composite layers 中文意思是什麼
composite layers
解釋
復合層-
The results of tem showed that the layers of omt had been separated partly into alone fragment by in - situ polymerization of pu ; the agglomerative nano - sio2 particles in pu composite had been dispersed, but the disperse status became worse as the increase of its content
Tem結果顯示，通過pu的原位聚合，復合材料中omt的片層被部分分離成單獨的片層;納米510 :粒子被分散，但在復合材料中的分散狀況隨著其含量的增大而變差。 -
At first, based on the results of in - situ load tests, the load - settle curves are acquired, and the effects of different reinforcement parameters are presented. these parameters include the linear density ratio ( ldr ) ; the location of the top layer of the geobelt measured from the bottom of the load plate ( u ) ; the different materials of geobelt ; the number of reinforcement layers ( n ) and the distance between the two layers of geobelt ( a h ). these results show that the bearing capacities of the reinforced composite foundation can be improved and the settlement can be reduced
首先，通過現場載荷試驗，獲取了加筋墊層復合地基荷載-沉降曲線，從筋帶鋪設的密度、筋帶的首層間距、不同筋帶材料、加筋層數以及雙層筋帶的層間距等幾個方面分析了以上加筋參數對加筋復合地基承載力的影響，指出筋帶的存在提高了加筋復合地基的承載力，減小了沉降。 -
The product is two layers of limpness composite material of polyester thin film coated with bonding agent and single surface bonding of calendaring aromatic polyamide fiber paper
該產品是由聚酯薄膜塗以膠粘劑，單面粘合軋光聚芳酰胺纖維紙而成的二層柔軟復合材料。 -
The results show that, composite could be fabricated on the complicated surface by means of sodium silicate sand mold combination with vacuum infiltration process. when the substrate was 10 mm, composite layers reached 3 mm to 5 mm in thickness with high strength interface and less casting defect. microstructures of grey cast iron and low chromium cast iron matrix composites with various volume fraction has been analyzed
結果表明：用水玻璃砂型（芯）加負壓鑄滲的工藝能夠實現復雜表面（曲面）顆粒增強復合材料的制備，澆注方式簡單可靠，基材厚度在10mm時，復合層厚度能達到3 5mm ，且復合層鑄造缺陷少，復合效果好，界面緻密而且結合強度高。 -
The omt after its suspension treated with ultrasonic wave was inserted with poly ( styrene - butyl acrylate ) emulsion. xrd test found the layers of omt particles were dispersed partly in the composite ; extraction experiment of nano - omt / pba - st composite indicated a great amount of macromolecule has inserted into the interlayer of omt. dta analysis showed the decompose temperature of composite has improved by 73 at 4 % omt
將omt的水懸浮液經超聲波處理，與苯丙乳液復合， omt p （ ba - st ）復合物的萃取和xrd試驗證明乳液的大分子已經大量嵌入omt層間，使大部分omt以納米級均勻分散於苯丙乳液之中； dta分析結果說明添加4 omt苯丙復合材料的分解溫度升高了73 。 -
This machine is suitable for producing 2 - layers or multiple - layer tri - side sealing composite film bag for foods, laundry detergent, candies etc. based on materials such as bopp, opp, cpp, pe, nylon, aluminum foil, and paper, it is an ideal packing bag making facility with easy operation and rapid working, making even - face, beautiful products with highly strong heating sealing. feature : 1. the whole machine adopts industrials control level computer and auxiliary three - servo control system. the pouch - making speed, pouch making length, temperature, countring punching and conveyor quantity of doubing finished products, etc. can be preset via touch screen
該機適用於以bopp opp cpp pe尼鋁箔紙張為基材的兩層或者說多層三邊封復合薄膜袋食品袋洗衣粉袋糖果袋等的生產，本設備操作簡便，產品平整，形狀美麗，封邊處熱合強度高，制袋速度快是理想的包裝制袋設備。 -
Making use of many layers composite technique and heat press technique to make artificial skull, through a series of performance testes ( including elongate performance, compress performance, curve performance, concussion performance, lay cut performance, concussion cut performance ), making use of drainage method to calculate its average density, which is 1. 25kg / m3, and combustion method to calculate its content of macromolecule, which is 57. 7 %
利用多層復合技術和模壓技術制備來的人工顱骨復合材料，通過對其一系列性能測試（包括拉伸性能、壓縮性能、彎曲性能、沖擊韌性、層間剪切強度和沖擊剪切強度等） ，證明了該復合材料具有良好的物理機械性能。採用排水法計算復合材料的平均密度為1 . 25kg m ~ 3 ，採用灼燒法計算復合材料的含膠量為57 . 7 ，證明該復合材料比強度較高。 -
Laminate : a composite material made by bonding together several layers of same or different materials
積層板（層壓板） ：由數層相同或不同材料黏合製成的復合材料。 -
The change of residual contact pressure of bimetal composite pipe under the action of heat load in this article, the possibility of separation between two metal layers in temperature cycle was researched ; it has been shown that under heat loading condition, it has a limit working temperature
摘要分析了在熱載荷作用下雙金屬復合鋼管結合強度的變化，研究了經歷溫度循環后內外層管之間出現松脫的可能性。 -
With concluding construction methods of composite soil nailing, and analysing the field measurements curves for two excavation engineering in soft layers, it is proved that using composite soil nailing in shallow foundation excavations is possible, at the same time groundwater should be treated carefully and deformations of the excavations should be controlled strictly
