comparison calibration 中文意思是什麼
comparison calibration
解釋
比較法校準- comparison : n. 1. 比較，對照；類似。2. 【語法】比較法；【修辭學】比喻。
- calibration : n. 1. 測定口徑。2. 刻度，標度，劃度數。3. 校準；標準化。
-
Contemporarily, comparison between analytic solver and numerical solver shows fairly satisfactory results and practical data is used to ascertain calculation parameter by calibration and validation
利用實測資料對模型進行了率定和驗證，確定了長江泰州江段和五里湖的模型計算參數。 -
Standard test method for calibration of pyrheliometers by comparison to reference pyrheliometers
日射強度計與基準日射強度計進行比較校準的標準試驗方法 -
Vacuum technology. ionization vacuum gauges. calibration by direct comparison
真空技術.電離真空計.用直接比較法校準 -
In view of predecessors " research achievements we put forward a method using square wave excitation and the fast furrier transformation ( fft ) to realize the comparison calibration for the calibration system of piezoelectric accelerometer
在吸收前人研究成果的基礎上，文中提出了工作用壓電加速度傳感器校準系統應用方波信號激勵，同時應用快速傅立葉變換（ fft ）的方法來實現比較法校準。 -
The calibration of piezoelectric accelerometer is an important area of the shock and vibration measurement technology, and the calibrated piezoelectric accelerometer is divided into standard accelerometer and working accelerometer, usually standard accelerometer is calibrated by absolute method and working accelerometer is calibrated by comparison method
壓電加速度傳感器的校準是振動與沖擊測量技術中的一個重要研究領域，被校的壓電加速度傳感器有標準加速度計和工作用加速度計之分，通常標準加速度計用絕對法校準，工作用加速度計用比較法校準。 -
Practice for secondary calibration of airborne particle counter using comparison procedures
用比較程序進行氣載顆粒計數器二次校正慣例 -
Comparison method of calibration
比較法標定 -
1 calibration the comparison of a measurement standard of instrument of known accuracy with another standard of instrument to detect, correlate, eliminate by adjustment, and report any variation in the accuracy of the item being compared
調校把一部己知其準確度的儀器的量度標準與另一儀器的標準作比較，來檢查、連系、更正並消除及報告比較專案的誤差。 -
So we want to do experiment about the roles of self - regulation and type of feedback in calibration study. the experiment design is : 3 ( achievement feedback, outcome feedback cortrol ) x2 ( high self - regulation, low self - regulation ) x2 ( male, female ). the tasks include standard task and comparison task
本研究的實驗設計採用3 （成績反饋組、結果反饋組、控制組） 2 （自我調節水平高、自我調節水平低的兩組學生） 2 （男、女）的組間設計，所用的實驗材料分為標準材料和對照材料兩種。 -
Comparison analysis and experiments show that the calibration instrument can meet the need of laser speedometer calibration because of its wide calibration range, high repeatability and universal performance
經各種校準方法的比較分析和校準試驗驗證，說明裝置校準范圍寬、重復性好、通用性好，可以滿足激光測速儀的校準需求。 -
20 50 calibration of gage blocks by contact comparison methods through 20 in. and 500 mm
用接觸式比較方法核準量塊 -
Inductive voltage dividers ( ivd s ) will be calibrated by comparison with the laboratory s 8 - dial ivd, normally at specific frequencies of 400 hz, 1 khz and 10 khz with an input test voltage of 25 v. the calibration normally involve measurement of voltage ratio ( magnitude ) of the output voltage related to the input voltage of the ivd
感應分壓器一般按400hz 、 1khz及10khz等指定頻率及25v的輸入測試電壓，透過與本所的八刻盤感應分壓器對比而進行校正。校正工作一般包括測量該感應分壓器輸入電壓與相對輸出電壓的電壓比（幅值） 。 -
The multi - port measurement system has the widespread use in microwave measurement, the measurement of multi - port device with two - port vector network analyzer ( vna ) is researched. this paper analyzes the commonly used error models and calibration methods of vna, program a trl calibration procedure for two - port vna, and compare the tested data with the data from vna. the comparison show that the programmed trl calibration procedure is in the same accuracy as the vna
本文討論了兩埠矢量網路分析儀常用的誤差模型和校準方法，編制了兩埠矢量網路分析儀基於trl校準法的校準程序，並把校準后的測量結果和矢量網路分析儀校準后的測量數據做了比較，比較結果說明編制的trl校準程序校準效果和矢量網路分析儀校準的效果相同。 -
Gas analysis - determination of composition of calibration gas mixtures ? comparison methods
氣體分析標準混合氣體組成的測定比較法 -
Methods for calibration of vibration and shock pick - ups. testing of temperature response by comparison
振動與沖擊傳感器的校準方法溫度響應比較測試法 -
Measurement microphones - methods for pressure calibration of working standard microphones by comparison
測量傳聲器.用比較片做用工作標準傳聲器的壓力校準方法 -
Measurement microphones - part 5 : methods for pressure calibration of working standard microphones by comparison
測量傳聲器.第5部分:通過比對進行工作標準傳聲器的壓力校準的方法 -
Vacuum technology. vacuum gauges. calibration. method by direct comparison
真空技術.真空計.直接比較法 -
Vakuum technology ; standard method for vacuum gauge calibration by direct comparison with a reference vaccum gauge, ionization vacuum gauge
真空技術.用參比測量儀直接比較校準真空計的標準方法 -
Vacuum technology ; standard method for vacuum gauge calibration by direct comparison with a reference vacuum gauge, thermal conductivity gauges
真空技術.通過與標準真空規的直接比較校準真空計的標
分享友人