cooling ring 中文意思是什麼
cooling ring
解釋
冷卻環-
The innovation is that a ring bar sprayed bubbling gas distributing device is installed at the bottom of the tower, which has novel effects of leveling off gas and decompressing, cooling and dust removal, highly effective absorption, hydraulic stiring and so on at the same time
其創新點是在塔的下部嵌入了一個環柵噴射鼓泡式進氣裝置，其新穎之處體現于：煙氣穩流減壓，冷卻除塵，高效吸收，氣力攪拌等功能可在環柵通道內一氣呵成。 -
The degrees of crystallinity of pure ptfe under the different conditions of water cooling, air cooling and furnace - varying cooling were made comparison by xrd. the thermal stability of pure ptfe and solid lubricant was analyzed by dsc - tg ; the composition and valence state of elements in the surface of carbon fiber, solid lubricant before and after friction test and lubricant transfer film were characterized by xps ; the frictional property of solid lubricant was tested by pin and disk test rig. the frictional wear property of solid lubricant between embedded bearing sleeve and steel axle friction pair ring was tested by special simulate test machine, the hardness of solid lubricant was tested by pm ; the compression strength of solid lubricant was tested by material test machine
用sem表徵原料微觀結構、摩擦表面及潤滑轉移膜表面形貌：用xrd進行原料物相分析，及比較水冷卻、空氣冷卻、隨爐冷卻三種工藝條件下的純聚四氟乙烯樹脂的結晶度；用dsc - tg分析純聚四氟乙烯樹脂及固體潤滑劑的熱穩定性；用xps表徵碳纖維表面、固體潤滑劑摩擦前後表面、潤滑轉移膜表面的元素組成、價態變化；用銷盤式摩擦磨損試驗機對固體潤滑劑進行摩擦性能測試；採用專用的臺架模擬試驗機對固體潤滑劑鑲嵌軸承套與鋼軸摩擦副間的摩擦磨損性能進行測定；用萊次偏光顯微鏡（ pm ）測試固體潤滑劑的硬度；用材料試驗機測試固體潤滑劑的抗壓強度等。 -
This equipment is mainly composed of braising apparatus 、 condenser 、 balanced water tank 、 material pump 、 circulating pump of cooling water 、 double water - ring vaccum pump 、 connecting pipeline and electrical control box
本設備主要由閃蒸器、冷凝器、平衡水箱、出料泵、冷卻水循環泵、雙級水環式真空泵、聯接管道及電器控制櫃等組成。 -
The vacuum gas quenching process of ring die of pellet mill is analyzed and discussed based on selection of heat treatment equipment, setting of process parameters, comparison of gas quenching cooling medium and control of deformation amount and others
摘要對飼料制粒機環模的真空氣淬工藝，從熱處理設備的選用、工藝參數的設置、氣淬冷卻介質的比較及變形量的控制等多個方面進行了分析和討論。 -
On the other hand, for the pre - press stress being threw by the hub was inserted after cooling with liquid nitrogen, the poor transverse tension strength of the multi - ring flywheel rotor could be counteracted. so the rotate speed and energy storage density can be increased efficiently
而採用多環套裝纏繞技術製造的多層飛輪輪環，在利用溫差過盈裝配方法給復合材料輪環施加預壓應力后，能夠有效避免飛輪轉子的復合材料輪環部分因較低的纖維橫向抗拉強度而破壞失效，從而大幅度提高飛輪轉子的極限轉速和儲能密度。
分享友人