compressor work 中文意思是什麼

compressor work 解釋
壓氣機功
  • compressor : n. 1. 壓縮物。2. 壓縮器，壓氣機，壓榨器。3. 【解剖學】收縮肌，壓肌。
  • work : n 1 工作，操作，勞動，作業；工件；功課；努力；行為，作用。2 （待辦的）事務，業務；職業。3 〈前有...
  1. The frame structure, work flow and 3 - dimensional model building method of the virtual prototype design of the air compressor are presented in detail

    摘要闡述了空壓機虛擬樣機設計的框架結構、工作流程及其三維模型構建方法，進行了設計與運動學模擬方法研究。
  2. 3 ) aerial compressor reconstruction with inflator labyrinth seal : the aerial compressor formerly adopted simple inflator labyrinth seal and it did n ' t work well due to the vast leakage and frequently abrasion of the labyrinth seal, so the machine could n ' t operate in long term

    3 ）富氣壓縮機充氣式迷宮密封的技術改造，焦化裝置富氣壓縮機原來採用簡單的充氣式迷宮密封，密封效果不好、泄漏大，迷宮密封頻繁損壞，機組無法實現長周期運行。
  3. Experimental studies on s1a - 02 gas turbine with water injection into compressor interstage / inlet as well as that on turbocharger self - loop test rig with inlet water injection are introduced. test results are in good accordance with simulation results, wet compression can lower compression work and increase engine power output so engine performance is enhanced, if engine power output is not changed, efficiencies of compressor and this engine become higher and turbine inlet temperature and fuel consumption become lower and if keeping t4 the same as that before wet compression is used, efficiencies become furthermore higher and engine power output increases greatly

    實驗結果和計算結果同樣表明：濕壓縮減少了壓氣機所消耗的壓縮功，增加了燃氣輪機的輸出功率，提高了燃氣輪機性能，如果保持發動機輸出功率恆定，濕壓縮可以提高壓氣機和整個燃氣輪機機組的效率，與此同時，渦輪進口溫度t _ 3 ~ *和燃油消耗率下降；如果保持渦輪排氣溫度t _ 4 ~ *恆定，壓氣機和燃氣輪機機組效率進一步提高，燃氣輪機輸出功率增加。
  4. To research the energy transformation and utilization orderliness of the new proposed system is the main objective and content of this dissertation, as follows : about two thirds of the work output of the turbine is consumed by the compressor. traditionally, every way of inter - cooling adopted in gas turbine decreases the work consumption of compressor in some degree. through the spraying of water at the entrace of compressor, the air can be continuously cooled in compression so that the work consumption can be reduced greatly

    本論文從以下幾個方面進行了研究：由於燃氣輪機循環中壓氣機消耗近2 3的透平出功，傳統上採用的各種間冷方式都一定程度地降低了壓氣機耗功；而壓氣機入口採用注水方式，可以對壓縮空氣進行連續冷卻，以達到大幅度降低壓氣機耗功的目的。
  5. They will short down the working life of air compressor because they are always started or stopped when we want to make the railway carriage stay in a fixed temperature. now, automatic and intelligent control systems are being applying in bus air - conditions control. in this way, computers control the work of air compressor, the turnaround speed of fan, the open degrees of wind controlled doors and so on

    我國大多數客車空調仍然採用簡單的壓縮機開關控制及循環離合控制系統，如：離合器?熱力膨脹閥系統（ cctxv ）和離合器?節流管系統（ ccot ） ，這些控制方式的精度低，當進行恆溫控制時壓縮機處于頻繁的開、停狀態，縮短了壓縮機的工作壽命。
  6. Experimental study of rotary compressor under heat pump work condition

    弦月形狹縫通道內液氮受迫流動沸騰傳熱強化的研究
  7. A compressor is removed. and lifted by the crane. this dismantling work was works with 3 workers

    蒸機力?榨空?作吊上大形部品集積場所運
  8. A model of letting out of no oil ubricated double whirlpools vortex air compressor was set up, the length of leak line of one cycle was calculated the change of the leak line at work, the change of the length of leak line varying with the crank corner, and the change of the leak amount varying with the pressure of revealing atmospheric and crank corner were analyzed

    摘要建立了無油潤滑雙渦圈渦旋壓縮機的泄露模型，根據型線的幾何理論計算了一個周期內泄漏線的長度，分析了在工作過程中泄漏線的變化，泄漏線長度隨曲柄轉角的變化，以及泄露量隨排氣壓力，曲柄轉角的變代情況。
  9. So it is very important for qing ' an, a domestic manufacture of compress which can do the r & d work of compressor and controller of rac by itself, to catch up with the world trend in such area. also it will do great help to increase the quantity of production line and the shipment of qing ' an if qing ' an can make the inverter controller for air conditioner by itself

    慶安製冷作為國內唯一擁有自主知識產權的空調壓縮機生產商，是否應該利用自身的技術優勢在短時間內進行交、直流變頻控制器和壓縮機的批量生產，以達到穩固已有壓縮機市場、拓展產業種類的目的，是擺在慶安製冷面前的一個緊迫問題。
  10. It specifies the process of the design, simulation and experiment of liquid cooling system. main contents of the thesis are as follows : description of the present usage of liquid cooling system, presentation of a new type of liquid cooling system and description of its work principles ; design of the liquid cooling system, which mainly deals with the design and collating calculating of serpentine condenser and heat exchangers adopted in this system. meanwhile, the model chosen calculating of compressor 、 thermal expansion valve 、 plate evaporator 、 water pump and the like equipment used in the system are also carried out

