高原變壓器 的英文怎麼說

中文拼音 [gāoyuánbiànyāqì]
高原變壓器 英文
high-altitude transformer
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 原 : Ⅰ形容詞1 （最初的; 原來的） primary; original; former 2 （沒有加工的） unprocessed; raw Ⅱ動詞（原...
  • 壓 : 壓構詞成分。
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 高原 : [地理學] continental plateau; plateau; highland; tableland
  1. The second, at the high frequency primary coil, when switch turn on with control signal ( the spwm pulse is modulated ), in the positive or negative semi - period of low frequency modulation signal, transformer coil with same direction voltage. the magnetic flux of transformer core will increase step by step. at the end, it leads to magnetic flux saturation

    二、在高頻變壓器原邊，當開關管接收控制信號脈沖列（經調制的spwm波列）導通時，在低頻調制信號的正半周或負半周內，施加在變壓器繞組上的是同一方向的電壓，變壓器磁芯中的磁通可能將級進地逐漸增加，導致磁芯飽和，造成磁偏或單向磁化，導致低頻電信號放大失真或由於很大的磁化電流而無法正常工作。
  2. This text draws the basic principle of infrared diagnoses based on the primary knowledge of infrared radiation, and analyse the imaging principle of infrared devices ; from the view of infrared diagnostic technology we discuss the fault models and the principium of infrared diagnosis on electrical equipments ; then this paper research the diagnosis of electrical equipments fault by using infrared devices, obtain the hot picture atlas of equipment fault and analysis the hot picture atlas ; the text analyse the various kinds of possible factor which might effect the results of infrared diagnosing in electrical equipments, and propose correspondingly countermeasure against these factor in order to improve the accuracy of measurement ; finally, by using infrared diagnosing techniques analyse and diagnose the interior or exterior fault in part of transformers and arresters in electric network of si chuan, and the results obtained from the text accord with practice

    本文在紅外輻射的基礎知識上引出紅外診斷的基本原理，分析了紅外成像儀的成像原理；並從紅外診斷的角度研究了電氣設備的故障模式及其診斷的機理；研究了利用紅外熱像儀對電氣設備的故障進行診斷，獲取設備故障熱像圖譜並進行熱像圖譜的分析；對影響電氣設備紅外技術診斷結果的各種可能因素進行了分析探討，並針對這些干擾因數，提出了相應的對策，以提高檢測的準確性；論文最後應用紅外熱成像技術對四川電網中的部分變壓器和避雷器典型的內外部故障進行了診斷分析，得到與實際相符的結果。
  3. It is only using one high voltage cable to serve as the common one - turn primary winding for all the output transformers. in addition, the isolation voltage level for the transformers can be made very high

    使用超高壓絕緣的電纜線作為所有輸出變壓器單匝的原邊繞組，電源輸出之間的隔離電壓可以達到相當高的等級。
  4. Firstly, the thesis briefly reviews the history of voltage and reactive power control technology, focusing on the defects of the equipment in use. then, with the theoretical analysis and the discussion on voltage and the characteristic of power system as well as the basic principle of voltage and reactive power control, the thesis makes a research on the character of voltage and reactive power control and interprets the controlling regularity of substation. in addition, with the consideration of the changes of transformer tips and the combined influence of capacity groups and reactive power and voltage, the thesis makes adjustment suggestion to the different operating - zones of voltage and reactive power

    本文從降低網損和提高變電站自動化水平著眼，對變電站電壓無功控制應用方面的問題進行了研究，本文首先簡要回顧電壓無功控制的發展概況，著重指出了現有電壓無功控制裝置的缺陷；通過理論分析，在討論電力系統電壓、無功調節特點以及電壓無功總體控制原則的基礎上討論了變電站電壓、無功控制特性以及控制原理，給出了變電站電壓無功的控制規律；考慮了變壓器分接頭的變化及電容器組的投切對無功和電壓的綜合影響，針對電壓、無功的各種運行控制區域給出了相應調節策略。
  5. How to forecast transformer ' s fault ahead and find the fault reason quickly after the fault is a good way to increase work efficiency and lighten the economy losing

    如何提前對變壓器故障進行預測和在故障發生后迅速判斷故障原因是提高工作效率、減少經濟損失的一個重要途徑。
  6. Knowledge of transformer and inductor principles and applications. well know related standards and qualification tests

    熟悉高頻變壓器、電感工作原理及應用；了解相關國際標準及資格驗證測試。
  7. This thesis chooses b spline wavelet that adapts to the analysis of power system signal, and uses the wavelet transformer to analyze the magnetizing inrush current and inner fault current. a transformer microcomputer protection was designed in this thesis, and in the base of intermission angle principle, a new criterion was established, which pierces through the traditional method with accurate measurement of intermission angle, but analyses the wave by wavelet transform. this criterion is lower in hardware, so it will be realized in the existing hardware

