combination control system 中文意思是什麼

combination control system 解釋
綜合控制系統
  • combination : n 1 結合，合併，混合，聯合，配合，組合。2 合作；共謀，同謀；同黨。3 〈pl 〉〈英國〉連褲襯衣。4 【...
  • control : n 1 支配，管理，管制，統制，控制；監督。2 抑制（力）；壓制，節制，拘束；【農業】防治。3 檢查；核...
  • system : n 1 體系，系統；分類法；組織；設備，裝置。2 方式；方法；作業方法。3 制度；主義。4 次序，規律。5 ...
  1. Finally, the controller working based on the combination of rbf neural networks and traditional pid control was applied to in aclinic kinetic machinery and lifting machinery of tower crane. the simulation of this controller was made using matlab, and the simulation results showed that the control system has some merits, such as quick response, little overshoot, well anti - jamming capacity, and little steady - state error, etc. both the dynamic property and static characteristic of this controller are better than traditional pid controller, and meet the tower crane

    應用matlab對塔機的變幅和起升機構的運動控制進行模擬，模擬結果表明基於rbf神經網路整定pid的控制系統具有響應快、超調小及穩態誤差小等優點，其動、靜態性能優于單一pid控制，從而提高了塔式起重機工作機構的工作性能。
  2. Comparing and analyzing the synchronous control strategy, which brings up the new method to control the double un - symmetry jars proceed synchronously with the combination of proportional valve and servo valve, which forms closed loop control ; basing on the above methods, models are made to get mathematics models of position control system and to analyze system model theoretically by using pid controller, we can realize regulating parameters, minimizing synchronous errors and enhancing the dynamic performances ; the simulink tool box in matlab software is used to imitate the system according to the model, which not only makes the result visual and easy to adjust the parameters in interactive way but also lets us understand the effects of different parameters and optimizes the dynamic properties. the theory of plc control in dshp is discussed after advanced understanding of the system movements. hardware design and general regulation are given on the base of siemens company products s7 - 200 plc

    本文根據大量的國內外文獻，對研配液壓機的工作原理及設計結構進行了簡介；對位置同步的控制方法進行了比較分析，提出比例閥和伺服閥復合控制的閉環結構來對非對稱雙缸進行同步控制電液比例同步控制方案；在此基礎上著重對比例閥控非對稱缸建模，最後得到位置控制系統的總體數學模型，從理論上對同步系統動態特性進行了分析，並用pid控制器進行參數整定，減小雙缸同步誤差、提高系統的動態響應性能；其中控制性能的分析藉助于matlab軟體中的simulink工具箱，由已建立的數學模型形成模擬模型，得到可視化的模擬結果，從而利於交互方式下調整參數，了解不同的參數對系統的影響，優化同步系統的動態性能；在深入了解系統的動作特性后，對plc控制研配液壓機的原理進行了探討，針對siemens公司s7 ? 200型plc給出了硬體設計的總體規劃，編制出研配液壓機動作控製程序，在編程中著重研究位移傳感器與plc的通訊、雙缸同步運行的pid控制在plc上的實現及bcd碼撥盤輸入程序的植入問題。
  3. After target is detected the on - board avionics suite in combination with the automatic control system of the helicopter solve the task of bringing the helicopter to the designated point and automatic firing of the weapons selected by the pilot

    當捕獲目標后，機上的自動控制系統與電子系統將解算任務數據，引導直升機飛向敵潛艇水域，並在飛行員指令準許下自動發射武器進行攻擊。
  4. The combination of fuzzy control and pid control would achieve fine function. the result of simulation and experiment show that the reformed automatic control system can gain upon higher product quality, less power consumption, less fixing tune and expense, etc

    模糊控制器在線實時地調節pid調節器的參數，通過數字pid控制演算法與模糊控制演算法的結合，提高了系統的自適應能力和魯棒性，獲得了較好的控制穩定性。
  5. Secondly, by means of analyzing several familiar control system structures and information amalgamation hiberarchy of robot., the characteristic of a control system structure based on parallel behaviour combination is summarized. also, the analysis of the robot ' s basic behaviour and the design of the behaviour control hiberarchy are expatiated in detail

    其次，分析了幾種常見的機器人控制體系結構，結合對信息融合層次結構的分析，總結了一種基於并行行為組合的控制體系結構的特點，並詳細地闡述了機器人基本行為的分析和行為控制層次結構的設計。
  6. In order to improve dynamic performance of the control system in the assembly robot, according to acpmsm ( ac permanent magnet synchronous motor ) vector control model and the control idea about preview control, the paper presents a kind of control strategies that is composite of a primary pid ( proportion integral dif - ferenfial ) with a preview feed - forward compensation, its compensation is equivalent to linear combination of future adjacent difference, the simulation results show that it can not only improve the system tracking performance effectively, but also implement easily

