carrier injection 中文意思是什麼

carrier injection 解釋
載流子注入
  • carrier : n 1 運送人，搬夫；負荷者；使役，〈美國〉信差，郵遞員；送報人；〈英國〉運輸行，運輸業者。2 傳書鴿...
  • injection : n. 1. 注射。2. 注射劑，注射液，針藥，灌腸（藥）。3. 充滿，注滿。4. 【醫學】充血。5. 【機械工程】噴射。6. 【宇宙空間技術】（衛星等的）入軌，射入軌道，射入軌道的時間[地點]。
  1. Testing of materials for semiconductor technology - measurement of carrier lifetime in silicon single crystals - recombination carrier lifetime at low injection by photoconductivity method

    半導體工藝材料的試驗.硅單晶中載流子壽命的測量.用
  2. During the " 10th 5 - year - project ", researches on the following techniques, new isotopic carrier, 5 parameters combination logging, oxygen activation logging, injection profile logging for polymer flooding, trace relative flow rate logging, and so on, have been carried out and some advanced and practical results have been obtained

    「十五」期間開展了新型同位素載體、五參數組合測井技術、氧活化測井技術、聚驅注入剖面測井技術、示蹤相關流量測井技術等課題的攻關，取得了一批先進實用的技術成果。
  3. Compound fluorouracil injection is a chemotherapy drug with various characteristics of carrier, targeting and increase immunity. the targeting system is able to directly deliver the liposome - coated drug to the lesion then kill cancer cells without side effects

    微脂體針劑是一種具有載體、靶向和提升免疫力等多功能的化學療法用藥，此靶向特性能直接將包覆化療藥物的微脂體針對病灶直接殺死癌細胞而不傷害正常細胞，再者，它也會增加身體免疫力並且無副作用。
  4. Account for the high electrical field induced from the high applied voltage relative to small dimension device, the mechanism of hot - carrier generation is analysed, the si - h bond broken model for hot - carrier injection and interface states generation is deduced and the substrate current model is developed

    基於mosfet偏壓不能按比例縮小所導致的高電場，對mosfet的熱載流子產生機理進行了分析，導出了熱載流子注入所引起的界面態的si - h健斷裂模型，並建立了表徵器件熱載流子效應的襯底電流模型。
  5. Since polymer light - emitting diodes ( pleds ) were invented, much efforts have been made to improve the brightness and efficiency of its electroluminescence for realizing pled commercial application. we investigated several factors influencing the brightness, efficiency and spectrum characteristics of pleds el, especially focused our attention on the processes of carrier injection, transport, recombination and annihilation factors influencing brightness efficiency of organic electroluminescence ( oel ) in doped single and double - layer pleds

    本文以提高聚合物器件的效率和亮度為目標，提出了提高及b幾種方案，研究了材料性質，器件結構，它們的穩態及瞬態特性及發光機理，特別關注了以兼具電子空穴傳輸能力的分子及摻雜聚合物作成的單雙層摻雜聚合物發光器件中的載流子注入、遷移、復合及湮滅等。
  6. Finally, the mutual spreading between the sample zone and the carrier solution in flow injection analysis ( fia ), would always result in the sample zone ' s widening and reducing the sensitivity

    最後，流動注射分析中載流溶液與樣品的相互擴散會導致樣品區變寬而降低靈敏度。用空氣作載流就沒有擴散，靈敏度極高。
  7. The emphasis is about the metal line reliability, contact reliability, gate oxide integrity, and hot carrier injection in test. based on the test datum, the reliability of 1. 0 m process on single failure mechanisms is evaluated, and all the test structures are explained

    測試內容上著重介紹了金屬化完整性測試、氧化層完整性測試、連接完整性測試和熱載流子注入測試，根據測試數據，對1 . 0 m工藝線單一失效機理的可靠性進行了評價，對不同測試結構的作用進行了說明。
  8. Tddb and hce always take place simultaneously under device operation conditions. hot - carrier enhanced tddb effect of ultra - thin gate oxide is investigated by using substrate hot - carrier injection technique

    在通常的工作條件下，氧化層的經時擊穿和熱載流子效應總是同時存在的。
  9. Applying dh can enhance the injection ratio, strengthen the confinement to the carrier and enhanced the efficiency of the recombination. this make the brightness greatly enhance

    Dh結構不僅提高了載流子注入比並且加強了載流子限製作用，提高了輻射復合的效率，使得hb - led的亮度大幅度提高。
  10. The separated phase of blends and carrier injection, transport and decay were firstly investigated by monitoring two different transient el peaks

    首次引入監測基質和雜質兩個瞬態電致峰值來研究低摻雜體系的相分離及載流子注入、遷移和湮滅過程。
  11. Finally, the mutual spreading between the sample zone and the carrier solution in flow injection analysis ( fia ) would always result in the sample zone ' s widening and reducing the sensitivity ( obviously, the case in which the carrier solution was the reaction reagents was not included )

    該傳感器晶元保存於冰箱（ 4oc ） 10天後無明顯變化，且能連續重復使用200次而無明顯變化（測定值rsd小於5 ） ，該傳感器晶元成功用於血清中尿酸含量的測定，結果令人滿意。
  12. Carrier aggregation on the interface between organic layer and electrodes may screen extra electric field and reduce barrier height for carrier injection. ( 3 ) we utilized oxd as buffer layer in anode and lif in cathode in single layer mehppv pleds. and the efficiency and brightness was doubled. the results implied that aggregation of minority carriers at the interface may the role of blocking layer

    （ 3 ）在單層mehppv器件的陽極引入oxd作為電子阻擋修飾層， lif作為陰極修飾層，利用阻擋少數載流子實現界面電荷積累的方法提高了器件發光亮度和效率，分析了器件電流電壓特性，使器件發光效率和亮度提高了一倍以上。
  13. Magnetic - field - dependent carrier injection at la2 3 sr1 3 mno3 and organic semiconductors interfaces

    半金屬材料的臨界指數及臨界特徵
分享友人
分享到 Line

分享到臉書