adhesive coefficient 中文意思是什麼

adhesive coefficient 解釋
粘著系數
  • adhesive : adj. 黏附性的，膠黏的。n. 膠合劑，黏合劑。adv. -ly ,-ness n.
  • coefficient : adj. 共同作用的。n. 1. 共同作用；協同因素。2. 【數，物】系數，率；程度。
  1. It has been discovered that ( 1 ) in the region between 100 - 350 the friction coefficient is lowering along with the swing of temperature ; ( 2 ) the friction coefficient is the highest at the temperature of 500, and adhesive wear occurred ; ( 3 ) the global graphite grain layer appeared at the surface of wear scar at 450n and 300, and played an extremely good effect of lubrication, thus makes a fairly lower wear at the temperature of 300

    發現： （ 1 ）在100 ~ 350區間，隨溫度的升高，摩擦因數在降低； （ 2 ）在500時，摩擦因數最高，且發生了粘著磨損； （ 3 ）在450n ， 300時，磨痕表面出現了球狀的石墨顆拉層，這起到了極好的潤滑作用，使得300時，磨損較低。
  2. The repair effect was compared with various type of repair parameters such as patch thickness young ' s modulus and thickness young ' s modulus of adhesive layer. in the chapter iv, a thermalstatic mechanical loading analysis of the repair problem was made. for the single side repair, the patch material having the maximum mismatch in the coefficient of thermal expansion with that of the crack aluminum plate provides the better damage tolerance capability for single - side crack in the panel

    模擬計算表明：粘膠模量增大， j積分值降低，修補效果與粘膠模量有關；隨著粘膠厚度的增大，修補模型的j積分值略有增大后再逐步減小，應合理選擇粘膠的厚度，盡量避免選擇j積分較大值時的粘膠厚度；隨著補片厚度的增加，修補模型的j積分值逐漸增大，到達一定量后又開始減小，因此補片的厚度需要合理選擇。
  3. In the process of emergent brake, relations among brake press, parameters of the entire vehicle and adhesive coefficient between tire and road surface influence the distribution of brake disc friction temperature field greatly

    在緊急制動過程中，制動壓力、整車參數以及輪胎與路面間附著系數之間的關系對制動器摩擦溫度場分佈有重要的影響。
  4. The work of cohesion increased with the enhancement of wettability, but the bending strength of the welding specimens did not. when wc or mo was added the mode was adhesive rapture ( ii ) because of the difference between the thermal expansion coefficient of wc, mo and ni. the bending strength was high when iv rapture was occurred

    研究發現粘附功隨潤濕性的改善而提高，但是焊接試樣的抗彎強度並沒有呈現明顯的這種趨勢；由於wc和mo與金屬ni熱膨脹系數相差較大，焊接試樣斷裂方式為內聚型斷裂（型斷裂） ，抗彎強度較低；以型方式斷裂的體系具有較高的抗彎強度。
  5. On adhesive friction coefficient with fractal geometry

    粘著摩擦系數的分形幾何研究
  6. Aim at the shortage in actual application that the frp pipe flange joint with the steel pipe and steel parts, in consideration of the special advantage of the adhesive boned joint, put forward the method that the steel flange adhesive boned steel pipe or steel part after the steel flange instead the frp pipe flange, or the frp pipe adhesive boned direct with the steel and steel part, it can reduce the stress concentration problem that cause from the different of the descend speed and the hot bulge or freeze coefficient in the applied process. thus reduce the damage number and the maintenance costs of the piping, so this method can have the greatly actual application value

    針對玻璃鋼管道與鋼管及鋼管件之間法蘭連接方式在實際應用中的不足之處，考慮到膠接連接的獨特優勢，提出如用鋼法蘭代替玻璃鋼法蘭與玻璃鋼管道膠接后，再與配套的鋼管及鋼管件進行連接，或玻璃鋼管道直接與鋼管（件）進行膠接連接，則可減少玻璃鋼管道在應用過程中與鋼管（件）連接后因沉降速度及凍脹系數均不同而產生的應力集中問題，減少管道的損壞次數及維護成本，有很大的實際應用價值。
  7. The paper also discusses the influential factors on the maneuverability and stability, such as, lateral stable pole, the position of gravity center, road adhesive coefficient, and so on, which provides the basis for the designing and safe running of the coach - bus

    同時，討論了安裝橫向穩定桿、輪距變化、重心高度變化及道路附著狀況等對大客車高速操穩性的影響，從而為客車的設計、安全運行等提供了寶貴的依據。
  8. This machine has great feeding ability, easy to be regulated, can be fed with fixed quantity under control of time delay relay ; it is divided into one - way feeding and bidirectional feeding in terms of feeding direction, suspending type and seating type in terms of installation ; in order to assure precision of feeding, roller encapsulation is equipped to increase frictional coefficient between adhesive belt and rollers ; the rectangle discharging mouth has large dimension which can prevent humping up materials ; this machine has close structure, reliable application and can be easily repaired because it has many similar parts with belt type conveyor

    該機給料能力大，調節給料量方便，又可在時間繼電器的控制下定量給料按給料方向該機可分為單項給料和雙向給料，按安裝方式又分為吊掛式和座式為了保證給料的精度，主動滾筒包膠，以增加膠帶與主動滾筒的摩擦系數料倉矩形卸料口的尺寸大，物料不易起拱該機結構緊湊，使用可靠，它與帶式輸送機有許多通用部件，故維修方便。
分享友人
分享到 Line

分享到臉書