chamber gas temperature 中文意思是什麼

chamber gas temperature 解釋
燃燒室氣體溫度
  • chamber : n 1 〈古、詩〉室，房間；寢室，臥室；〈pl 〉套房；〈pl 〉律師[法官]辦公室。2 會議室，會場；議會，...
  • gas : n （pl gases ）1 氣，氣體，氣態 〈cf fluid; solid〉 2 可燃氣，煤氣，沼氣；【礦物】瓦斯。3 【軍事...
  • temperature : n. 1. 溫度，氣溫。2. 體溫。3. 〈口語〉發燒，高燒。
  1. But the temperature difference at the vertical direction in combustion chamber in lead column, that is said by operator, is over 60 ?. ( 2 ) according to the experiences in the practice, the second layer air and the second layer gas had a little effect of support burning, and the third air has little effect for combustion, and the power to drawing exhaust gas can only be adjusted in limited range. the problems, it is said above, restricted more advance of some kinds of technology and economy target in spelter refining in new jersey furnace

    由於鋅精餾爐產量提高，一些問題開始暴露出來： （ 1 ）燃燒室?舶要求溫度差不超過10 ，而從現場反映的情況來看，燃燒室上、中、下部溫度差已超過60 ； （ 2 ）在生產實踐中，發現燃燒室第二層空氣、第二層煤氣作用甚小，第三層空氣失去助燃作用，廢氣出口的抽力可調范圍有限；以上這些問題在客觀上制約了精餾塔在鋅精煉中各項技術經濟指標的進一步提高。
  2. It is found that the appropriate lowering of the chamber temperature of water gas producer and the thickness of coal bed is favorable to controlling the volume fraction of o2 and co in the recovered flue gas

    通過試驗與分析，發現適當降低水煤氣發生爐爐溫與煤層厚度，有利於控制回收煙氣中o2及co的體積分數。
  3. As to the simulation, three - dimensional n - s equations and two - phase flow model, in which the liquid toluene spray as discrete particles was considered, were employed to describe the turbulent combustion processes in the combustion chamber. the mass and energy transfer between the two phases were calculated by the droplet evaporation model, and the arrehnius model was used to obtain the gas chemical reaction rate. the details of 3d flow field, the distributions of temperature and compounds were obtained by solving the equations

    數值模擬方面，應用三維湍流n - s方程以及顆粒軌道模型描述了激光器燃燒室內部的噴霧兩相燃燒流動過程，兩相之間的質量、能量交換由液滴蒸發模型計算，氣相化學反應速率由arrhnius公式計算，通過耦合求解氣液兩相模型方程，模擬了燃燒室三維流場，得到了燃燒室內的溫度和組分濃度分佈。
  4. For the sake of realizing compressive ignition of single fueled natural gas and aiming at the characteristics of high spontaneous combustion temperature of natural gas, the separated combustion chamber provided with low heat radiation structure was designed, meanwhile the heating device for the intake pipe air and the ceramic electro - thermal plug heating device inside the separation chamber were set up

    摘要為實現單一燃料天然氣的壓燃著火，針對天然氣自燃溫度高的特點，設計了具有低散熱結構的分隔式燃燒室，同時設置了進氣管空氣加熱裝置和分隔室內陶瓷電熱塞加熱裝置。
  5. The combustor do n ' t fail if transient rise of temperature field is neglected, the stress field of combustor can n ' t cause gas film wall rupture. 2. combustor ' s creep and relaxation is calculated in steady temperature field, the results show that creep and relaxation is not main reason destroying combustor chamber

    對穩態溫度場下的蠕變鬆弛計算表明，高溫下的蠕變鬆弛促使火焰筒的熱應力下降，在所考慮的條件下穩態溫度場導致火焰筒的蠕變變形不是火焰筒破壞的主要原因。
  6. In order to solve the problems effectively, under the auspices of 863 plan in china, the synthesis diagnosis has been carried by means of measuring and numerical imitating the combustion chamber of refining column, and some conclusions is such as : ( 1 ) through measuring the temperature and combustion in the burning chamber of the refining column, the result shows the temperature difference on the same level is more than that in height direction, and there is a few of co in bottom of burning chamber. ( 2 ) in order to ensure normal work of flue system in lead column in the course of zinc refining, theoretic calculation and measure about the flow resistance of exhaust gas are carried through. the results of study reveal that drawing out force of chimney is inadequate, which is mainly caused by illogicality of flue construction

    在研究過程中，採取了現場實測和數值模擬手段對韶關冶煉廠鋅精餾鉛塔燃燒室及排煙系統進行了綜合診斷，具體結果包括如下： （ 1 ）完成鋅精餾鉛塔燃燒室內溫度測試以及燃燒狀況的測試，結果發現：鉛塔燃燒室內水平方向的煙氣溫度並非均勻，而且其溫差比上下方向的溫差更大，以及鉛塔燃燒室尾部存在co未燃燼問題； （ 2 ）為了保證鉛塔煙氣系統的正常工作，對煙道系統的阻力進行了理論計算及測試分析，結果發現：鋅精餾鉛塔煙氣系統中煙囪抽力不夠，這主要是煙道結構不合理所造成的。
  7. Great difference in pressure for two flow made pressure wave system and it help to extend the delay time for gas in chamber, which increases combustion effusion. second, to increase combustion effusion, the inlet temperature of air and gas should be enhanced in the range of heat releasing in chemical reaction. third, the first work condition is unburned absolutely and the second work condition is burnt in shear layer of inlet and the end of down wall zone in straight segment

