composites 中文意思是什麼

composites 解釋
復合體
  1. Ablation performance of c c composites with different preforms

    炭復合材料燒蝕性能
  2. Ablation performance and mechanism of 3d c c composites

    復合材料的電弧駐點燒蝕及機理分析
  3. The development of adscititious particle reinforced aluminium matrix composites and al matrix in - situ composites reinforced by reaction synthesis " reinforcement phase are reviewed at first. and the papers point out the difficulties and problems on the study of al matrix composites at present

    本文首先回顧了外加顆粒增強鋁基復合材料和反應合成強化物增強鋁基原位復合材料的研究進展，指出當前鋁基復合材料研究中存在的問題。
  4. The results show that there is anomalistic crystal whose size reaches nanometer grade in fine pvc ; the crystal structure is damaged by jet - milling, which induces the melting point of nanocrystal pvc decreases from 210 to 128. the nanocrystal pvc induces the decrease of plasicizing time and equilibrium torque and the increase of maximal torque, which show that the nanocrystal pvc have self - plasticization in pvc composites

    通過sem 、 tem 、 ftir和dsc測試表明：氣流粉碎制得的pvc微粉中具有不規則納米晶體；氣流粉碎破壞了pvc的晶體結構，使納米晶pvc的熔點從210下降到128 ；納米晶pvc使體系塑化時間、平衡轉距的降低、最大轉距升高，具有自增塑作用。
  5. Antifriction mechanism of graphite and mos2 in epoxy composites

    2的減摩作用機理
  6. The composites not only show excellent photo - responsive properties in the visible and near - ir region ( 450 ~ 850 nm ), but also show complementary and synergetic enhancement effects in photosensitivity in the visible and near - ir region. the reasons for the enhanced photoconductive properties and new effects are explained in terms of the partial and directional charge transfer from phthalocyanine to azo compound in these azo / tiopc composites. 2

    研究發現這兩種復合材料體系在可見光區和近紅外光區（ 450 850nm ）均有光譜響應，光譜響應范圍得到了拓寬，並在該波長范圍內都有優良的光電導性能，呈現出明顯的光電導性能協同增強和互補效應，該復合材料體系中酞菁向偶氮發生的部分定向的電荷轉移是光電導性能協同增強和互補效應產生的物理起因。
  7. Numerical simulation on solute segregation during solidification in fiber reinforced aluminum - copper binary alloy composites

    短纖維增強鋁銅二元合金復合材料凝固偏析的數值模擬
  8. Ptfe has many excellent properties such as : bonzer self - lubrication ^ low fricatiom chemistry stabilization and thermal stabilization, but its wear resistance is very low to improve the wear resistance of ptfe a lot of researches have been down by means of adding fillers to it, there are still less report on nano - inorganic filler filled ptfe composites to change properties. in this paper, experimental study was made to question above problem

    Ptfe具有優異的自潤滑、低摩擦、化學穩定性和熱穩定性，但耐磨性較差，因而人們在利用不同種類的填料對ptfe進行填充改性，提高耐磨性方面作了大量研究工作，但在使用納米無機填料填充改性ptfe方面研究很少，因此本課題主要探討這一方面的問題。
  9. Most reflections are interference composites.

    大多數反射都是干涉復合而成的。
  10. The main classes of materials are metals, polymers, ceramics, and composites.

    材料的主要分類為金屬、高聚物，陶瓷，及合成材料。
  11. The al matrix composites by reaction synthesis put up high mechanical behavior, well high - temperature properties and excellent wearing quality but the existent difficulties lie in that homogenizing method is not perfect, fundamental research to growth mechanism is absent and the concomitance compound come from reaction is difficult to eliminate at present

    反應合成的鋁基復合材料具有常溫力學性能高、高溫性能好和耐磨性突出的優點，而存在的主要研究難題則是整個材料均質化方法不理想、生長機制等基礎理論研究缺乏、反應伴生的化合物難以控制等。
  12. Effective moduli of composites based on confocal ellipsoid model

    基於共焦點橢球構型的復合材料有效性質預測
  13. By "multicomponent systems" polymer chemists mean polymer blends, copolymers and reinforced composites.

