compression stroke 中文意思是什麼

compression stroke 解釋
壓縮沖程
  • compression : n. 1. 壓縮；壓緊；濃縮，緊縮。2. 加壓；壓抑。3. （表現的）簡練。4. 應壓試驗。
  • stroke : n 1 一擊，一敲；打，打擊；一振，一動；（字的）一筆；一舉；一劃；（游泳的）一爬；一觸；一閃；一刀...
  1. Then diesel fuel oil is injected or sprayed into the cylinder at the end of the compression stroke.

    然後在壓縮沖程即將結束時，柴油燃料被噴射或被噴霧進入氣缸。
  2. The thesis describes the detailed procedures of hand - writing data processing, including chinese character dot matrix building and display, vector data storage, chinese character dot matrix compression, transfer protocol and hand - writing chinese character re - building. also, stroke order based hand - writing chinese character recognition method is explored, and characteristic - recognition methods for chinese character with similar stroke order codes and the structure of hand - writing chinese character recognition dictionary are discussed

    第四，設計了服務器端的服務軟體，可以實現數據的解碼、重建、筆劃特徵提取、識別、數據管理功能；採用了基於筆段筆順編碼和結構特徵的識別方法並設計了識別字典的結構，可以有效的提高識別速度，達到較高的識別率。
  3. Exchange - compression stroke

    換氣壓縮行程
  4. When the engine runs in compression stroke and power stroke, the valves must close tightly on their seats to produce a gas - tight seal and thus prevent the gases escaping from the combustion chamber

    當發動機處于壓縮行程和做功行程時，閥門必須緊緊地關閉以產生一個不透氣的氣封，以防止氣體逃離燃燒室。
  5. In this thesis, we discuss the compression method of chinese font and put forward a method based on stroke extraction

    本文在對漢字字形的結構式壓縮進行了討論的基礎上提出了一種基於筆劃抽取的漢字字形結構式壓縮方法。
  6. The 2 stroke book says because of testing, an 8 degree angle of divergence for the diffuser cone connected to the lead in pipe is the minimum angle to start with and 20 degrees for the compression cone at the other end of the pipe is a good starting point

    二行程手冊測試，一個八度的漸縮圓錐反射角，連接導入氣管通道，是一個極小的開始角度，以及20度的壓縮圓錐在氣管的另一結束端，是一個好的開始
  7. This is the four - stroke cycle which is in common use. an alternative is the two - stroke cycle, which combines the exhaust and compression strokes into one

    這就是常用的四沖程循環。另一種循環是兩沖程循環，它把排氣沖程與壓縮沖程合併為一個沖程。
  8. In this paper, the general theory and numerical solution procedure were described. by building a diesel modeling with vertical valves and a piston bowl, a whole cycle was calculated, which include intake stroke, compression stroke, expansion stroke and exhaust stroke

    通過對帶有進、排氣門的柴油機進行計算，模擬了一個完整循環內進氣道、氣門和缸內氣體流動的全過程。
  9. On the basis mentioned above, another mathematical model for the supercharged diesel was set up. according to this model some results of simulation calculations were given. the characteristics of operation of the diesel in wet compression : including the excess air coefficient, the cylinder temperature at the beginning of compression stroke, the maximum temperature in the cylinder, the cylinder thermal load, the specific fuel consumption, and efficiency of diesel engine were obtained

    在此基礎上，又建立了增壓柴油機濕壓縮的數學模型，對噴水后柴油機的各性能參數，諸如過量空氣系數、氣缸進氣溫度，缸內最高溫度、氣缸熱負荷、比油耗、熱效率等進行了模擬計算，為增壓柴油機進口加濕技術的研究提供了理論依據。
  10. It was found that the compression speed and compression stroke are the two factors affecting the molding pressure most significantly

    由模擬找出了壓縮速度與壓縮行程是兩個影響成型壓力極大的因素。
  11. Using lower switch time, lower compression speed and higher compression stroke will result in lower cavity pressures

    使用較短的切換時間、較低的壓縮速度以及較高的壓縮行程將產生較低的模安穴壓力。
  12. Simulation and the associated numerical algorithm on the injection - compression molding ( icm ) process were developed to understand processing characteristics by changing processing parameters including compression speed, switch time from injection to compression, compression stroke as well as initial cavity thickness and part thickness using disk parts

    摘要射出壓縮成型的模擬以及數值運算是要了解成型參數的改變，包括：壓縮速度、射出與封裝的切換時間、壓縮行程等製程特性而創建的，同時也包含了初始的開模厚度以及使用在光盤片的成品厚度。
分享友人
分享到 Line

分享到臉書