通過對兩個軟弱地層中復合土釘支護的基坑工程施工技術的總結及其變形測試數據的分析，說明在軟弱地層的淺基坑工程中應用復合土釘支護技術是可行的，但須認真治水及控制基坑變形。 -
Composite structures include layers, fibers, particles, and any combination of the three
分層結構的合成物由象三明治一樣的迭片構成的。 -
The main contents of the paper are : ( 1 ) review the state and art for fiber - wound vessel with metal inner lining ; ( 2 ) provide a method to present the technical features including wound process, equal stress dome and fiber gathering at the dome etc. ( 3 ) establish a finite element analysis model considering nonlinear physical and geometrical effects and develop a equivalent constitutive relation for winding graphite fiber reinforced plastic layers ; ( 4 ) set up a failure criterion for the inner metal lining and winding graphite fiber reinforced plastic layers ; ( 5 ) develop a corresponding engineering analysis code based on the commercial software ansys ; ( 6 ) investigate the plastic deformation and residual stress in the inner lining due to winding tension and pre - tension, and stress distribution of the composite vessel under service loading case
本文旨在為具有金屬內襯的纖維纏繞復合容器的參數設計提供分析模型、方法及工程軟體。論文主要內容是： （ 1 ）對復合容器分析國內外研究的概述； （ 2 ）復合容器的幾何表徵方法及工藝中若干力學問題； （ 3 ）復合容器結構分析的物理和幾何非線性有限元列式及其纖維層的等效本構關系； （ 4 ）復合容器的破壞類別； （ 5 ） ansys程序的二次開發； （ 6 ）典型復合容器的數值討論。本論文工作將對工程界復合容器設計和分析工作者具有參考價值。 -
The resulted films were densely packed uniform amorphous films with substantial overlap between adjacent si02 layers, and can serve the function as antireflection coatings. colloidal ti02 particles of 3 ~ 4nm in diameter were prepared using tetra - h - butyl titauate as precursor, and composite multilayer films of pss / tio2 were electrostatically self - assembled
二氧化硅膠體與聚合物pdda的自組裝多層復合薄膜為均勻、緻密的非晶態膜，復合薄膜內存在層間穿插的現象，薄膜表現出均質單層光學塗層的特性並具有增透作用。 -
It is suitable for ming and laying - off of leather, plastic cement, canvas, nylon, paper board, vacuum forming, composite material, blister cotton, package, and various kinds of synthetic materials in one layer or numerous layers
本機適用於皮革、塑膠、帆布、尼龍、紙板、真空成型、復合材料、泡棉、包裝及各種合成材料一層或數層的成型下料。 -
The problem that ommt resulted in pvc degraded was settled. but na - mmt in pvc / na - mmt composite was simply common filler, the space of the layers was 1. 29nm
通過力學性能測試發現，在蒙脫土含量為7phr時，硬質pvc的缺口沖擊強度最大提高了108 % ，彎曲模量也有所提高。 -
After analyzing 8 layers test data in 6 wells, we get the reservoir parameters of the nature fractured reservoir and the composite reservoir and the main fracture direction in this region
經對該區6口井8層試井資料分析，得到裂縫型油藏（包括寬而長的裂縫型油藏、壓裂后形成長裂縫型油藏）及復合型油藏參數，並確定了該區的主裂縫。 -
It is made of special filtering materid and also can be used to filter all leuds of medium and has high filtering mecision, especially composite filtering material is used inside in order to expand foul capacity storde in to filfering layers of filtering elements and molong to service life of filtering elements
採用了新研製的特殊濾材，可對多種介質進行超細顆粒污染的過濾，過濾精度高。使用特別復合濾材，擴大了濾芯濾層的納污容量，延長了濾芯的使用壽命。 -
Mepla composite pipes consist of 5 layers. the inside layer is made of cross - linked pe which make it possible to use one pipe for any applications like : hot water, cold water, potable water and heating distribution
吉博力mepla給水管有5層，其內層為交聯聚乙烯，它適用於儲如：熱水冷水直飲水及供熱系統的輸送。 -
In this article, the following technology of the carbon fiber composite flywheel in the integrated energy - storage / attitude - control system are analyzed and the valuable achievements are achieved above the foundation of consulting a large quantity of literatures and investigation : 1. different technology method for carbon fiber composite flywheel are designed, aimed at the character of carbon fiber composite material and manufacture 2analyzes the stress of carbon fiber composite flywheels made by different technology method, hoop - winding method, symmetric ortho layers pressing method, multi - layer winding method and interference joining method, under high rotate speed, builds their static model ; and simulates their technology and shape parameter ' s affecting their stress level with i - deas f. e. m
本文在查閱了大量國內外相關文獻及調研的基礎上，針對集成化儲能/姿態控制飛輪系統中的碳纖維復合飛輪的以下相關技術進行了研究，並取得了有價值的成果： 1針對碳纖維復合材料的特點及加工方式，設計了周向纏繞成型法、對稱正交鋪層層壓法、多層結構纏繞及過盈連接法等不同工藝方式的碳纖維復合飛輪轉子； 2針對不同工藝方式的碳纖維復合飛輪轉子，進行了高速旋轉狀態下的應力分析，建立了靜力學解析模型，並結合i - deas有限元分析軟體模擬模擬了不同工藝方式的碳纖維復合飛輪轉子的相關幾何參數及工藝參數對其應力水平的影響； 3 -
A composite of multi - layers with a liquid crystal sheet sandwiched in the middle, umu units are resistant to impacts ; a characteristic that makes them exceptionally safe products for a variety of applications
Umu可切換玻璃混合了包括液晶體薄片liquid crystal sheet在中間的多層玻璃. umu組件可抵抗撞擊，這個特點令到它們在任何應用下都安全
分享友人