allowable deformation 中文意思是什麼
allowable deformation
解釋
容許變形- allowable : adj. 可容許的，可承認的，不礙事的，正當的。 Two mistakes are allowable in this game. 這種游戲允許犯規兩次。adv. -bly
- deformation : 變形,走樣
-
Using the optimum calculating method, some important technical parameters could be determined, that is, optimum supporting force, allowable deformation of rock mass, cross section area of u - shape set, pre - tight force and diameter of the bolt as well as torque to provide optimum supporting force
用這一計算方法能求出巖石恆阻支護的重要技術參數，即最優（小）恆阻支護力、圍巖最大允許變形量、恆阻u型鋼支架的截面積、聯接螺栓的預緊力和直徑及最優支護力的擰緊力矩。 -
Allowable value of deformation of steel member
鋼構件變形容許值 -
For existing building, however, subgrade deformation usually exceeds the allowable subsoil deformation that is anticipated in design phase because of many reasons, which is especially serious in soft soil area. and this produces additional stress not considered in design stage and reduces the reliability of superstructure
對在役結構而言，地基往往會因為各種原因而出現超出設計預期的變形，尤對軟土地區上建築物的影響更為突出，導致上部結構產生設計未考慮到的附加效應，降低上部結構的可靠性。 -
In this paper, the cold die forging technology of the counter gear was analysed, the cold die forging was designed, the blank dimensions and the figure were calculated and choosed, the allowable deformation degree was checked, the equipment for the deformation was selected, the blank treatments before the cold die forging were draw up and the die structure of the cold die forging was designed
分析了計數器齒輪的冷模鍛工藝，設計了冷模鍛件圖，計算及選用了毛坯尺寸及形狀，驗算了許可變形程度，選擇了變形用的設備，擬制了冷模鍛前的毛坯處理及設計了冷模鍛模具結構。 -
Abstract : in this paper, the cold die forging technology of the counter gear was analysed, the cold die forging was designed, the blank dimensions and the figure were calculated and choosed, the allowable deformation degree was checked, the equipment for the deformation was selected, the blank treatments before the cold die forging were draw up and the die structure of the cold die forging was designed
文摘:分析了計數器齒輪的冷模鍛工藝，設計了冷模鍛件圖，計算及選用了毛坯尺寸及形狀，驗算了許可變形程度，選擇了變形用的設備，擬制了冷模鍛前的毛坯處理及設計了冷模鍛模具結構。 -
Allowable value of deformation of structural member
構件變形容許值 -
This topic makes attempt to make spatial relationship between tunnel construction and pipeline through surface settlement to control pipeline deformation indirectly, that is, surface deformation value is deducted reverse by allowable deformat ion value
即根據管線的允許變形值來反推出地表允許的變形值。本課題在這方面做了一些嘗試。即：確定地表最大沉降值whx作為目標控制值，即通過控制地表沉降來控制管線的變形。 -
Based on the experiment information and engineering application, the allowable deformation and cracked tensile force of the pipe joints are presented
根據實驗研究和工程實踐，提出了用於供水管道抗震計算的管道接頭允許位移和開裂拉力等參數。
分享友人