齒輪試驗機 的英文怎麼說
中文拼音 [chǐlúnshìyànjī]
齒輪試驗機
英文
gear test machine- 齒 : Ⅰ名詞1 (牙; 牙齒) tooth 2 (物體上齒形的部分) a tooth like part of anything 3 [書面語] (年齡...
- 輪 : Ⅰ名1 (輪子) wheel 2 (像輪子的東西) wheel like object; ring; disc 3 (輪船) steamer; steamboa...
- 試 : 名詞(古代占卜用的器具) astrolabe
- 驗 : 動詞1. (察看; 查考) examine; check; test 2. (產生預期的效果) prove effective; produce the expected result
- 機 : machineengine
- 齒輪 : gear [rack; toothed] wheel; (toothed) gear; wheel gear
- 試驗 : trial; experiment; test
-
After canvassing the basic theories and methods of reliability and optimization design of the transmission system, analyze the designs of the v - belt transmission, arc cone gear and disk spring separately. it is propitious to raise efficiency, improve capability, increase reliability, and decrease cost and so on
在研究了機械可靠性優化設計基本理論和方法之後,分別分析了v型帶傳動、圓弧錐齒輪、液壓卡盤碟型彈簧的可靠性優化設計,對其進行針對性的研究,並通過試驗對設計結果進行檢驗。In order to obtain dynamic characteristics of transplanting mechanism with elliptic planetary gears of high - speed rice transplanter, a test bed to measure dynamic parameters for high - speed transplanting mechanism is developed
摘要為了得到高速插秧機橢圓齒輪行星系分插機構的動力學特性,研製了高速分插機構動力學試驗臺。These characteristics and phenomenons have effect on the quality of gear pump, and it is difficult relatively to research them by theory. at present the research is limited to the phase of examination testing. theoretic research of the characteristics and the phenomenons of polymer gear pump are blank in china when the gear pump feeds the viscous polymer liquid of chemical flow with high temperature and high pressure
齒輪泵除具有流量和容積效率、扭矩和機械效率、功率和總效率等基本特性外,還存在著困油、噪聲和氣穴等現象,這些特性和現象直接影響齒輪泵的質量,對斜齒齒輪泵的這些特性和現象的理論研究難度較大,目前大多仍局限於實驗測試研究階段,而聚合物齒輪泵在輸送化工流程中的高溫、高壓的粘流態聚合物時特性的理論研究在國內基本還處于空白。Gearbox of off - grid wind turbine generator system part 2 : test method
離網型風力發電機組用齒輪箱.第2部分:試驗方法4 ) the gear pump is tested both in the manufactory and in the pet equipment
4 )對高參數齒輪泵樣機作了運轉試驗並對其生產現場運行進行了測試。Acceptance code for gears - determination of mechanical vibrations of gear units during acceptance testing
齒輪驗收法規.驗收試驗期間齒輪機構機械振動的測定Acceptance code for gears - part 2 : determination of mechanical vibrations of gear units during acceptance testing
齒輪驗收規程.第2部分:驗收測試過程中齒輪裝置機械振動的測定The article takes the whole - life experimentation of the gear for example, points out that the sustainable development of whole - life design must base on the study of few sampling, and brings forward two kinds of strategies of the study on the few sampling : the study on the numerical simulations and the study on the virtual prototype technology
摘要以齒輪全壽命試驗為例,指出全壽命設計可持續發展必須依賴于小子樣系統研究,並提出小子樣系統的2種研究策略,即數值模擬研究和虛擬樣機研究。Domestic and abroad standard and test information of alimak co. for braking distance of antifalling safety device of construction hoist are analyzed. the writers study the application and inspection situation of safety device in our country and put forward a suggestion of reasonable range of braking distance for safety device with gear cone drum
本文分析了有關施工升降機防墜安全器制動距離的國內外標準條文和alimak公司的試驗資料,結合我國施工升降機防墜安全器的應用和檢測情況,提出了修改齒輪錐鼓形防墜安全器制動距離合格範圍的建議。At last, a design example problem of column - gear speed reducer is made. contraposing design character of gear driver, attain the solution of mathematic model of robust optimal design and compared to that of common optimal design. the results show that the gear driver by robust optimal design is higher power to resist disturb and good quality stability and high reliability
為了證明隨機模擬試驗的穩健優化設計方法的正確性、可靠性和實用性,本文以某二級圓柱齒輪減速器為設計實例,針對齒輪傳動的設計特點,運用隨機約束方向法對穩健優化設計數學模型進行求解,並將一般優化設計結果與穩健優化設計結果進行比較、分析,結果表明穩健優化設計得出的齒輪傳動系統抗干擾能力強,質量穩定性好、可靠性高。分享友人