    本文選擇適合電力系統信號分析的b樣條函數作為母小波，對勵磁涌流和內部故障電流進行小波分析，並設計微機型變壓器保護基本配置，在以往間斷角原理鑒別勵磁涌流的基礎上，突破傳統精確測量勵磁涌流間斷角的方法，直接對信號小波變換后的波形進行分析，建立一個新的鑒別勵磁涌流判據，該判據對硬體要求不高，可以在現有一般硬體平臺上實現；並編寫以b樣條函數為母小波的小波變換判據演算法程序。
  8. Dissolved gas analysis ( dga ) is one of the mainly technology methods to diagnose the internal malfunction in transformer. by request of dl / t722 - 2000, < guide to the analysis and the diagnosis of gases dissolved in transformer oil >, the component of h _ 2, c _ 2h _ 2, c _ 2h _ 4, c _ 2h _ 6, ch _ 4, co and co _ 2 is used to judge and analyze the internal malfunction in transformer

    本系統首先接收氣相色譜儀發送的數據信息，並對這些數據進行處理與分析，計算出譜圖數據的波峰高度、波峰面積、波峰起始點、基線等值，在此基礎上依據定量分析及故障診斷原理對變壓器進行診斷，得出結論。
  9. Since high tc superconducting ( hts ) tapes for practical applications became commercially available over the past few years, the development of superconducting power technology has achieved significant progress. it is foreseen that superconducting technology will be the prevailing high technology of the 21st century, and that superconducting power equipment will be commercialized soon, enjoying a large - scale worldwide market before 2010. china ' s economy is expanding fast, and the demand for electricity is increasing quickly. at the same time, higher electricity quality will be required. traditional power technology will no longer be able to satisfy future requirements, so superconducting power technology would be the best solution, leading a revolution in the power industry. the history, present status and prospects of superconducting power technology as well as the economic benefits and basic physics problems involved are reviewed

    人們認為，超導體在電力方面出現大規模應用的時間距離我們還非常遙遠.然而，隨著最近幾年來實用高溫超導材料的研製取得重大的進展，高溫超導電力技術的應用已經成為現實，預期將在2010年左右出現大規模的應用，並將帶來電力工業的革命.因此，下一個10年將是國際超導技術競爭最關鍵的10年.我國的經濟發展很快，電能需求量增加十分迅速，對電能質量的要求也越來越高.常規電力技術已經無法滿足我國電力發展的需要，超導電力技術是實現我國電力發展目標的必由之路.文章有代表性地介紹了超導電纜、超導限流器、超導磁儲能系統、超導變壓器和超導旋轉電機等的基本工作原理及研究發展歷史，並著重介紹高溫超導電力應用研究的現狀、應用前景、經濟可行性及基本物理問題
  10. The autor thought that for the main transformer, the load rate should be increased above 85 % ; and for the distributor transformers set with the electrial room, according to efficiency first principle, the load rate should be control at 40 % ~ 60 %

    作者認為：主變壓器設計選擇時，應考慮提高其負荷率達85 %以上；電氣室配電變壓器選擇時，應按效率優先原則為主，其負荷率控制在40 % ~ 60 %之間。
  11. 1 the company has excellent production condition and public facilities such as self - provide power plant supplying high voltage wire of 35 kv, two sets 16000 kva transformers in power station, one deep well with water discharge of tons per hour, water pool with water pcapacity of 150 tons, one water tower with 100tons, two boilers with four tons, three compressed air machines to make sure the requirement of production. the company located at no. 62haozhuang st. taiyuan city and is 0. 7 kilometer away from dongshan expressway and also 2. 5 kilometer away from the railway station. the company was also equipped with communication facilities for example international telephone and fax

    該公司具有良好的生產條件及公用設施：有自備電廠供給35kv高壓進線，變電站16000kva變壓器兩臺深井一眼，每小時出水50噸蓄水池150噸水塔1個，容量100噸4噸鍋爐兩臺，空壓機三臺，保證生產需求。公司位於太原市郝莊正街62號，距東山過境公路0 . 7公里，離車站貨場2 . 5公里，交通十分便利。有國際電話及傳真機等通訊設施。
  12. The clamping diodes conduct only once in a switching period, and the resonant inductance current is smaller in zero state, leading to a higher efficiency and reduced duty cycle loss. the operation principle of the improved converter and the comparison with the original converter are analyzed in this paper. the effect of the blocking capacitor in series with the transformer or resonant inductance is discussed, and a best scheme is determined

    本文將諧振電感和變壓器交換位置，使變壓器與滯后橋臂相連，這樣箝位二極體在一個開關周期中只導通一次，同時零狀態時諧振電感電流較小，有利於提高變換效率和減小占空比丟失，本文分析改進后變換器的工作原理，並與改進前的變換器進行對比，討論隔直電容在不同位置對變換器工作的影響，確定一種最佳工程方案。
  13. The effect of the primary and secondary winding widths on the power loss and energy storage are analyzed for the pcb winding pattern by using 2d - fem, it is demonstrated that when the primary and secondary have the same winding width, the transformer has the lowest ac - resistance and leakage, this suggests ways the designer can modify the winding arrangement to minimize the loss of transformer

