高負壓 的英文怎麼說
中文拼音 [gāofùyā]
高負壓
英文
high negative pressure-
On the basis of that, numerical simulations have been carried out on full - scale cube model with three types of parapets. the caparison of with and without parapets shows that three types of parapets can significantly reduce high negative suction peaks on zones susceptible to wind pressure. formulas have been proposed about the height of those parapets
在此基礎上對方塊模型屋面分別設置3種女兒墻進行了數值模擬，與未設置女兒墻的模擬結果進行了比較分析，結果表明上述女兒墻都能較明顯地降低屋面風壓敏感區的負壓峰值，並給出了相應的女兒墻高度限值公式。Finally, with caparisons of that three parapets properties cantilevered parapets has been adopt to the steel structure of light - weight buildings with gabled frames, numerical simulations have been carried out with that buildings, results of simulations show that device can also significantly reduce the area - averaged coefficient of wind pressure and high negative suction peaks on zones susceptible to wind pressure. formula has been proposed about the height of that parapet
最後通過三種女兒墻的性能比較確定對門式剛架設置懸挑女兒墻進行數值模擬，結果同樣表明懸挑女兒墻能明顯地降低門式剛架屋面風荷載敏感區的負壓峰值及屋面風荷載體型系數，並給出了女兒墻高度限值公式。Through studying it is shown that in chagan sag, the geothermal gradients in the center are higher than those around the sag margin and major factors influencing the characteristics of temperature field distribution are the property of geotectogenesis and the differences in tectonic portion, lithology and underground water behaviour ; there are three types of mudstone compaction, i. e. normal compaction, undercompacition and overcomepaction ; there are two pressure systems in sandstone reservoirs, i. e. normal pressure and negative pressure systems and the strata ' s being uplifted and denuded is the key factor leading to the formation of the negative pressure system in reservoir ; and the distinctive temperature - pressure field characteristics in the sag are possessed of important petroleum geological significance in hydrocarbon source maturity, hydrocarbon generation, widening on oil and gas exploration domain and selecting exploration targets, etc
研究表明，查干凹陷中心的地溫梯度高於凹陷邊緣，大地構造性質及所處構造部位、巖性與地下水活動的差異是影響凹陷地溫場分佈特徵的主要因素；泥巖壓實存在正常壓實、欠壓實和過壓實三種類型，砂巖儲層段壓力類型可分為正常和負壓兩個系統，地層抬升剝蝕是導致儲層負壓系統形成的主導因素；凹陷獨特的溫壓場特徵對烴源巖成熟、油氣生成、油氣勘探領域的擴大及勘探方向的選擇等具有重要的油氣地質意義。The air - flow field in the stripping unit can be adjusted easy by changing the rotation speed of fan which is benefit to reduce the grain losses, it was found during experiment that the cross - flow fan can diffuse some of mog ( material other of grain ) and diffuse it in a certain direction which is useful to satisfy the working condition for driver and lighten working load of the threshing unit of the combine harvester candidate and speciality : peng shengmin ; machinary design and theory supervisor : prof. zhang huiyou
該裝置可以通過控制橫流風機的轉速，使裝置內氣流在有控制的情況下排出裝置外，改善了裝置內流場狀態，提高了裝置喂入口處的負壓，這對減少摘脫裝置的落粒損失，有著重要意義。由於橫流風機的除雜，可以減輕機器的復脫和清選負荷。安裝橫流風機后可以對裝置的出風口處灰塵進行有效導引，改善駕駛員的工作條件。Although angiotensin is generally acknowledged to be responsible for renovascular hypertension, at least in the early phase, there is no consensus regarding the role of the renin - angiotensin - aldosterone system in patients with primary hypertension, even in those with high pra
普遍認為，血管緊張素對腎血管性高血壓負有責任，至少是在早期，但是，在原發性高血壓病人，甚至是pra升高的原發性高血壓病人中，人們對腎素-血管緊張素-醛固酮系統所起的作用尚無一致意見。The production and operations of the company suction fan and water poon cooling equipment, known as the new generation of wang ventilation cooling, cooling dust removal of the air smell, improve air quality with a good performance, can be widely used in industrial production, plastic injection, automobile maintenance, petrochemical, paint electroplating, logistics, warehousing, horticultural greenhouses, public facilities and other fields
