casting bath 中文意思是什麼
casting bath
解釋
鑄條浴-
Research on the influence of the depth of slag pool on the depth of metallic bath using fem in the process of electroslag casting
電渣熔鑄中渣池深度對金屬熔池深度影響的有限元模擬 -
The optimized process parameters are : the concentration of casting solution is higher than 9wt %, casting speed is 0 73m / min, temperature of wash bath is 45 and post - treatment is used
當鑄膜液濃度在9wt以上，刮膜速度為0 . 73m min ，水洗浴溫度為45 ，並增加熱處理和塑化處理時，膜的分離性能較好。 -
With a decreasing cellulose concentration of casting solution or an increasing temperature of coagulation bath, the mean pore ssze becomes larger, resulting in higher pure water flux and lower rejection of bsa
隨著鑄膜液濃度的降低或凝固浴（純水）溫度的升高，膜的水通量有較大的提高，但截留率會明顯下降。 -
The coupled turbulent flow field and temperature field are simulated by finite element method ; the influence of casting speed on the turbulent flow field and temperature field in the melting bath and the interaction between those two field are analyzed ; the variation tendency of the heat flux intensity between the melting bath and casting roll and law of variation with changes of casting speed in the process of solidification are given ; a comparison between the simulation results and experimental results demonstrates their good agreement ; and the mechanism of the heat flux variation is identified by analysis on the temporature gradient and development of solidification within the melting bath and its influence on the variation of the heat flux intensity
採用有限元法模擬了雙輥鑄軋不銹鋼過程的流熱耦合問題;分析了鑄軋速度對熔池內流場、溫度場的影響以及流場與溫度場之間的相互影響;給出了凝固過程中熔池與鑄軋輥之間的熱流密度變化趨勢及隨鑄軋速度的變化規律，並把此模擬的結果與試驗的結果相比較，吻合較好;通過熔池內溫度場及溫度梯度分析了熔池內凝固的發展及其對熱流密度變化的影響。 -
The results indicate the even blended, clear suspensions owned a good stability and flowability, and can used as casting membrane solutions. both the stability of active carbon power suspensions and the integration properties of membrane being made from them were bad. coagulant bath temperature had a strong influence on pu, pes composite flat membrane
結果表明，經過充分分散的sio _ 2填充聚合物鑄膜液，均勻透明，具有較好的穩定性和流動性，適于用作平板膜和中空纖維膜的原料液；而活性炭粉填充聚合物鑄膜液穩定性較差，所得膜的綜合性能也差於sio _ 2填充膜。 -
By using atomic force microscopy ( afm ) investigation on the membrane surface, different separation properties can be explained very well according to the data of pore size. increasing temperature or nmmo concentration of coagulation bath or decreasing concentration of casting solution leads to larger skin pore size, wider pore size distribution and higher values of the roughness parameters
用原子力顯微鏡（ afm ）對膜表面形態的分析表明：膜表面孔徑隨著鑄膜液濃度的降低、凝固浴溫度和濃度的升高而逐漸變大，且孔徑分佈變寬。 -
With an increase of nmmo concentration of coagulation bath or concentration of casting solution, the crystallinity of membrane increases. however, an increase of temperature of coagulation bath is accompanied by a decrease of crystallinity of membrane
膜的結晶度隨鑄膜液濃度、凝固浴濃度、刮膜速度的增加而增大，隨凝固浴溫度的升高而降低。
分享友人