arc electrode 中文意思是什麼
arc electrode
解釋
電弧極-
Application of plc in control system for large electrode arc furnace
在大型電弧爐控制系統中的應用 -
Arc welding equipment - part 11 : electrode holders
弧焊設備.第11部分:電極握桿 -
" ubridge brand " marble mostly to use in slagging powder with drug cover welding electrode. improve slag basicity, steady arc, increase surface strain. it also used on architecture industry
粵橋牌大理石粉為白色或淺灰色礦粉,主要用於藥皮焊條等焊接材料的造渣造氣劑,可提高熔渣堿度穩 -
Arc steel - making stove ' s electrode elevating control system
電弧煉鋼爐電極升降智能控制系統 -
Abstract : with the aids of computer ' s hardware, executive mechanism of weld arc length automatic controller of all - position pipe welder and additional software, an automatic system for arc striking has been developed, in which touch - starting method using tiny current is introduced. utilizing this method, the ablation ratio of tungsten electrode and tungsten inclusion ratio of welded seam is far smaller than normal touch - starting method. and the successful ratio of arc striking is high
文摘:用全位置自動焊管機弧長自動控制系統的計算機硬體和執行機構,僅增加部分程序,設計了採用小電流接觸引弧法的自動引弧系統,鎢極燒損和焊縫夾鎢遠小於普通的接觸引弧方式,引弧成功率很高。 -
Electrode holder for manual arc welding with coated electrodes safety rules, specifications and tests
使用藥皮焊條手工焊接用焊鉗.安全規則規范和試驗 -
Based on the theory of piecewise - linear, the paper carries through the research of model self - adaptive control to electric arc - furnace electrode regulator system ( eafers ), and the digital self - adaptive control law of reference model is deduced. then, we designed the software simulation system of eafers according to the law, though which we studied the character of eafers. finally, a set of physical model of eafers, which is realized by hardware circuit, is designed according to the former research
本文首先應用分段線性化理論,對電弧爐電極調節系統的模型參考自適應控制演算法進行了研究,推導出全數字化的模型參考自適應律;然後根據推導出的自適應律成功的設計出了的軟體模擬系統,用軟體對電弧爐電極控制進行了模擬研究;最後利用電子電路構造出一套完整的電爐煉鋼電極控制硬體模擬系統,對電爐電極調節進行了實驗室電路模擬研究。 -
A production rate as high as 15 % is obtained under the condition of 150torr helium partial pressure, 300a arc current and quick electrode approaching speed as soon as possible. 2
在盡可能快的推進石墨棒的條件下,弧電流300a 、氦氣壓150torr 、無氦氣流時c _ ( 60 )粗品的產率最高,約為15 ; 2 -
Metallic electrode arc lamp
金屬電極弧光燈 -
The variable polarity power supply circuit uses two stages full - bridge inverter, the former inverter is regarded as a constant - current source with fast dynamic response, and supplys energy for the second one, and the latter one is to produce variable polarity current excellently, and low - frequency pulse current by variable polarity power supply is used to reduce input energy and control the shape of weld bead while welding. a series of high - frequency pulse current is superposed on direct - current - electrode - negative ( dcen ) current through the high - frequency pulse power supply, which is used to compress the arc and improve process of crystallization
其中變極性電源採用二次全橋逆變結構,一次逆變提供快速的響應速率並給二次逆變提供能量,二次逆變提供良好的變極性性能,使輸出能量最優化,並用其低頻電流特性減小電弧線能量,控制焊縫成形;高頻脈沖電源提供的高頻電流疊加在反極性電流dcen上,利用電流的高頻特性壓縮電弧,改善焊縫金屬結晶過程。 -
Due to two work states - - - arc burning and short current - - - existed in welding process of consumable electrode welding, and different control objectives in these two states, two close - loop feedbacks are designed in the control system : welding voltage feedback and welding current change rate feedback
根據熔化極co2焊機具有燃弧和短路兩種工作狀態,且兩種狀態下控制目標不同的特點,在控制系統中設計了雙閉環反饋:焊接電壓反饋及焊接電流變化率di / dt反饋。 -
Paste products have broad applications, such as the electrode paste, which can be used as the electricity - conducting materal in the sumerging ? arc furnace for producing calcium carbide and ferroalloy, and the anode paste, which is used as the electriciyt - conducting anode in aluninum electrolysis cell
糊類產品用途廣泛,其中電極糊可作為自培電極在生產電石、鐵合金的礦熱爐上作導電材料,陽極糊可作為鋁電解槽的陽極導電材料。 -
The electrode angle should be adjusted to a position that tends to overcome arc blow
焊絲的角度應調整至克服磁偏吹的方向 -
Welding consumables - wire and tubular cored electrodes and electrode - flux combinations for submerged arc welding of high strength steels - classification
焊接消耗品.高強度鋼的埋弧焊用焊絲和藥芯焊條和焊條焊劑組合物.分類 -
Safety requirements for arc welding equipment - part 11 : electrode holders
弧焊設備安全要求第11部分:電焊鉗 -
Influence of rotary arc on the feature and electrode erosion of spark switch
旋轉電弧對火花間隙開關電極燒蝕的影響 -
Welding electrode holders for arc welding
電弧焊用焊條鉗 -
Arc welding equipment - part 11 : electrode holders iec 60974 - 11 : 2004 ; german version en 60974 - 11 : 2004
電弧焊設備.第11部分:電極握桿 -
Rubber insulated cables - rated voltages up to and including 450 750 v - part 6 : arc welding electrode cables
額定電壓450 750v及以下的橡膠絕緣電纜.第6部分:電弧焊電極電纜 -
Amendment 2 - rubber insulated cables - rated voltages up to and including 450 750 v - part 6 : arc welding electrode cables
橡皮絕緣電纜.額定電壓450 750v及以下.第6部分:弧焊電極電纜.修改件2
分享友人