check screw 中文意思是什麼

check screw 解釋
保險螺釘
  • check : n 1 （象棋）將軍（ ），被將軍的局面。2 （突然的）妨礙[制止，阻止]；停頓，挫折；【打獵】（獵狗聞不...
  • screw : n 1 螺旋；螺釘。2 螺旋槳；暗輪。3 暗輪輪船。4 螺旋狀物。5 拔塞器；螺絲鉆子。6 螺旋的一擰；螺旋的...
  1. Shipbuilding - bronze 5k screw - down check globe valves

    造船.青銅制5k螺旋擰緊止回球閥
  2. Shipbuilding - bronze 16k screw - down check globe valves

    造船.青銅制16k螺旋擰緊止回球閥
  3. Shipbuilding - cast iron 5k screw - down check globe valves

    造船.鑄鐵制5k螺旋擰緊止回球閥
  4. Low pressure bronze male screw - thread check valve for marine use

    船用低壓外螺紋青銅止回閥
  5. Low bressure bronze male screw - thread check valve for marine use

    船用低壓外螺紋青銅止回閥
  6. Equipped with electronic controller fini tronic and preset for remote control for two or more compressors. it offers working pressure and oil mist separator tank inner pressure indication, separator filter clogging lashing alarm before overpressure e - stop, electric motor temperature control, maximum screw assembly temperature control, air temperature on pressure end indication, electric motor direction of rotation check, time to scheduled maintenance term, total operating hours and operating hours under load, alarm log of last five failure events

    並預設為丙臺以上空壓機聯機遠程控制，有工作壓力和油氣分離器罐內壓指示，分離器過濾器阻塞報警，電機溫控，螺桿總成溫控，壓力端空氣溫度指示，電機轉向檢查，維護周期油，油過濾器，空氣過濾器，分離器過濾器，總運行時間和負載運行時間，記錄上五個報警故障等。
  7. It offers working pressure and oil mist separator tank inner pressure indication, separator filter clogging flashing alarm before overpressure e - stop, electric motor temperature control, maximum screw assembly temperature control, air temperature on pressure and indication, electric motor direction of rotation check, time to scheduled maintenance term, total operating hours and operating hours under load, alarm log of last five failure events

    並預設為丙臺以上空壓機聯機遠程控制可檢測包括操作壓力油氣分離器罐內壓，電機溫度和轉向，螺桿總成溫度過濾器堵塞報警等參數，並可顯示總運行時間和負載運行時間。
  8. Abstract : this article discussed the causes of errors in nc program of machining screw using non - instant center envelope method. an analytical method to check the accuracy of nc program has been given, thus the theory basis of improving nc program has been provided in this article

    文摘:對目前常用的無瞬心包絡法螺桿加工數控程序中產生誤差的原因進行了分析研究，提出了一種校驗數控程序精度的分析方法，為改進數控程序提供了理論依據。
  9. Check the screw holes of two flanges in the pipeline for alignment with reserved clearance

    檢查管路兩法蘭的螺絲孔的是否有對正及預留的間隙。
  10. Shipbuilding - bronze 5k screw - down check angle valves

    造船.青銅制5k螺旋擰緊止回角閥
  11. Shipbuilding - bronze 16k screw - down check angle valves

    造船.青銅制16k螺旋擰緊止回角閥
  12. Shipbuilding - cast iron 5k screw - down check angle valves

    造船.鑄鐵制5k螺旋擰緊止回角閥
  13. Shipbuilding - cast iron 16k screw - down check angle valves

    造船.鑄鐵制16k螺旋擰緊止回角閥
  14. Shipbuilding - cast iron 10k screw - down check angle valves

    造船.鑄鐵制10k螺旋擰緊止回角閥
  15. Hang door sheet to adjust every level the screw in lifting wheel is adjustable. check the lock and push the door to make sure it is slippery

    掛門鈺調整各門鈺的水平吊輪上有螺絲可調節，檢查鎖具能否鎖上，趟動門鈺感覺是否順滑。
  16. Shipbuilding. sea water valves. screw - down stop - and - check valves. pattern iii. operating mechanism. parts list

    造船工業.海水專用閥門.螺桿向下止動和止回閥.式樣ii .操作機構零件細目表
  17. Shipbuilding. sea water valves. screw - down stop - and - check valves with opening mechanism. pattern iv. operating mechanism parts list

    造船工業.海水專用閥門.帶打開機構的螺桿向下止動和止回閥.式樣.操作機構零件細目表
  18. Shipbuilding - cast iron 10k screw - down check globe valves

    造船.鑄鐵制10k螺旋擰緊止回球閥
  19. Shipbuilding - cast iron 16k screw - down check globe valves

    造船.鑄鐵制16k螺旋擰緊止回球閥
  20. Shipbuilding - cast steel 10k screw - down check globe valves

    造船.鑄鋼制10k螺旋擰緊止回球閥
分享友人
分享到 Line

分享到臉書