    對于壓力差很大的兩股氣流，所形成的壓縮波系的結構可以增加燃氣駐留時間，提高燃燒穩定性;為了提高擴散燃燒的效率，在保證能放熱的化學反應溫度范圍之內，應適當提高燃氣及空氣的來流入口溫度;燃氣噴嘴應居於燃燒室軸線上，是改進超音速燃燒室結構的一種思路。
  8. Abstract : the causes for low efficiency of the heater in no. 2 crude unit of jpc refinery are described and analyzed including water leaking of steam soot blower, dew point corrosion caused by steam, soot deposits in convection chamber owning to poor soot blowing, high flue gas temperature, no heat recovery of flue gas, and poor performance of insulation lining, etc. by using sonic soot removing system, flue gas recovery system, spray coating of fiber and rock wool, as well as adjustment of flow scheme accordingly in the technical revamping. the dew point corrosion is completely eliminated, the insulation performance is improved, the heat loss is reduced by 1. 25 %, the flue gas temperature is reduced to about 170, and the heater efficiency is increased from 83 % to more than 90 %

    文摘:分析了金陵石油化工公司煉油廠二套常減壓裝置加熱爐存在的因蒸汽吹灰器漏水，蒸汽引起露點腐蝕及吹灰效果差造成對流室積灰，排煙溫度高，煙氣熱量未回收利用以及爐子保溫襯里效果差等問題，提出採用聲波除灰系統、煙氣回收系統、纖維噴塗和巖棉噴塗及相應的流程調整等改造措施.測定結果表明，本次技術改造解決了因蒸汽吹灰器漏水所造成的露點腐蝕問題，提高了保溫效果，減少散熱損失1 . 25 % ，排煙溫度降至170左右，裝置的爐效率由83 %左右提高到90 %以上
  9. The causes for low efficiency of the heater in no. 2 crude unit of jpc refinery are described and analyzed including water leaking of steam soot blower, dew point corrosion caused by steam, soot deposits in convection chamber owning to poor soot blowing, high flue gas temperature, no heat recovery of flue gas, and poor performance of insulation lining, etc. by using sonic soot removing system, flue gas recovery system, spray coating of fiber and rock wool, as well as adjustment of flow scheme accordingly in the technical revamping. the dew point corrosion is completely eliminated, the insulation performance is improved, the heat loss is reduced by 1. 25 %, the flue gas temperature is reduced to about 170, and the heater efficiency is increased from 83 % to more than 90 %

    分析了金陵石油化工公司煉油廠二套常減壓裝置加熱爐存在的因蒸汽吹灰器漏水，蒸汽引起露點腐蝕及吹灰效果差造成對流室積灰，排煙溫度高，煙氣熱量未回收利用以及爐子保溫襯里效果差等問題，提出採用聲波除灰系統、煙氣回收系統、纖維噴塗和巖棉噴塗及相應的流程調整等改造措施.測定結果表明，本次技術改造解決了因蒸汽吹灰器漏水所造成的露點腐蝕問題，提高了保溫效果，減少散熱損失1 . 25 % ，排煙溫度降至170左右，裝置的爐效率由83 %左右提高到90 %以上
  10. Abstract : by using the 3 - d unsteady state heat transfer equation, the heat convection and radiation between the checker and the gas which flows through the checker holes, and the heat conduction among the checker in the chamber of the hot blast stove were studied. the time dependable gas temperature and the temperature distributions within the checker were obtained

    文摘:應用三維非穩態熱量傳輸方程，對高爐熱風爐在燃燒過程中蓄熱室內格子磚與氣體之間的對流和輻射傳熱，以及格子磚內部的導熱過程進行了耦合求解.得到了在燃燒期內格子磚及燃燒過程中燃燒廢氣的溫度分佈情況及其隨時間的變化規律
  11. The passage dimension of separation chamber, the heating temperature of intake pipe air and the relevant influence of the ceramic heat insulation coating of combustion chamber upon the compressive ignition process of natural gas were studied by experiment

    實驗研究了分隔室通道尺寸、進氣管空氣加熱溫度、燃燒室陶瓷隔熱塗層對天然氣壓燃著火過程的相關影響。
  12. The influence of the array chamber, carrier gas flux and sample temperature on the performance of the system was discussed in the identification of different brands of cigarettes. while in the detection of alcohol with gasoline interference, the methods of signal preprocessing showed great effects. and at the end, suggestions were made on the optimization of the system construction and measurement strategies, which advanced towards portable en systems

