高強度熱處理 的英文怎麼說

中文拼音 [gāoqiángdùrèchǔlǐ]
高強度熱處理 英文
maraging
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 強 : 強形容詞（強硬不屈;固執） stubborn; unyielding
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 處 : 處名詞1 （地方） place 2 （方面; 某一點） part; point 3 （機關或機關里一個部門） department; offi...
  • 理 : Ⅰ名詞1 （物質組織的條紋） texture; grain （in wood skin etc ） 2 （道理;事理） reason; logic; tru...
  • 高強度 : high strength高強度部件 high strength parts; 高強度材料 high strength material; 高強度磁場 high i...
  • 高強 : excel in; be master of
  • 熱處理 : [冶金學] heat treatment; heat treating熱處理保護塗料 heat treatment protective coating; 熱處理車...
  1. The heat treatment improves the tensile strength.

    熱處理能提高抗拉強度。
  2. The abvance of the high strength glass is that can prevent damage from the hard stuff collision or outside force, incase of damage, it will become pieces

    高強度玻璃通過加熱處理產生強化效果，能防止玻璃因硬物或外力碰撞而造成的損壞。萬一玻璃破損也會形成碎粒狀，確保安全。
  3. Having reacted with copper, paa becomes complex. the complex decomposes after heat treating and cause the increase in dielectric constant and reduction in dielectric breakdown strength. otherwise cu2o and cuo emerge from the complex, too

    N與cu反應后，形成絡合物，熱處理時自身降解，擊穿強度降低，介電常數提高； cz在熱處理后從絡合物離解出來形成cllo和cuzo 。
  4. High - strength structural steel plates and strips : products supplied in the heat - treated or controlled rolled condition

    高強度結構鋼熱處理和控軋鋼板鋼帶
  5. Then, the effect of heavily doped boron on ig of czochralski silicon was also investigated. it is found that no dz ( denuded zones ) were observed in the hb samples subjected to high one - step temperature, ramping annealing respectively. for conventional high - low - high three - step ig annealing, the dz becomes narrower and bmd density is higher in hb samples than that in lb samples, as a result of hb enhancing oxygen precipitation

    結果顯示，單步高溫熱處理時重摻硼樣品不能形成潔凈區；降溫退火中，降溫速度較為緩慢（ 3 / min ）時能生成一定量的氧沉澱，但沒有潔凈區形成；普通高?低?高三步熱處理過程中，形成明顯的潔凈區，但相對輕摻樣品而言，潔凈區較窄，氧沉澱密度明顯偏高，說明重摻硼樣品吸雜能力強。
  6. The base has features of high strength and hardness, owing to high quality material of first - class pig iron and casting of interal body. the main duriving shafts are durable in use through high cycle heat treatment of surface

    本機器的機座採用于等生鐵鑄造，強度高、剛性好、主要傳動軸類均經表面高周波熱處理，經久耐用。
  7. Because of its excellent properties, such as high strength, high module, wear resisting, and etc., sicp was added to ferroalloy as a reinforce phase. but the intrinsic difference between the bonds led to poor fabrication of the composites. in this paper, the effects of alloying, sintering, and heat - treatment on the properties and microstructures of sicp / ferroalloy - based composites were studied, : it was found that sic particles reacted with ferroalloy when sintered in 1100

    碳化硅因其高強度、高模量、耐熱、耐磨等優良性能而被作為顆粒增強體來制備鐵基復合材料，但因其共價鍵與鐵基體的金屬鍵之間的本質區別導致兩者復合困難，本文擬從基體合金化、燒結及熱處理工藝等方面對鐵合金基復合材料組織與性能的影響進行考察，具體內容如下：加入fe - cu - c基體中的sicp顆粒， 1100燒結時就已經開始發生分解，但反應不強烈，在顆粒表面鍍鎳可以延緩基顆粒與基體之間的反應。
  8. The unique continuous & highly intensified wire spirals system provides proper support and high rate of covering affer heat freatment as a whole

    專利技術獨特的連續彈簧系統高強度連續鋼絲床網經整體熱處理，具有良好支撐力和超高彈簧覆蓋率。
  9. Heat treatment for high strength bolts of rolling 42crmo steel

    鋼高強度螺栓的熱處理
  10. Cast and heat - treatment process of high strength aluminum alloy

    高強度鋁合金鑄造及熱處理工藝
  11. It is possible to suppress brittleness and increase the strength and toughness by optimizing heat treatment process especially for microalloyed steels 50crv. in addition, heat processing for microalloyed steels socrv was investigated in principle in the paper

    通過微合金元素產生的沉澱強化，可以彌補回火造成的強韌性的下降，設計最佳的熱處理綜合工藝將可以同時提高鋼的強度和韌性，同時還可保持一定的硬度。
  12. The results of the experiments show that the ti3al - tcll dual alloys, by vacuum - electron - beam weld, hot die forging and 680c / 12h, ac, heat treatments, have satisfied synthesis properties of intensity, plasticity, hardness. and also it is the feasiblie way. this will establish the supporting technology for the manufacture of the compress disk in the areoengine