    利用ansoft電磁場模擬軟體和本人開發的一維平面變壓器的繞組損耗計算程序對pcb繞組的並聯繞組的設計問題和pcb板繞組原副邊寬度相等問題進行了研究，提出了減少pcb板繞組的高頻損耗的設計方法。
  14. The principle of ac - dc - ac locomotive is that transformer transforms the high single - phase ac voltage from contact system to lower ac voltage first, then rectifier transforms this ac voltage to steady dc voltage, finally converter transforms this dc voltage to three - phase vfvv ac voltage as the voltage source for asynchronous machine

    交?直?交型電力機車系統的原理是：先將從接觸網獲得的單相交流高電壓經變壓器降壓后，再經整流器變換為平穩的直流電壓，直流電壓經逆變器變換為三相交流電壓，供給機車輪對上的牽引電機。
  15. In accordance with the technological difficulties encountered in the process of insulation supervision based on the dissolved gases analysis ( dga ), several kinds of model and method are presented to improve the reliability and precision of fault diagnosis of the power transformer. main research content includes : by deeply studying the common transformer faults diagnosing methods, such as three - ratio methods and improved electrical committee agreements, several shortcomings such as uncertainness judgment when the fault reasons, phenomenon and principles come out together while can not consistent to each other etc. for this reason, the old methods can not fully meet the need to engineering practical application. considering fuzzy relationship matrix can fully represents the causality between fault symptoms and fault types, when diagnosing complex equipments with multiple symptoms and fault causes such as power transformer, a synthetic fuzzy diagnosing model is firstly proposed to diagnose transformer ' s insulation faults based on dga in this paper

    本文針對應用油中溶解氣體分析方法進行變壓器絕緣監督時所遇到的主要技術難點，提出了提高變壓器故障診斷的準確性、可靠性的幾種模診斷方法，主要研究內容有：通過對判斷變壓器故障常用的三比值法和改良電協研法的深入分析，其診斷準確率較高，但對故障原因、故障現象和故障機理間同時存在不確定性和模糊性的變壓器等電氣設備的故障診斷，難于滿足工程應用的需要；在處理變壓器等結構復雜設備的多癥狀、多原因故障診斷時，模糊關系矩陣可以全面反映這種癥狀與故障類型間的因果關系，進而提出了變壓器故障診斷的模糊綜合診斷模型；同時作者還深入分析了模糊運算元的特性；針對常用的模糊評判結果的模糊集的集化方法的不足性，提出了將模糊綜合診斷與模糊規則推理結合起來進行故障診斷的方法，能達到較好的效果。
  16. " soft switching " is zero voltage switching or zero current switching, which the voltage ( or current ) of the switch varies by law of sine or quasi sine, the switch is on when its voltage reaches zero ( or switch is off when its current reaches zero ) by resonance. it makes switch loss is zero, so it can increase the operating frequency and raise power density, minimize the size of transformer and inductor

    「軟開關」是指零電壓開關或零電流開關，它是利用諧振原理，使開關變換器的開關管電壓（或電流）按正弦（或準正弦）規律變化，當電壓過零時，使器件開通（或電流自然過零時，使器件關斷） ，實現開關損耗為零，從而提高開關頻率，減小變壓器、電感的體積。
  17. Considering the compactness characteristics of dissolved gas analysis data, the achieved samples are pre - selected with the fuzzy c - means clustering method to solve the problem of long time consuming in parameter determination, thus a certain model extension ability is enhanced

    考慮到變壓器油中溶解氣體特徵空間的緊致性原理，利用模糊c均值聚類演算法對所獲取的樣本進行預選取，有效地解決了確定模型參數時耗時巨大的問題，並一定程度提高了模型的推廣能力。
  18. Based on comparison between the parallel - parallel and parallel - serial combination ttfc, a novel two - transistor forward converter with parallel - serial / serial combination is proposed. this converter reduces greatly the current overshoot of the primary side switches and the voltage overshoot of the rectifying diodes. moreover, the size and weight of the converter can also be reduced by interleaving technique and increasing frequency

    本文在對並-串型和並-並型雙管正激組合變換器進行了詳細比較研究的基礎上，提出了一種新型並-串串型雙管正激組合變換器，該組合變換器可以大大減小原邊開關管的電流應力和副邊整流電路中二極體的電壓應力；通過交錯控制及提高開關頻率，大大提高了變換器的功率密度。
  19. Yellow phosphorus copper transformers power transformers

    高原電力變壓器
  20. To reduce the emi, reverse reset of the diode are studied, and design way about spike - killers and saturable inductors witch can suppress voltage and current spikes are showed. in this thesis, a transformer clamping full - bridge dc / dc converter is presented to salve the high input voltage. in this chapter, the operating principle is analyzed and experimental results have been showed on the 2kw converter

    在處理高壓問題上，本文又提出了變壓器箝位高壓大功率dc dc全橋變換器拓撲方案，文中對其工作原理進行了分析，文中以一臺2kw的原理樣機對其工作原理進行了驗證，很好地解決了輸入電壓高的問題。
分享友人
分享到 Line

分享到臉書