    聚合物化學工作者所稱的「多組分體系」是指聚合物共混體，共聚物和增強復合材料。
  14. Consequently, with increasing mmt content, the tensile strength and young ' s modulus of hdpe - g - aa / mmt nanocomposites increased, while that of hdpe / mmt composites decreased. moreover, the addition of mmt to hdpe - g - aa decreased the melting temperature and the degree of crystallization of the matrix. these changes may be attributed to high interfacial adhesion between hdpe - g - aa matrix and exfoliated clay, which reduces the mobility of crystallizable pe chain segments, and subsequently reduces the crystallization ability

    研究結果表明： mmt在hdpe中不能達到納米級分散，而在hdpe - g - aa中， mmt能以插層型利剝離型的結構存在，這主要是由於極性的丙烯酸接枝在hdpe上提高了後者的極性，而且能與mmt上的活性基團進行化學反應，從而提高了pe鏈進入mmt層間的可能性，使mmt在基體中達到納米級分散。
  15. Progress in crystalline particulate and dendrite toughened metallic glass matrix composites

    枝晶增韌非晶基復合材料的研究進展
  16. In this dissertation, al - si / sicp composites brake rotor with diameter of 1200mm was firstly fabricated by a novel spray deposition technology, and simultaneously coupled brake pad was prepared by a novel dry - powder processing route, termed as two - step pressing process. a wedge pressing technology was developed to densify the as - produce al - si / sicp composite brake rotor

    本文首次採用噴射沉積技術制備了直徑達1200mm的al - si / sicp制動盤，同時採用二次壓制工藝制備出了配套的合成閘片，研究了制動盤的楔壓緻密化技術、機理，復合材料摩擦磨損性能及機理。
  17. As an advanced materials preparation technology, spray - deposition has shown remarkable superiority in producing large - sized alloys and metal matrix composites. however, the spray deposeted preforms usually contain a certain quantity of porosity. besides, the oxide films on the surface of the particles lead to week metallurgic conjunction between the particles. in order to obtain an ideal structure and performance, the porous preforms need further densifying and plastical forming. in this paper, a new technology named wedge pressing was used to densify spray - deposeted 5a06 aluminium alloy, in which the large deformation can be obtained through the sum - up of local deformation and multi - step small deformation. this method can also solved the problems in traditional processing and greatly decreased the producing cost. what ’ s more, the reserch on the wedge pressing desification rules about the large - sized spray deposeted preforms was significant it was vital not only to the further densification of the prefoums but also to the further research on plastical deforming the research was also benefit to the industrialization an the application of the spray deposeted porous materials

    坩堝移動式噴射沉積技術作為一種先進的材料制備新技術，在制備大尺寸合金及金屬基復合材料方面具有顯著的優越性。然而噴射沉積坯件特別是大型坯件通常存在一定量的孔隙，顆粒表面存在一定量的氧化膜，顆粒之間未能完全達到良好的冶金結合狀態，因此需要進行后續緻密化和塑性變形才能獲得理想的組織和性能。本文採用一種新型的楔形壓制工藝，即通過局部變形、多道次小變形累積實現大變形的緻密化加工方法，對噴射沉積多孔坯料進行后續緻密化和塑性變形，很好地解決了傳統加工工藝的難題，大大降低了生產成本。
  18. With the filling of diabase, the mechanical properties of the composite increased first and then decreased with a top tensile strength of 56. 5mpa and a top impact strength of 70. 1mpa. these illuminated that the diabase fiber reinforced pvc composites could be used as structure materials

    復合材料的力學性能隨著輝綠巖的增加先升后降，復合材料拉伸強度最高可達56 . 5mpa ，復合材料沖擊強度最高可達70 . 1mpa ，說明輝綠巖纖維增強pvc復合材料作結構材料使用。
  19. Study on properties of tde - 85 aromatic diamine matrix and carbon fiber composites

    芳香胺樹脂基體及碳纖維復合材料性能
  20. Nano - tiopc60r, 40nm / ctm / pc = l / 80 / 100, s762. 5nm = 0. 533cm2 / u j ) ; thereby the single - layer nanoparticle tiopc / fluorinone - based azo composite photoreceptors were prepared and their photoconductive properties were briefly studied. in conclusion, two originalities can be outlined from this thesis : ( 1 ) by using 1, 4 - dioxane as disperse solvent, stable and uniform composites of tiopc, azo, hydrzone and polymer matrix were prepared, and the single - layer photoreceptors were successively fabricated with these composites, the photoreceptors showed high and wide range photosensitivity from visible to near infrared spectral regions

    綜上所述，本論文主要有以下兩個創新之處： （ ）採用兩雜性的二氧六環做分散溶劑，成功地實現了酞警氧鈦、綠丹藍偶氮、茶苯晚以及聚合物介質組成的、多相多組分體系的穩定復合，從而制備出從可見光到近紅外光區都具有高光敏性的寬頻響單層復合光導體。
分享友人
分享到 Line

分享到臉書