    實驗結果表明，經真空電子束焊接ti _ 3al ? tc11雙合金經過熱模鍛造和680 12h ， ac或815 1h + 700 8h ， ac熱處理后，焊接區組織過渡均勻，可以使得焊縫處強度在室溫拉伸時高於ti _ 3al ，而在600拉伸時高於tc11合金，獲得強度、塑性、硬度均令人滿意的綜合性能，且是一條可行的工藝路線。
  13. In order to make investigators know about the current research state of preparation of the carbon / graphite materials with high density and strength from mesocarbon microbeads, and direct the research, development and production, in this review, the influence of preparaed mesocarbon microbeads from various raw materials and methods of preparation, ball diameter of carbosphere, preoxidation temperature and time, moulding pressure and time, heat treatment temperature and heating rate, holding time on the mechanical properties and microscopic structure of carbon / graphite product were discussed by us

    摘要為了對中間相炭微球制備高密高強炭石墨材料的研究現狀有所了解，並且對實驗和實際生產起到指導作用，本文通過參閱大量中外文獻，討論了不同原料及制備方法制得的中間相炭微球、炭微球的球徑、預氧化溫度及時間、成型壓力及時間、熱處理溫度及升溫速率、保溫時間對炭石墨製品的力學性能及微觀結構的影響。
  14. The results showed that the microstructure of as - deposited tbdyfe ii 1ms were amorphous and the crystal of tbfe2 were found in films after annealing at 500. annealing films in vaccum could improve the saturation magnetization ms and the susceptibility, decrease the coercivity and the saturaion field, and make the direction of the magnetic moments parallel to the film plane

    結果表明，制備態薄膜為非晶態結構，經過500真空退火熱處理后，薄膜出現了tbfe _ 2的結晶物，薄膜的矯頑力和外場的飽和磁場大大降低，飽和磁化強度增強，初始磁化率提高，易磁化軸轉向膜面。
  15. With the increase of silane content, the content of gelatin increased continuously and ntc phenomenon disappeared gradually. when the silane content reach a certain volume, the ntc phenomenon was eliminated completely, at one time, the content of gelatin keep stable. 4 、 heating treatment can improve ptc characteristic of composite and increase ptc intensity. when the temperature and time of

    隨著硅烷含量的增加凝膠含量不斷的增加， ntc現象逐漸消失，達到一定值時ntc現象消失，凝膠含量不再提高； 4 、熱處理可以改善導電復合材料的ptc特性，提高它的ptc強度，熱處理溫度為120 ，熱處理時間為30h時效果最為明顯。
  16. Plasma nitriding is an application way to metal surface and heating treatment based on the formed plasma by glow discharge. nitriding is a way of heating treatment, namely, metal accessory is put into activate nitrogen and the gas of low light pressure is ionized into energy electrons, high energy ions and high energy neutral atoms by the action of the electric field under a definite temperature and the time of the heat preservation

    等離子滲氮是利用輝光放電形成等離子體在金屬表面，熱處理方面的應用，滲氮是強化金屬表面的一種熱處理方法，是將金屬零件置於活性氮的介質中，在一定溫度和保溫時間下，低光壓氣體在電場作用下使之電離產生能電子、高能離子和高能中性原子。
  17. Secondly, choose the sample component, as different particle match of tungsten carbide and specifically heat treatment craftworks of solution and aging manufacture test piece, watch metallurgical structure of the test piece and do the tests of hardness and tension, at last do the abrasive wear test on the dynamic load abrasive wear test machine, analyze test datum, from the test data, conclusions are arrived that the hardnees of composite - alloy can be improved and wear - resistance be better by adding cr and other elements according to a given ratio

    本文對rp中速磨煤機耐磨件進行了運行與磨損情況分析，研究、提出了制備磨輥和盤瓦復合合金成分配比；並對製作的試件進行了固溶、時效等特定的熱處理工藝，觀察試件金相組織，進行機械強度試驗，最後做磨料磨損試驗，對磨損失效機理進行了深入的研究分析，對其耐磨性能與低合金鋼、高鉻鑄鐵進行了對比。
  18. The formation process of w - type ferrite underwent from oxide of metal, the m - type transition phase to final w - phase. when the heating rate was 5 / min, at 900 for 3 hrs and 1200 for 4 hrs, pure m - type and w - type ferrites were formed in air respectively. with heat treatment temperature increasing, crystal structure was more intact, the saturation magnetization increased and the coercive force decreased

    熱處理過程表明， m型鐵氧體直接由金屬氧化物反應形成，未經歷尖晶石中間相； w型鐵氧體形成由金屬氧化物到m相過渡相最終向w相的轉變；當升溫速率為5 min ，溫度在900 ，保溫3小時和1200保溫4小時，就分別形成單相m相和w相鐵氧體；隨著熱處理溫度的升高和保溫時間的延長，衍射峰變尖銳，結晶更完整，空心微球的飽和磁化強度增大，矯頑力減小。
  19. Production choosing titanium alloy after heat treatment could increase the high temperature intensity and wear off with hardness of hrc42

    選擇鈦合金材質生產，經熱處理后增加高溫強度及耐磨性，硬度hrc42 。
  20. Iron and steel. steel plate for boilers and pressure vessels. high yield strength heat treated alloy steels. grades and types

    鋼鐵.鍋爐及壓力容器用板材.高屈服強度熱處理合金鋼.等級和類別
分享友人
分享到 Line

分享到臉書