在額定流量下，不同比重拍門的開啟角度，水頭損失及門體動水壓力變化情況，以供工程設計應用參考。
  3. After each day ' s settlement, if the balance of his margin account is above the " maintenance margin " level, mr tan will not get a " margin call "

    每天結算、把損益過帳到保證金戶頭后，只要保證金余額高於規定的「維持保證金」水平，盤口持有人就不會收到「補倉通知」 。
  4. From the management mode and integrating the aircraft part production characteristics, analysis and studies the integrated management of the manufacturing information, the organizing of the production plan and the control of the production process of the part manufacturing workshops which is under the cims environment, integrate with lean production idea. and this paper also applies concrete system analysis, promote general design plan and model establishing method. this thesis mainly discusses the workshop production practical flow, brings forward the new " month, week, day three class plan control " method, expects to apply effective control to the overall production process

    本論文在了解了同行業企業的製造管理模式之後，以西安飛機工業（集團）有限責任公司零件製造車間為例，對零件製造車間進行系統的研究和分析，在此基礎上開發一個基於cims環境下適合零件製造車間的生產作業計劃管理系統，與精益生產方式（ leanproduction ） 、精益思想相結合，並對其管理系統進行研究，達成以生產計劃、生產調度為龍頭，充分利用工藝、工裝、工時定額等製造信息，科學編制生產的月、周、日計劃，高效的支配生產資源（如人、設備、工具、輔助材料等等） ，動態組織生產調度，準確預測隱患，全面監控生產過程，從而達到有效的提高生產效率的目的，並利用科學的管理方式最終提高我們的製造水平。
分享友人
分享到 Line

分享到臉書