飛行配平 的英文怎麼說

中文拼音 [fēihángpèipíng]
飛行配平 英文
flight trim
  • 飛 : Ⅰ動詞1 （鳥、蟲等在空中活動） fly; flit 2 （利用動力機械在空中行動） fly 3 （在空中飄浮遊動） fly...
  • 行 : 行Ⅰ名詞1 （行列） line; row 2 （排行） seniority among brothers and sisters:你行幾? 我行三。where...
  • 配 : Ⅰ動詞1 （兩性結合） join in marriage 2 （使動物交配） mate （animals） 3 （按適當的標準或比例加以...
  • 平 : Ⅰ形容詞1 （沒有高低凹凸 不頃斜） flat; level; even; smooth 2 （高度相同; 不相上下） on the same l...
  • 飛行 : flight; flying; aviate; voyage; volitate; hop
  1. Aerodynamic prediction and analysis for a reentry vehicle with slice - ailerons

    配平翼飛行器的氣動計算及分析
  2. The system hardwire includes : flexible vehicle management system architectures, fiber optic cable plants, active hand controllers, primary flight control computers, optical mechanizations and smart actuators

    同時還介紹了一單通道主飛控系統的地面演示和一副翼配平控制系統的飛行演示。
  3. The aircraft ' s longitudinal motion short period poles and long period zeros in right plan e may make the aircraft control system be not got by only using qft. so pole and zero assignment by state feedback is needed to change this circumstances and then qft is used to get the control system. simulink results are given to prove at the system meets the requirements.

    飛機縱向運動方程的短周期和長周期的右半平面可能存在零極點對問題，這對飛機控製造成不利影響，直接利用定量反饋理論不能滿足要求。本次論文首先進行短周期狀態反饋極點配置，然後利用定量反饋來解決這個問題。通過模擬分析得到滿意的結果。
  4. The design of configuration and other primary structures of the helicopter have been finished. in order to analysis the stability and control of the helicopter, a flight mechanical modeling has been founded based on a single - rotor helicopter

    本文以常規單旋翼帶尾槳的直升機配平和操穩計算方法為基礎，建立了帶涵道共軸式直升機飛行動力學模型，對碟形無人直升機進行了配平和操縱性和穩定性分析計算。
  5. A new distributed compute technique - corba object service, in which event service and naming service are the basic object service, can be used to accomplish a flexible configuration and integration of modules existed in the network architecture, and can provide an open platform for uah flight control components integrating. consequently uah would own the ability to on - line reconfigure and adapt to environmental change

    利用corba對象服務? ?事件服務和命名服務是其中兩個基本的對象服務? ?可實現運行在網路體系中組件的靈活配置和集成，為uah分散式飛行控制系統的集成提供開放式平臺，從而實現了uah的在線重配和自適應能力。
  6. In the present dissertation, the densification mechanisms and the structure controlling of various transient layers of w - mo - ti flier - plates with graded wave impedance were mainly investigated. wholly dense w - mo - ti flier - plates were then prepared by powder stacking and hot - pressing. in order to achieve a required wave impedance profile and a quasi - continuous change along the thickness direction, the ratios of components in transient layers were well adjusted

    論文採用粉末冶金方法，詳細研究了w - mo - ti體系梯度飛片材料中各組元的燒結緻密化機理與控制方法，以精細控制不同配比的混合粉末的鋪填方式與鋪填結構來減小梯度飛片材料內部波阻抗值的躍變幅度，成功制備出波阻抗按指定分佈特徵沿厚度方向準連續變化的、波阻抗面平行度高並且整體緻密的w - mo - ti體系梯度飛片。
  7. Meanwhile, objective to the requirement of both real - time and accuracy for moving shaped target detect and tracking, a novel method is proposed based on combination of images difference and feature invariant. the paper improved the tradition difference method, constituted a feature invariant which characterized the object contour without influence of object ’ s size change, shifting, and rotation, and developed a dynamic - extremum - matching scheme

    同時，針對識別跟蹤具有形狀信息的大飛行器目標所提出的快速準確要求，提出了一種基於改進的差分演算法與特徵不變量匹配的目標識別方法，彌補了傳統圖像差分方法的不足，構造了一個具有平移、大小和旋轉不變性的特徵不變量用於識別目標，並研究出一種動態極值匹配方案。
  8. From the management mode and integrating the aircraft part production characteristics, analysis and studies the integrated management of the manufacturing information, the organizing of the production plan and the control of the production process of the part manufacturing workshops which is under the cims environment, integrate with lean production idea. and this paper also applies concrete system analysis, promote general design plan and model establishing method. this thesis mainly discusses the workshop production practical flow, brings forward the new " month, week, day three class plan control " method, expects to apply effective control to the overall production process

    本論文在了解了同行業企業的製造管理模式之後，以西安飛機工業（集團）有限責任公司零件製造車間為例，對零件製造車間進行系統的研究和分析，在此基礎上開發一個基於cims環境下適合零件製造車間的生產作業計劃管理系統，與精益生產方式（ leanproduction ） 、精益思想相結合，並對其管理系統進行研究，達成以生產計劃、生產調度為龍頭，充分利用工藝、工裝、工時定額等製造信息，科學編制生產的月、周、日計劃，高效的支配生產資源（如人、設備、工具、輔助材料等等） ，動態組織生產調度，準確預測隱患，全面監控生產過程，從而達到有效的提高生產效率的目的，並利用科學的管理方式最終提高我們的製造水平。
分享友人
分享到 Line

分享到臉書