    在卷煙鑒別問題中詳細研究了測試氣室、載氣流量、樣本溫度等實驗條件對系統的識別性能的影響；在有汽油干擾的酒精檢測問題中，考察了數據預處理方法對于識別結果的影響，並提出了系統改進的建議。
  13. The temperature - control accuracy of gas chromatograph, mode of entry of liquor samples from vaporizing chamber after vaporization to chromatographic column, dnp chromatographic column efficiency, and liquor analysis time length etc. are the factors influencing the accuracy of the data in the analysis of liquor microconstituents by gas chromatograph

    氣相色譜儀器的控溫精度、酒樣進入汽化室汽化后進入色譜柱的方式、 dnp色譜柱效、酒樣分析時間的長短等都是影響氣相色譜儀分析白酒中微量成分數據準確性的重要因素。
  14. The unstable gas stream is characterized by oscillations with transient velocities of about + 100 m / s and frequencies from 50 - 200h /. the enhanced mixing and transport processes lead to a highly efficient moisture evaporation rate during pulsating spray drying. the computational fluid dynamics ( cfd ) method was used for the analysis and investigation of flow, temperature and humidity fields in a pulsating flow spray - drying chamber

    長期以來，對噴霧乾燥過程進行了各種試驗和模擬研究，但這些研究並不能揭示噴霧乾燥室內氣體運動狀態，顆粒群的運動軌跡和各種熱力學參數分佈信息，常規的測試手段又很難測得，而這些參數分佈信息對乾燥器沒計和過程優化具有重要指導作用。
  15. The simulations results show that the average combustion temperature is much lower in fuel - rich state and little higher in oxygen - rich state near the best o / f ratio. by extending the post - chamber length the oxidizing gas and the fuel pyrolytic gas can burn completely and the average combustion temperature can be prominently increased. the fuel - rich recirculation zone close to the head of combustion chamber is very important for the combustion

    計算結果分析表明：發動機在富燃狀態下平均燃燒溫度偏低，在接近理想配比的富氧狀態下平均燃燒溫度有所提高；加長補燃室可以大幅度提高發動機的平均燃燒溫度，並促進氧化劑氣體和熱解氣體的充分燃燒；燃燒室頭部的富燃迴流區對發動機的燃燒非常重要，去掉燃燒室頭部突擴段后，氧化劑氣體和燃料熱解氣體不能充分燃燒，發動機的平均燃燒溫度大幅下降。
  16. This paper probes into the emission of sulphur dioxide through the boiler chimney, concerning the option of coal of raw material, sulphur share in the chamber of a stove reaction mechanism, the temperature control of flue gas in the chamber of a stove and the operaton of dust remover

    摘要以常州中天焦化有限公司為例，從原料煤的選擇、煤中硫份在爐膛中的反應機理及爐膛煙氣溫度控制、除塵器的運行等方面討論了減少鍋爐煙囪二氧化硫排放問題。
  17. In this paper, a three - dimensional ( 3d ) program for the three - dimensional reactive flow fields of complicated geometric nozzle, which governed by the compressible full navier - stokes equations with realizable k - s turbulent model, has been upbuilt by using full implicit couple arithmetic and fvm ( finite volume method ) based on understanding and assimilation of a two - dimensional program group of cr ( chamber - radon ). the new program fulfils the urgent need of numerical tools for simulating three - dimensional reactive flow - fields of hylte ( hypersonic low temperature ) and other latest nozzles, for which cr is out of action in simulation, and can be applied to simulate other chemical laser system, such as chemical oxygen iodine laser ( coil ), overtone fluoride hydrogen, all - gas iodine laser, and so on. furthermore, some related topics about nozzles design and engineer ing also have been discussed

    本文在二維cr （ chamber ? radon ）程序研究的基礎上，採用有限體積方法和完全隱式的耦合演算法，通過求解帶realizablek -兩方程湍流模型的多組分、有反應的三維完全納維埃?斯托克斯（ n ? s ）控制方程，建立了一套能夠對復雜形狀的三維噴管和光腔進行數值模擬的三維程序，解決了連續波df hf化學激光器增益發生器設計缺乏三維數值模擬工具的問題，並用該工具解決了cr程序無法實現的hylte等復雜三維噴管流場的理論模擬問題。
  18. The best process for high quality tio _ ( 2 ) thin film deposited on k9 glass by reb is studied by using orthogonal test method, the se results indicate that the best process for tio _ ( 2 ) thin film deposition is the substrate temperature of 300, the total gas press in the chamber of 2 x 10 ~ 2pa and the deposition rate of 0. 2 nm - s - 1, of which the substrate temperature has influence on the optical properties of the deposited films notably

    文中首先以tio _ 2薄膜的折射率和消光系數為研究對象，採用l9正交試驗法研究了在k9玻璃上制備高光學質量tio _ 2薄膜的最佳工藝條件。橢圓偏振儀的測試結果表明，制備tio _ 2薄膜的最佳工藝條件為：基片溫度300 ，工作真空2 10 ~ （ - 2 ） pa ，沉積速率0 . 2nm ? s ~ （ - 1 ） ，其中基片溫度對薄膜光學常數的影響最大，該結果具有較好的可重現性。
分享友人
分享到 Line

分享到臉書