公司生產經營的負壓式風機及水濂降溫設備，號稱新一代的通風降溫王，對于降溫除塵、去除空氣異味，提高空氣質量具有良好效能，可廣泛應用於工業廠房、塑料澆注、汽修保養、石油化工、烤漆電鍍、物流倉儲、園藝溫室、公共設施等領域。The production and operations of the company suction fan and water poon cooling equipment known as the new generation of wang ventilation cooling cooling dust removal of the air smell improve air quality with a good performance can be widely used in industrial production plastic injection automobile maintenance petrochemical paint electroplating logistics warehousing horticultural greenhouses public facilities and other fields
公司生產經營的負壓式風機及水濂降溫設備，號稱新一代的通風降溫王，對于降溫除塵、去除空氣異味，提高空氣質量具有良好效能，可廣泛應用於工業廠房、塑料澆注、汽修保養、石油化工、烤漆電鍍、物流倉儲、園藝溫室、公共設施等領域。The company has a good ventilation cooling engineering team, the improvement of adverse operating environment, improve ventilation cooling effect, especially in the process of suction fan + wet curtain cooling ventilation works, years of industry experience, to offer our customers satisfied with the products and professional services
公司擁有一支優秀的通風降溫工程技術團隊，在改良各種惡劣作業環境，提高通風降溫效果方面，特別是在承接負壓式風機降溫濕簾通風工程方面，有多年的行業經驗，可為客戶提供滿意的產品和專業的服務。High temperature resistant measure is taken to extend its service life significantly in comparing with the tube still hot air furnace, whereas, cross brushing of heat sink by the smoke and negative pressure smoke exhaust are used to ensure a clean heat exchanging position with stable thermal performance
該爐採取了耐高溫措施，從而使其壽命比列管式熱風爐大大延長，並採用了煙氣縱向沖刷散熱片和負壓式排煙方式，換熱部分不積灰塵，無須清理，熱性能穩定。Adopt advanced technic of f4 whole cold - press to moulding and heat melt to process to make, let the lining no slot to link withal cheek by jowl connect with exterior metalpipes wall, in the state of allowwing to work keep to distort in - phase, thereby to enhance using - life of lining in the working status of opposite high temperature high vacuum, stop the ecumenic pad fluorin pipes using in condition of cold and heat alternate and minus tension to come into being the matter of padding fluorin floor shrivel to jam the flowway and plastic rip, its perfect choice use to transport medium of strong corrosive strong oxidation by modern chemical - industry corporation
採用氟塑料f4整體冷壓成型及熱熔加工等先進技術製造，使內襯層無縫搭接且與外層金屬管壁緊密粘接，在允許工作狀態下能夠保持同步變形，從而提高了襯里層在相對高溫高真空度的工況下的使用壽命，杜絕了一般襯氟管在冷熱交替，及負壓的條件下使用易產生襯塑層鼓癟阻塞流道及塑料拉裂的問題，是現代化工企業在輸送強腐蝕強氧化介質理想的選擇。The results show that the heat preservation coating and its proper thickness are favorable to the enhancement of filling mold speed of aluminium alloy ; the higher the pouring temperature is and the larger the ratio of hollow areas of vertical pouring is, the faster the speed of filling mold of aluminium alloy is ; if the mold is too thick or too thin, it may decrease the speed of filling mold ; the proper length and the area of vertical pouring are favorable to the enhancement of the speed of filling mold ; although negatire - pressure may improve filling the speed, too high negatire - pressure may enlarge the flaw in casting
結果表明：保溫塗料及一定的塗層厚度有利於提高鋁液的充型速度；澆注溫度越高、直澆道空心面積率越大，鋁液充型速度越快；模樣厚度太厚或太薄，均會使鋁液充型速度降低；一定的直澆道長度及直澆道面積有利於提高鋁液的充型速度；施加負壓會使鋁液的充型速度大大提高，但負壓過大會增大鑄造缺陷。The construction methods and caving protection measures for punching high thick and loosen soft coal seam in luling coal mine no. 2 dark tilt well in huaibei coal mine area are introducded. they include small section enlarged after the heading caving, high negative pressure and multi - raw drilling holes and strenous drawing - off, concentrated cross drill holes, cutting while drawing - off and putting the metal frame away
