contraction flow 中文意思是什麼

contraction flow 解釋
收縮流動
  • contraction : n 1 縮短，收縮；【醫學】攣縮。2 （開支等）縮減；收斂，狹窄；縮度。3 【語法】縮略〈如將 never 略成...
  • flow : vi 1 流，流動。2 （血液等）流通，循環。3 流過；川流不息；（時間）飛逝；（言語等）流暢。4 （衣服、...
  1. Ptfe is one of the most corrosion - resistant materials in the world. however it has defects such as the hot expansion and cold contraction rate is10 times larger than that of steel and the original cold fluidity ( creeping ) etc. therefore, as temperature increases, ptfe extends so excessively that it would collapse and then block the flow of media ; as temperature decreases, ptfe contracts so excessively that it would be ripped and then cause leakage

    Ptfe是當今最耐腐蝕的材料之一，可它被製造成襯里的時候，會存在熱脹冷縮比鋼鐵十多倍及固有的冷流性等缺陷，致使ptfe襯里管道、設備，在使用過程中，溫度高時， ptfe襯里層會伸長過多而內癟，阻塞了介質流通；溫度低時， ptfe層會收縮過大被拉裂而泄漏。
  2. What flow is that, we use model simulation to analyze the em algorithm contraction ratio. through network simulating, we analyze the factors which can influence loss inference algorithm accuracy like measurement strategy or routing algorithm. we analyze the accuracy and contraction characteristic of multicast - based direct algorithm and em algorithm, and compare the error factor between them

    實驗中通過網路模擬模型，確定了em演算法的收斂速率;研究了不同測量策略和路由器擁塞避免演算法對丟包率推理演算法準確率的影響;分析了單點多播的de和em演算法準確性、收斂性等特徵，通過比較兩種演算法的統計誤差，得出em演算法略優于de演算法的結論。
  3. Digital tv qpsk modulation in the treatment of the data flow of energy to deal with the proliferation of randomization, rs codeconvolution interleave contraction coding, modulation before forming the base - band processing to ensure that the data transmission performance

    Qpsk數字電視調制器在對數據流的處理上採用能量擴散的隨機化處理rs編碼卷積交織收縮卷積編碼調制前的基帶成形處理等，保證了數據的傳輸性能。
  4. For the larger area contraction ratio, the flow condition becomes more complicated, the discharge of the tunnel and the change of the negative pressure in the cavity pocket will be reduced, but the cavity diameter of the level rotary cavity flow and the dissipation ratio of the system will be increased

    面積收縮率較大時，流態變化復雜，泄流量和環流空腔內的負壓的變化減小，但空腔環流的空腔直徑和泄洪洞的消能率增大。
  5. This control cabinet can control every point temperature in the hot runner, and keep a plastic flow at an optimum condition so that it is possible to avoid such defects as hollow and contraction cavity from lacking in supply, and to save materials and labor and reduce production costs at the same time. compared with ordinary, such hot runner will shorten the time of mould removal, carry out full - automatic ordinary, such hot runner will shorten the time of mould removal, carry out full automatic operation more easily, reduce the distance of mould - opening and the stroke of mould - closing

    使用本控制櫃能精確控制流道中各點溫度，使塑料流動達到最佳狀態，這樣能克服製件因補料不足而產生凹陷，縮孔等缺陷，同時節省了材料和人力，降低生產成本，與普通流道比脫模周期短，易實現全自動操作，可以縮短開模距與合模行程，縮短成型周期，可以成型較長製品。
  6. In this thesis a numerical model to solve the planear 2 - d depth - integrated flow ( dif ) has been established with irregular body - fitted mesh finite volume method and explicit maccormack predictor - corrector method and applied to the study of damming caused by a bridge pier under 14 working conditions varied with the combination of different pier shape. flow rate and contraction ratio

    本論文採用非規則貼體網格有限體積法和顯式maccormack預測-校正法求解平面二維水深積分方程，對明渠水流運動的數值模擬方法進行了研究，並且應用該數值模型計算了14種不同的橋墩體型、來流、收縮比的組合工況下的橋墩壅水問題。
  7. The influence of the area contraction ratio of rotary flow generator on the hydraulic characteristics of level rotary flow has been investigated by the hydraulic model test of an internal energy dissipation tunnel

    摘要通過模型試驗，研究了起旋器出口面積收縮率對水平旋流泄洪洞水力特性的影響。
  8. The area contraction ratio has obvious influence on the flow pattern, discharge, wall pressure and air pressure inside level rotary flow

    研究發現面積收縮率對流態、泄流量、壁面壓強和空腔內的氣體壓強均有較大的影響。
  9. In this dissertation, following the ideas of gage and hamilton, we investigate some special planar curvature flow of contraction and expansion. the paper consists of three chapters

    本文遵循gage - hamilton研究曲線收縮流的思路，針對特殊的平面曲線收縮流和擴展流，我們得到了相類似的一些結論，文章共分三部分。
分享友人
分享到 Line

分享到臉書