高縮率短纖維 的英文怎麼說

中文拼音 [gāosuōlǜduǎnxiānwéi]
高縮率短纖維 英文
high-shrink staple
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 縮 : 縮構詞成分。
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 短 : Ⅰ形容詞（空間、時間兩端之間的距離小） short; brief Ⅱ動詞（缺少; 欠） lack; owe Ⅲ名詞1 （缺點） we...
  • 纖 : 纖形容詞（細小） fine; minute
  • 維 : Ⅰ動詞1 （連接） tie up; hold together; link 2 （保持; 保全） maintain; safeguard; preserve; keep ...
  • 纖維 : fibre; staple; filamentary
  1. Experimental result shows that cavitation can destroy metal cyanogen preparation and chemical property of bearing cyanide wastewater is changed ; it intensify the fiber ' s adsorption progress and reduce the time of adsorption equilibrium, the general cyanide adsorption rate is increased 5 % or so, but it strength the different effect on different metal - cyanide negative ions ; strengthen effect of copper cyanide complex is stronger than zinc and iron cyanide complex, so ultrasonic wave may strength the fiber ' s adsorption processes

    實驗結果表明，功率超聲的空化作用能破壞金屬氰配合物鍵，從而改變含氰廢水的化學性質，另外也可縮短吸附平衡時間，強化纖維的吸附過程，使總氰的吸附率可提高5 %左右；功率超聲對不同金屬氰配合物離子的強化效果是不同的，對銅氰絡離子的強化效果要強于鐵氰、鋅氰絡離子，所以功率超聲可以強化纖維的吸附過程。
  2. Based on the characteristics of silicon whisker, the research on the modification of pa6 by silicon whisker sio2 - jx was made, and the result showed that the tensile strength, impact strength, brinell hardness, and heat resistance increased with the increase of the content of the whisker ; sio2 - jx could replace short glass fiber in the modification of pa6, improving the heat distortion temperature, removing the appearance of glass fiber, reducing shrinkage and the cost

    摘要利用晶須矽纖維狀的特性，對其填充于龍玻纖改性進行研究，結果表明，隨晶須用量的增加，材料的拉伸強度、沖擊強度，布氏硬度、耐熱溫度均得到提高；晶須矽可取代短玻纖使用，提高熱變形溫度、消除玻纖外露，降低收縮率及生產成本等。
  3. Regarding the lcm filling process as the newton fluid through fibrous reinforcements, the permeability of preform determines the saturating of resin in fiber, and has effects on the curing process and the quality of products. based on the darcy ' s law, the theoretical model of permeability measurement was established. and the influence of different testing methods and major process parameters such as fabric structure, fiber volume fraction, injection pressure, flow rate and resin viscosity on preform permeability were investigated in details

    文中首先根據達西定律建立了滲透率測量的理論模型，深入研究了不同的測試方法及主要工藝參數（纖維織物織構、纖維體積含量、充模壓力、流動速度、樹脂粘度）對滲透特性的影響規律，發現多孔介質增強材料的滲透率主要取決于纖維織物的結構形式，預成型體孔隙分佈及其體積分數、壓實性對滲透率有較大的影響，提高充模壓力和流動速度可以縮短充模時間，在一定程度上可以提高滲透率。
分享友人
分享到 Line

分享到臉書