calculate the output value 中文意思是什麼

calculate the output value 解釋
計算產值
  • calculate : vt 1 計算，核算。2 預測，推測。3 〈多用被動語態〉計劃，籌劃；使充作；使適合 （for）。4 〈美口〉打...
  • the : 〈代表用法〉…那樣的東西，…那種東西。1 〈用單數普通名詞代表它的一類時（所謂代表的單數）〉 （a） 〈...
  • output : n. 1. 產量；生產，出產，產品。2. 【醫學】（糞便以外的）排泄物；排泄量。3. 【電學】發電力，輸出功率；供給量。4. 輸出信號。
  • value : n 1 價值；重要性；益處。2 估價，評價。3 價格，所值；交換力。4 （郵票的）面值。5 等值；值得花的代...
  1. After analyzing the switching characteristic of mosfet, the object function of optimizing curve of the output capacitance coss is confirmed according to the switching loss caused by output capacitance coss, then the optimized curve of the output capacitance coss is ascertained by applying zoutendijk to seek the optimized value with constraint ; the simulation of switching circuitry and dc - dc circuitry is tested at different frequency in pspice, then the least square method is adopted to fit simulation curves to calculate corresponding energy data

    在電子線路模擬軟體pspice中進行了mosfet開關電路以及典型dc dc轉換線路模擬測試，針對不同頻段的測試結果，採用最小二乘擬合法對模擬曲線進行擬合，計算出相應的能量數據，最後綜合模擬結果確定出減小器件開關損耗，提高dc0c轉換線路效率的器件輸出電容cob優化曲線。
  2. If an input is given, the model can calculate the output. the worker can consult the numerical value to adjust and control the cement producing process

    建立的模型具有一定的實用價值，工人可參照模型計算出的監控數值現場調控水泥窯生產過程。
  3. Adopt the mean of analyzing the factors which influence the output of the crops to quantity and determine the factors, assess the correlation among the grading factors in the units and calculate the point value of these factors ; determine the weigh value of the factors. ten factors, which are content of organic matter, thickness of soil layer, quality of soil, pickled degree of land, condition of irrigation and state of shelter belt, the degree of land " s leveling, central focus region ( focus region location ), utilization method of soil, are chosen as grading index at last

    本文採用因素法定量化評價各地塊定級單元的相關性和權重性，最終選定了有機質含量、土層厚度、土壤質地、鹽堿化程度、排水能力、灌溉保證率、防護林完整度、條田平整度、中心區位，土地利用方式等因子作為定級的指標，使用了加權加和因素法進行了的定級計算，逐步完成了農用地質量情況的評價，劃分出了級別。
  4. The intelligent measuring meter configured by scm ( single chip microprocessor ) system is to sample and process the voltage signal output by the sensor, calculate and display the value of instant flow and total flow. furthermore, it can show the chargement according to the price of water set through the keyboard

    以單片機應用系統為核心的智能測量儀表負責對傳感器的電壓輸出信號進行採集和處理，計算和顯示出被測水流的瞬時流量和累積流量，並可根據所設定的單價實現水費的自動計價。
  5. In the course of design, we fully consider the actual conditions on the railway and take a series of corresponding measures to the concrete problem. such as we select high - accuracy microconvertor and have the converted function in succession data collecting system chip aduc812, design v / f circuit and external a / d circuit. in anti - interference of the hardware, we try to disperse each function module to avoid interfering each other, adopt photoelectric isolated technology to dispel the circuit connection of input and output. in controlling we import arithmetic mean into strain wave algorithm and real computing technology of virtual value for sample treatment of data, that is using the software to smooth away interfere error and to calculate actual value, thus it makes the precision of the data improve greatly

    在設計過程中，根據系統要求，充分考慮鐵路上的實際情況，針對具體問題採取了一系列的相應措施，如在器件選擇方面選用高精度microconvertor系列、具有adcdma連續轉換功能的數據採集微控制器晶元aduc812 ，設計了v f變換電路和外部a d轉換電路；在硬體抗干擾方面，將每個功能模塊盡量分散獨立開來以避免相互干擾、採用光電隔離技術消除輸入輸出通道上的電路聯系；在控制方面對于采樣數據的處理引入了算術平均值濾波演算法和真有效值的計算方法，即通過使用軟體來濾除系統中有干擾造成的誤差並計算真值，從而使數據的準確性得到極大地提高。
  6. ( 5 ) statistically analyze data : except provide basic analysis, it can also calculate the maximum, minimum, average and root - mean - square value of age, pre - hospital, bp, gcs, rts, iss, gos, ps _ triss, ps _ ascot. the results can be output or printed out by the forms of graph or report

    （ 5 ）數據的統計分析：本系統提供基本的數據統計分析功能，可進行包括年齡、院前時間、血壓、 gcs 、 rts 、 iss 、 gos 、 ps _ triss 、 ps _ ascot等資料的最大值、最小值、平均值、標準差等大量統計工作；統計結果可用圖形或報表形式導出或列印。
  7. Then, this discourse detailedly discusses system ' s developing method and process with object arx - developing tool of autocad and microsoft visual c + +, and discusses how to extract the geometrical information and how to calculate the coordinate value of screw thread holes " axes, and discusses the calculation of rotated angles and output of cut location file, also discusses how to make use of present research result about optimization of the machining process to program

    接著詳細論述了運用autocad的二次開發工具objectarx和微軟公司的visualc + +進行系統開發的方法和過程，討論了如何提取圖形信息和螺紋孔軸線坐標軸的計算，再到旋轉角度的計算和刀位文件的輸出，以及如何利用已有的加工工藝優化的研究結果進行編程等問題。
分享友人
分享到 Line

分享到臉書