介紹了淮北礦區蘆嶺煤礦2主暗斜井採用小斷面導硐后刷大、高負壓多排鉆強抽，密集交叉鉆孔邊掘邊抽及設置金屬骨架施工方法和防突措施揭穿高突特厚松軟煤層。Three - phase dry - type distribution transformers 50 hz, from 100 to 2500 kva with highest voltage for equipment not exceeding 36 kv - determination of the power rating of a transformer loaded with non - sinusoidal current
小於36kv設備的最高電壓值為50hz 100 - 2500kva三相干式配電變壓器.負載非正弦電流的變壓器額定功率的測定The results show that, composite could be fabricated on the complicated surface by means of sodium silicate sand mold combination with vacuum infiltration process. when the substrate was 10 mm, composite layers reached 3 mm to 5 mm in thickness with high strength interface and less casting defect. microstructures of grey cast iron and low chromium cast iron matrix composites with various volume fraction has been analyzed
結果表明：用水玻璃砂型（芯）加負壓鑄滲的工藝能夠實現復雜表面（曲面）顆粒增強復合材料的制備，澆注方式簡單可靠，基材厚度在10mm時，復合層厚度能達到3 5mm ，且復合層鑄造缺陷少，復合效果好，界面緻密而且結合強度高。After a long - term research, we introduced metal - mesh into ptfe thin lining with a particular technology, which enables it not to free expand or contract with the variation of temperature, improve its pressure and vacuum resistance capacity
本公司經過長期研究，於1988年採用特殊技術，將金屬網引入ptfe薄層內部，使ptfe層熱脹冷縮降低到與鋼外殼相一致，同時還增加了強度，提高了耐正、負壓性能。After the coke being puted into the coke - quenching device, the lid of the device should be shut at once. while the suction pump, refrigeration compressor, high pressured water circuling pump are started, the subpressure will be produced by the burning coke. then, in the vacuum, the coke will be extinguished in a flash. the burning of the coke instantly, still, produces a large quantity of heat which can be taken away by circulating water in refriger and the interlayer, after that, the temperature will fall to 60oc, even lower. in this condition, the coke will be pushed out to be stored, thus, the coke won ' t rekindle
當焦炭推上攔焦車進入熄焦器后，立即關閉罐蓋，同時啟動真空泵、冷凍機、高壓循環水泵，這時，燃燒著的焦炭就會因真空泵把熄焦器內抽成負壓，由於缺氧，使焦炭熄滅，雖然煤炭在瞬間被熄滅，但由於焦炭生成過程中所產生的大量的熱量還存在，這時，冷凍機和夾層中的循環水的工作就會把焦炭中的熱量帶走，使之在短時間內將溫度降到60以下，在這種狀態下把焦炭從熄焦器內推出入庫，焦炭就不會復燃。Three phase dry type power transformer, which make it with those features : safety, reliability, and energy saving, fireproof, flameproof, simple maintenance etc., the design is advanced ; the structure of products is reasonable and the outline is fine, the main performances of the products are much better than the national standards, for example, partial discharge level no - load loss, on - load loss, noise level, it is adaptable for application on heavy humidity and severely pollute places which are near to lake, sea and rive, as well as, high demand - fireproof, heavy load capacity place, such as : high building, airport, station, port, underground, hospital, electrical power station, metallurgy, shopping center, residential area and petroleum chemical industry, nuclear power station, nuclear - powered submarine
非包封線圈三相干式變壓器，具有安全可靠節能防火防爆維護簡單等優點。其設計先進結構合理外形美觀。主要性能指標均優于國內標準，如局放水平空載損耗負載損耗噪聲以及能適應高溫度環境使用等，可安裝在靠近湖海河邊污穢潮濕的環境及防火要求高負荷較大的地區，適用於高層建築機場車站碼頭地鐵醫院電廠冶金行業購物中心居民密集區以及石油化工核電站核潛艇等場所。Team spirit and take challenge and pressure
責任心強，能夠承受高負荷的工作壓力A new drive circuit for igbt is designed. it features high switching frequency, high driving power, simple - structure and reverse - turn - off
論文中還設計了一種新型的igbt驅動電路，它具有開關頻率高、驅動功率大、結構簡單且具有負壓關斷的特點。The effect of high negative pressure suction on children with chronic suppurative otitis media
高負壓耳抽吸治療兒童慢性化膿性中耳炎療效觀察分享友人