clamping circuit 中文意思是什麼
clamping circuit
解釋
鉗位電路-
Through instance and analyzing concrete data, the two ways of measuring insulation are introduced. the implementation of the method of clamping rundle circuit and its capability are described emphatically
通過對實例和具體數據的分析，介紹了2種測量絕緣的方法，重點講述了鉗位電路梯級測量法的實現及其性能 -
In regard to product technology, we have imported the eo rigid pipe ferrule technology and no - skive hose clamping technology so as to ensure the technical requirements of reliability and no leakage for the fluid circuit
在產品技術上我們引進eo硬管卡套技術和無需剝膠的軟管扣壓技術，確保液壓系統管路的可靠性、無泄漏的技術要求。 -
The analysis of ppf ’ s operation principle is introduced in detail in this paper. further more, the effect on the circuit operation is also analysed, which caused by clamping capacitance and different transformer leakage inductance value
本文首先深入研究了推挽正激變換器的工作原理，分析了穩態條件下的工作模態，同時分析了箝位電容與變壓器原邊漏感的大小對于工作模態的影響。 -
Bidirectional clamping circuit
雙向箝位電路 -
Baker clamping circuit
貝克箝位電路 -
The following is the main works and conclusions of this thesis. the novel upfc needs high power rate because it is generally used in high voltage transmission lines. after studied high - power converters and the literatures of upfc, the main circuit topology of novel upfc base on diode - clamping multilevel inverter is presented and the principle of using novel upfc to eliminate zero sequence and negative sequence currents is analyzed
本文所做的主要工作及得出的主要結論如下：由於upfc一般用於高壓輸電線，其功率等級要求很高，在綜合研究大功率變換器和upfc現有文獻的基礎上，提出了基於二極體箝位多電平變換器的新型upfc的主電路拓撲，分析了用其來濾出高壓輸電線非全相運行時所產生的零序和負序電流的原理。 -
The main ideas of the thesis and the contributions to the resonant dc - link area are also listed in this chapter. a novel control strategy for the two - amplitude actively clamped resonant dc - link is proposed in chapter ii. it neglects the bus short circuit time adjuster and stabilizes the clamping voltage by a pi regulator so that the obtained link frequency is improved and the link losses are greatly reduced
第二章針對雙幅控制技術在單相橋式電壓源逆變器中的應用為範例進行研究，提出了直流母線無短路控制和通過pi調節環穩定箝位電壓的雙幅諧振控制策略，進一步提高了母線振蕩頻率，減少了直流環節損耗。 -
Clamping diode circuit
鉗位二極體電路 -
Presents the simple but highly reliable on - line detection of ultrasonic transducer clamping capacitance based on the impedance circuit model constructed through the impedance characteristics of the ultrasonic transducer under triple harmonics, and concludes from experimental results that this method can be used to effectively detect the variation of clamping capacitance while the transducer is operating, and the matching inductance can be dynamically regulated according to the results of detection, and dynamic matching can therefore be achieved in the real sense at the end of the transducer to improve the overall performance of the whole system
為了解決大功率超聲應用的換能器電端匹配問題，分析了超聲波換能器在諧振頻率三次諧波下的阻抗特性，給出了超聲換能器三次諧波下的阻抗電路模型.並根據阻抗電路模型建立了對超聲換能器的夾持電容實現在線檢測簡單、可靠性高的方法，實驗證明該方法有效的.該方法可以在換能器工作過程中隨時檢測夾持電容的變化，根據檢測結果對匹配電感進行動態調整，實現真正意義上的換能器電端的動態匹配，從而大大改善匹配質量，提高系統的工作性能 -
And methods of modification are proposed, which are mainly presented on clamping circuit and method of compensating for the errors of count results. thus the performance of system can get further improvement
在測試過程中，發現了現有實現技術的某些不足，並有針對性的提出了改進，主要體現在計時電路中的鉗位電路設計和脈寬補償思想，有利於進一步改善系統性能。
分享友人