bonnet valve 中文意思是什麼
bonnet valve
解釋
帽形閥-
Wcc valve bonnet and internals will be manufactured with 300 series ss and / or 21 / 4 cr
Wcc閥門的閥帽何閥內件採用300系列不銹鋼和/或21 / 4鉻製造。 -
Wcc valve bonnet and internals will be manufactured with 300 series stainless or 21 / 4 cr material
Wcc閥門的閥帽何閥內件採用300系列不銹鋼和/或21 / 4鉻製造。 -
A complete list of replacement components can be found on the preceding page. bonnet assemblies and seals are interchangeable between angle and y - pattern valve bodies
更換部件的完整清單可以在前一頁找到。閥帽組件和密封在角形和y形閥體之間可以互換。 -
Top ( upper ) mounting type : unnecessary to unload valve from pipeline for maintenance but just by opening the bonnet for on - line maintenance
頂裝式:閥門維修時不需要從管道拆下,只要打開閥蓋即可進行在線維修。 -
Holding the memory stops in position, turn the ( clockwise ) down until it stops against the valve bonnet. the memory has now been set
將記憶止動裝置保持在其位置上,順時針旋轉鎖軸環直到其停止靠到閥門閥蓋為止。記憶現在已經設置完畢。 -
Air cylinder valve bonnet
氣筒閥帽罩 -
To clean : inspect or replace worn valve disc, disconnect control pipe and unscrew bonnet from valve body using blunt tool and hammer on bonnet lugs
清洗:檢查或更換磨損的閥門閥瓣,斷開控制管道,用鈍工具和錘打閥蓋塞頂部,從閥體上旋下閥蓋。 -
Bonnet nuts : number is dependent on valve size and class
閥蓋螺母:閥門通徑和壓力等級不同,螺母的數量也有所不同。 -
Install the valve bonnet. torque to 70 ft. / lbs
安裝閥蓋。扭矩為70英尺/磅。 -
Tightening valve bonnet is necessary to stop any leaks
如果必要緊固閥蓋,避免任何泄漏。 -
Tag location for gate and globe valves is typically on the valve yoke or body / bonnet flange
閘閥和截止閥的標簽位置通常在閥門軛架或閥體/閥蓋法蘭上。 -
Replace memory stop / lockcollar assembly into the valve bonnet
將記憶止動/鎖軸套總成重新放置到閥蓋內。 -
The entire valve body and bonnet, inside and outside are fully coated with a fusion bonded epoxy that offers protection against corrosion and abrasion. the wedge is fully encapsulated with a vulcanized sbr or epdm rubber. all trims are made of stainless steel and copper alloy to prevent from polluting fluid medium
閥門內外表面採用無毒環氧樹脂粉末塗敷,閘板全包耐蝕橡膠,其他與介質接觸的零件,均採用不銹鋼和銅合金製造,具有良好的抗蝕性能,不污染介質。 -
Bonnet studs : number is dependent on valve size and class
閥蓋柱頭螺栓:閥門通徑和壓力等級不同,螺栓的數量也有所不同。 -
Unitized bonnet / base design, rugged construction and 2 - ring control make the 41a safety relief valve extremely dependable in terms of pop action, seat tightness and repeatability
採用閥蓋/基座結構,堅固耐用,雙環控制,這使得型號41a安全閥在彈起作用、閥座密封和重復性等方面特別穩定可靠。 -
Ratings ? valves must only be used in operating conditions within the appropriate ansi pressure - temperature ratings for valve class rating and body / bonnet material ( see technical data section )
額定壓力溫度等級?閥門只能用在規定閥門額定壓力等級和閥體/閥蓋材料的ansi壓力-溫度等級規定的應用環境中。 -
Ratings ? valves must only be used in design conditions within the appropriate ansi pressure - temperature ratings for valve class rating and body / bonnet material ( see technical data section )
額定壓力?所採用的閥門只能夠用在閥門所標注的針對閥門等級額定值和閥體/閥帽材料的ansi壓力-溫度額定值的設計條件范圍內(參閱技術參數章節) 。 -
Close the valve fully by turning the stem in a clockwise direction. tightening valve bonnet is necessary to stop any leaks
順時針旋轉閥桿,完全關閉閥門。如果必要,則緊固閥蓋以消除任何泄漏。 -
The valve bonnet may now be removed. there may be slight leakage as the backseat does not provide a drip - tight seal
現在可以拆卸閥蓋。如果後座無法提供無滴漏密封,則會有輕微的泄漏。 -
The valve bonnet may now be removed. there may be slight leakage, as the metal - to - metal backseating does not provide a drip - tight seal
現在可以拆卸閥門的閥蓋。當金屬-對-金屬後座無法提供無滴漏密封時,可能會有點泄漏。
分享友人