close sampling 中文意思是什麼

close sampling 解釋
密集取樣
  • close : vt 1 關(窗等),閉(眼等);蓋(蓋子等);鎖閉,封閉,塞,隔絕。 ★對 door box drawer 等,口語較...
  • sampling : n. 1. 取樣(品),取標(本)〈指行動或程序〉。2. 樣品,標本。3. 剽竊拼湊歌曲。
  1. Resampling is that every image element in the screen gives off one ray according to the planned observing orientation. this ray penetrates 3d data sets, and to chooses k sampling dots of equidistance along with it, and does three linear insert values according to color and opacity values of eight data dots that mostly close to certain sampling dot, then evaluate the opacity value and color value of it

    重采樣,是從屏幕上的每一個象素根據設定的觀察方向發出一條射線,這條射線穿過三維數據場,沿著這條射線選擇k個等距的采樣點,並由距離某一采樣點最近的8個數據點的顏色值和不透明度值做三次線性插值,求出該采樣點的不透明度值及顏色值。
  2. When sampling period is very low or close to ideal case for signal detection in additive gaussian white noise ( agwn ), the detection circuit with matched filter is optimal

    摘要在加性高斯白噪聲信號檢測中,在采樣周期極小或接近理想的情況下,連有匹配濾波器的檢測電路是最佳的。
  3. In the simulation study, the parameters of dipoles were given, it would be considered whether it could be recovered correctly by dllm based on scalp potential sampling with a set of electrode array. it was also examined that how electrode number influenced the recovered quality of dipole parameters. the simulation showed that the number, position and strength of dipole set were greatly close to the original condition ; the shallower the dipoles were, the higher the precision of source localization was ; the optimal depth of dipole layer was greatly close to the ideal position ; the accuracy of source localization was increasing when more electrodes were used

    在模擬研究中,首先設定已知的偶極子數目及其所在的偶極面深度等參數,然後用一定數目的電極抽取正向計算獲得的頭皮電位,考察該模型在上述理想條件下,基於頭皮電位是否能正確獲取偶極子數目及其參數、以及電極數目對結果的影響。
  4. Before the development of the system, the article describes the above - mentioned aspects, as the bases of the system development. the article emphasizes related auto - controlling technologies : open - 100p and close - 100p, and control mode of negative - feedback, the scatter and quantization of the simulate signal, the conception of a / d and d / a conversion and code / encode, the basic sampling principles of the simulate signal. the article introduces the operation method and process of the system by means of the load spectrum

    文章對相關的理論進行了陳述,以作為系統開發的理論依據,重點闡述了自動控制系統中包括開環閉環在內的幾大主要控制模式,以及有關的負反饋控制方式,模擬信號的離散與量化,模數轉換、數模轉換、編碼譯碼的概念,及模擬信號采樣的基本原理? ?采樣定理,並以載荷譜法為例,簡述了所研究的系統將要採取的工作方式及工作過程。
  5. It ' s briefly demonstrated that the overall plan of the close range shortwave marine communication system, which including format of radio propagation, operation frequency, communication architecture, main parameters and the sampling part of receiver

    以水下作戰平臺對母艦的短波通信為背景,對海上近距短波通信系統的總體方案進行初步論證。其中包括電波傳播形式的論證、工作頻段的選擇、通信體制的選擇、接收機總體指標以及接收機采樣部分技術論證。
  6. Examples show that the results obtained using laplace method are very close to that obtained using gibbs sampling method

    實例表明通過laplace方法得到的估計與利用gibbs抽樣方法得到的參數的bayes估計很接近。
  7. This paper divides into six chapters : the first chapter - base on the analyses of the origin, conception and development status of sr, this chapter discusses the key technology and realize difficulties of sr and advances the intention and meaning of the paper. the second chaptei - the sr system with radio frequency band - pass sampling architecture is a design scheme close to software wireless radio ( swr ), this chapter introduces three system architecture of sr system and analyses the theory of radio frequency band - pass sampling. the third chapter - this chapter analyses and designs the dsp hardware platform with radio frequency band - pass sampling architecture

    本論文分為六章:第一章在分析軟體無線電的起源、概念、發展概況的基礎上,闡述了軟體無線電的關鍵技術及實現難點,提出了本論文研究的目的與意義;第二章射頻直接帶通采樣軟體無線電結構是接近理想化的軟體無線電設計方案,本章對軟體無線電系統的體系結構及射頻直接帶通采樣原理進行了分析;第三章分析並設計了射頻直接帶通采樣結構軟體軟體無線電系統的dsp硬體平臺;第四章研究了調制解調及信號調制樣式的識別演算法並給出了dsp實現,這是在dsp平臺上實現軟體無線電功能的一種常規方法;第五章分析了應用快速原型技術開發軟體無線電系統的必要性及可行性,完成了軟體無線電系統的matlab模擬及結合ti公司的tms320c6711dsk板的快速原型實現,這也是本論文提出的軟體無線電的一種新的研究方法。
  8. In the calculating example of model inversion, the proper sampling interval and ' trend - band ' method were selected and inversion errors of the linear density and axes depth of cylinder were close to 0. 25 % and 3. 8 %, respectively

    在模型反演算例中,選擇了適當的采樣間隔和「趨勢鑲邊」法,反演的圓柱體線密度和軸心深度誤差分別為0 . 25 %和3 . 8 % 。
分享友人