    摘要為了提高裝配機器人控制系統的動態性能，依據交流永磁同步電機矢量控制模型，從預見控制的思想出發，提出了一種在原有pid基礎上外加預見前饋補償的控制方法，這種控制方法的前饋補償項取未來幾項目標值一階差值的線形組合，並模擬驗證了該控制方法對提高系統跟蹤性能的有效性和簡單可行性。
  7. The stock options system is a cheap promotion method, and its special function of benefit combination does limit the managers " short - ranged and nearsighted actions, which helps the formation of managers " self - supervision and self - control system

    股票期權制度是一種真正低成本的激勵方式，其特有的利益捆綁功能可以有效地抑制經營者行為的短期化，有助於形成經營者的自我監督和約束機制。
  8. This control system adopts creditable plc for real control ; it sends many simulating signals collected by old sand temperature of inlet, suction opening temperature of double disk, inner sand temperature of double disk, current of mainframe and current of fan ; meanwhile, the operation signal and switching value signal outputted by material movement transducer is inputted to switching value module of plc ; it gets evidence of water feeding after cpu account ; the operation result of cpu is outputted by switching value of plc to control unlock combination of coarse, middle and thin water feeding electromagnetically operated valve and then gets different water feeding quantity

    該控制系統採用高可靠性的plc可編程序控制器進行實時控制，傳感器所採集的入口舊砂溫度雙盤抽風口溫度雙盤內砂溫主電機電流及鼓風機電流等模擬量信號直接輸入plc的模擬量採集模塊，同時加砂設備運轉信號及加砂設備物料移動檢測傳感器發出的開關量信號輸入plc的開關量模塊，由cpu獲取經運算而得到加水計算依據， cpu運算結果直接由plc的開關量輸出控制粗中細加水電磁閥的開啟組合，而得到不同的加水量。
  9. Incorporation of kones mature escalator technology, advanced micro - computer control system, high strength truss structure, classical driving system, and completed safety devices, fully ensure our products safe, reliable, endurable and bring steady and comfortable riding. refine craftwork, fluent lines and elegant style form the combination of practical riding function and visual enjoyment. frequency conversion technology selected makes the escalator more energy - saving

    引進通力成熟的自動扶梯技術，採用先進的微機控制系統，高強度的桁架結構經典的驅動技術完善的保護裝置，使產品安全可靠耐用，乘坐平穩安靜舒適精緻的工藝流暢的線條優雅的造型，使產品兼有乘坐的實用功能與視覺的裝飾效果變頻驅動的選用，使產品省電節能，而室外型自動扶梯能經受各種氣候環境條件考驗。
  10. The research objective is to improve the control system performance through the combination of the advanced control strategy with the meaningful information mined from the history operation database. firstly, a new solution for the control performance enhancement is presented by the reference of the kdd technology. aiming at practical application, a novel boiler load control method, which combines the multiple model adaptive control strategy with the data mining technology, is put forward in this dissertation

    本文第一部分為熱工過程式控制制與數據信息採掘，研究的重點是通過先進控制策略的應用以及運行數據中發掘的有用信息，提高現有典型熱工過程式控制制系統的性能，內容包括：首次提出了借鑒數據信息採掘技術的思路和方法，用於完善現有的熱力系統優化控制方案；在此基礎上結合生產實際，提出了運用多模型自適應策略實施鍋爐負荷控制，並利用關聯規則的數據信息採掘方法，通過對燃料發熱量信息的在線診斷，優化控制器結構，同時實現鍋爐燃燒配風的自適應調整，提高負荷、燃燒控制系統性能。
  11. This thesis presents an effective way to design pid controller through a combination of adverse deduce and genetic algorithm. the relationship between pid parameter and the root of the characteristic equation of the closed loop control system has been found out directly

    本文直接找出pid參數與閉環控制系統的特徵方程的根之間的關系，只要使特徵方程的根在z平面的單位圓內任意取值，然後再求出相應的pid參數，則閉環控制系統必然是穩定的。
  12. This thesis belongs to the research of the third aspect, the conpound drive system is used 1 ; o regenerate the 1oss energy. the low oil consumption and low b1eeder of vehic : le are achieved by way of the orggnic combination of transmission. hydrau1ic pressure and automatic control system, and the compotald drive system works hamonious1y with engine to raise the motive capability effectively