    本文的主要內容如下:對液冷源使用現狀進行了描述，提出了一種新型液冷源系統並對其工作原理進行了闡述;對系統進行了設計，主要對系統中所採用的管帶式冷凝器和水側空/液換熱器進行了設計和校核計算，同時對系統中所用到的壓縮機、熱力膨脹閥、板式蒸發器、水泵等配套設備進行了選型計算;分別對製冷系統和冷卻液循環系統進行了數學建模。
  11. While using spiral shell s pole compressor to work, seal by the fluid

    使用螺桿壓縮機工作時，靠油液密封。
  12. We analyzed the centrifugal compressor ' s loading types, made certain the shift gears running work conditions of the centrifugal compressor, and putted forward the shift gears running energy - saving ratio calculational methods of centrifugal compressor, and discussed the centrifugal compressor ' s anti - surge conditions, and getted set the running ratating speed optimized mathematics model of centrifugal compressor

    分析了離心式壓縮機的負荷類型，確定了離心式壓縮機變速運行工況，提出了離心式壓縮機變速運行節能率計算方法，討論了離心式壓縮機的防喘振條件，建立了離心式壓縮機運行轉速優化的數學模型。
  13. Compared with the scroll compressor of traditional circle profile, it has the advantages of high efficiency, little leakage and high quotient of volume using. the research work is given as follows. a whole volume theory for the scroll chamber working process of new type combination profile compressor is set up

    論文的研究工作主要表現在以下幾個方面:論文對新型分段組合曲線渦旋壓縮機的容積理論進行了論述，系統地研究了組合曲線渦旋壓縮機各個壓縮腔容積的求解方法。
  14. Thermoacoustic prime mover is an absolutely new type of compressor. it has n ' t any moving part so it can work for a long period without maintenance. waste steam and solar energy can be used as its heating - resources so that it has many applications especially for the places having no electricity supply

    熱聲驅動器是一種與常規機械式壓縮機完全不同的新型驅動器，它沒有機械運動部件，可使用低品位能源，具有結構簡單、運行可靠、無維修工作時間長等優點。
  15. The design and research work on the inlet turning tube had been carried out mainly based on the experiment results and working experience. with the development of computational fluid mechanics ( cfd ), it is quilt possible to simulate the flow inside the inlet turning tube accurately and get a better understanding of the flow phenomena in the flow field to guide the design, in this paper, detained simulations of the flow fields inside two different compressor inlet turning tubes have been presented

    過去國內對它的設計和研究主要藉助于經驗和利用實驗手段來進行，本論文使用先進的三維氣動計算技術，藉助功能強大的流場計算軟體，對壓氣機進氣彎管內部流動情況進行了詳細和準確的數值模擬，為壓氣機進氣彎管的優化設計提供更為準確的理論依據及指導原則。
  16. It requires more even airflow and avoids the tremble of the compressor and the instability of gas turbine. at the same time, the dimension of the inlet volute must be as small as possible, so that the gas turbine can work well

    一方面，它要求流經進氣蝸殼的氣流盡量均勻，以免造成壓氣機的喘振和整個動力裝置性能的不穩定；另一方面，要求進氣蝸殼結構尺寸在保證要求的前提下盡量小，有利於機艙的布置。
  17. This essay has touched upon the following work : 1. has built up theoretic models including static mathematic models of air compressor, combustion chamber, gas turbine, waste heat recovery boiler and steam turbine which are deduced according to the feature and theory of the equipment of the object of study. upon establishment of each model based on the actual conditions, a method of multiple imitation and combination is applied to parts which have already got characteristic curves to have achieved quite accurate curves whilst the method of neural net is applied to the parts which have no characteristic curves for establishment of models

    本文進行了以下的主要工作：建立理論模型，根據對象的實際設備的特點和理論關系推導壓氣機、燃燒室、燃氣輪機、余熱鍋爐、汽輪機的靜態數學模型；根據本研究的實際情況，在建立各部件模型時，對已有特性曲線的部件，採用多項式擬合的方法，得到較為準確的特性，而對部分沒有曲線的特性，則採用神經網路的方法建立模型。
  18. Using energy transformation method, the characteristic map of the compressor of si a - 02 gas turbine is gained. and based on this work, effects of wet compression on compressor ' s steady - state performance are studied, which is compared with experimental results

    本文根據能量轉換方法計算得到了s1a - 02燃氣輪機的壓氣機特性線，在此基礎上分析了噴水后壓氣機特性線的變化情況，並與實驗結果進行了比較。
  19. From the air valve operating principles of view, air valve performance will directly affect the work of compressor tanks, air valve for the following requirements : resistance losses small

    從氣閥工作原理來看，氣閥工作性能將直接影響壓縮機氣缸的工作，因此，對氣閥有如下要求：阻力損失小。
  20. My research work is carried out to this target firstly, i do my work on the many mechanisms of dehumidification & refrigeration, researching environment - protecting and energy efficient methods of dehumidification & refrigeration - - dry fixed bed dehumidification & solar energy solid absorption refrigeratioa dry fixed bed dehumidification has been put in practice successfully instead of wheel dehumidificatioa solar energy solid absorption refrigeration substitutes for evaporation compressor refrigeratioa on the bases of the researching, i integrate dry fixed bed dehumidification with solar energy solid absorption refrigeration into a whole system - - dcs, which is drived by solar energy

    然後在此基礎上，對除濕和製冷進行集成，組成一個完整的除濕製冷系統? ?太陽能開式循環除濕製冷系統，希望以此代替目前我們在工程中由乾式固定床型除濕和蒸汽壓縮式製冷所組成的集成系統。該系統保持了既有的功能，既可以單獨進行除濕供干風或製冷供冷風運行，還可以進行除濕和製冷的協作供乾冷風運行；並且整個系統的主要能耗來自太陽能，使其環保、節能。
分享友人
分享到 Line

分享到臉書