    本論文即屬于再生制動能量的研究范圍，研究以汽車減速及制動能量回收再利用為目的的液壓復合驅動系統，通過復合驅動系統中的液壓、傳動、自動控制三部分的有機結合及與發動機協調工作實現車輛的低油耗、低排放、並有效地提高其動力性能，是現有汽車節能、環保技術所未實踐應用的領域。
  13. During the designing of the electricity control system, the thesis used the mode that made up of monitor system and control system, formatted a network that is combined by far concentrates control system and nearly control system. the monitor system chooses the functional monitoring software - the king monitor and the man - machine interface, which operated conveniently. and the control system chooses dependably programmable logic controller and advance profibus fieldbus to completely control the spot equipments. author hopes the thesis ' s researches can do a little for the development of the water power control technique, and the combination of the hydraulic technique and the advanced technique, author also hoping heartily the control technique of the our country develop quickly

    上位機選用功能強大的工控組態軟體? ?組態王和操作方便靈活的觸摸屏。下位機則採用可靠性高的可編程式控制制器和先進的profibus現場總線完成對現場設備的控制。作者希望通過該課題的研究，能夠對水電行業控制技術的發展，對液壓技術與當今先進技術更好的相結合，起到一定的促進作用，也衷心地希望我國的控制技術取得飛速的發展。
  14. To remedy the disadvantages of conventional pneumatic servo system, pneumatic - hydraulic - combination - control ( phcc ) servo system is put forward, where the liquid medium is led into the conventional pneumatic servo system and controlled in closed - loop simultaneously

    摘要為從根本上克服常規氣壓伺服系統的缺點，將液體介質引入到氣壓伺服系統中，並對氣、液進行閉環控制，從而構成了一種氣、液復合介質控制系統氣液聯控伺服系統。
  15. Aiming at the essential defect of pneumatic medium, pneumatic hydraulic combination control ( phcc ) servo system is formed, in which the liquid medium with low compressibility and high viscosity is introduced into a normal pneumatic servo system and is closed - looped controlled simultaneously

    氣液聯控伺服系統正是基於克服或者補償氣體介質的根本缺點，將可壓縮性小、粘度較大的液體介質引入到常規氣壓伺服系統中，並進行控制而構成的一種新型的氣、液介質復合控制系統。
  16. Third, after the analysis of the disadvantage of current price system, a thorough investigation of the multi - price and multi - cabin pricing control system is made. fourth, based on the multi - agent theory, a new theory about the combination method of preponderant resources is presented. finally, the paper studies the reform of air cargo liability insurance mechanism in order to lower the risk of freight compensation responsibility of respective carriers

    在對我國航空貨運發展的現狀與趨勢、機遇與挑戰的分析基礎上，指出現有運作模式中存在的主要問題;通過對運作層、管理層和法律保障層的分別研究，構建我國航空貨運系統的整體結構模型;分析現有運價體系的弊端，著重研究運價的市場化問題，對「多等級多艙位」運價體系的建立進行初步探討;基於多代理理論，對優勢資源的整合方法進行研究;分析各承運方的貨物賠償責任風險，研究空運責任保險機制的改革問題。
  17. Pseud - sliding mode control in srd is lucubrated, the control law and the switch function of variable - structure control system with sliding mode ( vss ) are designed, the choice of the parameters of pi control and the theory of the combination control are discussed

    實驗結果表明準滑模變結構控制策略具有良好的動態性能和穩態性能，同時可以削弱傳統滑模控制的抖振影響，驗證了理論分析和數字模擬的正確性。
  18. It emphasizes the basic structure, the performance advantages, the technical principle, the system application and the test methods of the ac servo control system used for zj15 cigarette making & plug assembling combination

    重點概述了zj15型卷接機組中所應用的交流伺服控制系統的基本結構、性能優點、採用的技術路線及系統的應用與調試方法。
  19. Aiming at the weakness of electric - automation control system in combination reaction product line of chemical industry, this paper detailedly introductes how to reconstruct the former system successfully by applying the advanced plc, inverter, fieldbus and hmi, how to get to higher demand of producing technics and how to acquire better technique and economic benefit

    摘要針對化工化合生產線電氣自動化控制系統的缺點，詳細介紹了運用先進的plc 、變頻器、現場總線及hmi （人機界面）技術，對老系統進行成功的改造，達到了較高的生產工藝要求，並取得了良好的技術、經濟效益。
  20. The results obtained in the paper demonstrate that the sma passive control system is capable of significantly reducing the seismic response of the building. thirdly, through the combination of the different parameters of sma dampers, the influences of sma dampers on reduction effectiveness is studied and the optimal range of parameters are obtained

    研究結果表明：本文設計的sma耗能器可以有效地減小和抑制結構的地震響應；第三，根據耗能器不同參數組合下的彈塑性時程分析結果，研究了耗能器不同參數的變化對其減震效果的影響，給出了其參數的最佳取值范圍。
分享友人
分享到 Line

分享到臉書